CASIO QW-3558 Mens Watch User Guide
- June 13, 2024
- Casio
Table of Contents
CASIO QW-3558 Mens Watch User Guide
Reading The Display
(Reversion to regular time) The watch reverts to the regular timekeeping display after operating in any mode. (Auto return feature) The watch will return to the regular timekeeping display automatically if you do not perform any operation for five or six minutes in the calculator or alarm display.
You can also find information about operational procedures at the CASIO
website.
https://support.casio.com/global/en/wat/model/3558/
Calculator Operation
| EXAMPLE | OPERATION | READ-OUT |
|---|---|---|
| Basiccalculation:(12 – 0.5) × 3 ÷ 7= 4.9285714 … | 12537 | |
| Constantcalculation:3 + 4 = 7 (4 is constant) | 43 | |
| 8 + 4 = 12 | 8 | |
| 3 – 4 = –1 | 43 | |
| 8 – 4 = 4 | 8 | |
| EXAMPLE | OPERATION | READ-OUT |
| --- | --- | --- |
3 × 4 = 12
(4 is constant)
| 4
3
|
|
8 × 4 = 32| 8|
3 ÷ 4 = 0.75| 4
3
|
8 ÷ 4 = 2| 8|
Power
calculation:
32
|
3|
33| |
To save battery power, press the B button in the calculator mode to
silence the tone. To retrieve sound, press the B button again.
Setting Daily Alarm Time
Every time the button is pressed in the alarm mode, the alarm-ON-mark ( ) appears or disappears. When the alarm-ON-mark is lit, the buzzer sounds for 20 seconds at the preset time every day until cleared. To stop the buzzer while sounding, press any button. (Setting the time signal) Every time the button is pressed in the alarm mode, the time-signal-ON-mark ( ) appears or disappears. When the time-signalON-mark is lit, the watch sounds every hour on the hour. (Sound demonstration) While both and buttons are pressed simultaneously, the buzzer sounds.
[Presetting alarm time]
-
Press B to set new alarm time.
-
Press to set PM or AM.*
-
A numeral can be entered in the flashing position by pressing the required numeral key. The flashing digit can be shifted in the following order:
-
Press B to complete setting.
- When the watch is in the 24-hour system, the alarm time is displayed in that system.
Setting Dual Time
-
Press B to set new time in dual time mode.
-
Press to set PM or AM.*
-
A numeral can be entered in the flashing position by pressing the required numeral key. The flashing digit can be shifted in the following order:
-
Press B to complete setting.
- When the watch is in the 24-hour system, the dual time is displayed in that system.
Stopwatch Operation
A signal confirms start/stop operation. The tone sounds at 10-minute intervals. (Working range) The stopwatch display is limited to 23 hours 59 minutes 59.99 seconds. Thereafter it can be reset and started again. The hour digits can be shown by pressing the button.
(a) Elapsed time
(b) Lap time
(c) Two finishes
Setting Time And Calendar
-
To set time and calendar, press B in the regular timekeeping mode.
-
Press the key on a time signal to correct seconds.
-
Press A to move the flashing in the sequence shown below to select the other settings.
-
A numeral can be entered in the flashing position by pressing the required numeral key.
-
Press B to complete setting.
- While setting time and calendar, with every push of , the display is switched between 12-hour and 24-hour formats.
Specifications
Accuracy at normal temperature: ±30 seconds per month average
Display capacity:
x Regular timekeeping
Hour, minute, second, am/pm, year, month, day and day of the week on its
double display
Time format: 12-hour and 24-hour
Calendar system: Auto-calendar pre-programmed from the year 2000 to 2099
x Calculator mode 8 digits (7 digits for negatives)
Abilities: Four basic calculations, chain & mixed operations, constants
for + / – / × / ÷, power calculation
Decimal point: Full floating with underflow
Overflow check: lndicated by the “E” sign, locking the calculator mode
-
Stopwatch mode
Measuring unit: 1/100 second
Measuring capacity: 23 hours, 59 minutes, 59.99 seconds
Measuring modes: Elapsed time, lap time, two finishes -
Dual time mode
-
Alarm mode
-
Hourly time signal
Battery:
One lithium battery (Type: CR2016)
Approx. 5 years operation on type CR2016 (lncludes the alarm for 20 seconds
and calculation for 1 hour per day)
NOTE: THERE IS NO WAY unit components can be damaged or malfunction, due to misoperation of buttons. If confusing information appears on the display it means entry sequence was incorrect. Please read the manual and try again. Specifications are subject to change without notice.
