ERICO CFS303 CADDY Slick Nut Instructions

: June 12, 2024
: ERICO

Table of Contents

CFS303 CADDY Slick Nut
FEATURES
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

INSTRUCTION SHEET

CFS303 CADDY Slick Nut

CADDY® SLICK NUT

To install

ERICO CFS303 CADDY Slick Nut - Nut Install To install With threaded rod

ERICO CFS303 CADDY Slick Nut - Rod See Recomended Torque in table on sheet 2
To remove:

ERICO CFS303 CADDY Slick Nut - Remove

FEATURES

Easy to mount — one hand installation.
No springs or washers required.
Allows threaded rod to be installed after positioning of the CADDY SLICK NUT.
One size fits all strut depths.

WARNING:

ERICO products shall be installed and used only as indicated in ERICO product instruction sheels and training materials. Instruction sheets are availoble at www.erico.com ond from your ERICO customer service representative.
ERICO products must never be used for o purpose other than the purpose for which they were designed or in o manner that exceeds specified load ratings.
Al instructions must be completely followed to ensure proper and sfe installation ond performonce.
Improper installotion, misuse, misapplication or other failure to completely follow ERICO’s instructions and warnings moy cause product malfunction, property damoge, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in o non—corrosive indoor environment.
Al pipe supports, hongers, intermediate components and structural attachments must ONLY be used os described herein and are NEVER to be used for ony other purpose.

NOTE: Al load ratings are for static conditions and do not account for dynamic loading such as wind, woter or seismic loads, unless otherwise noted.
The customer is responsible o. Conformance o all gover b. The integrity of structures to which the products are attached, including their capabilty of safely accepting the loads imposed, as evaluated by o qualiied engineer. c. Using appropriate industry stondord hardware s noted above.
SAFETY INSTRUCTIONS : All governing codes and requlations and those required by the job site must be observed. Aways use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the opplication.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON ore registered trademarks of ERICO International Corporation. ERICO CFS303 CADDY Slick Nut -
Size

Part Number| Article Number| Thread Size| A
Torque| Recommended| Fl
---|---|---|---|---|---
in| mm| ft—lb| N—m| lbs| N
SLICK250| Not
Applicable| 1/4″| Not
Applicable| 4| 6| 400| 1800
SLICK375| 3/8″| 10| 14| 600| 2700
SLICK500| 1/2″| 10| 14| 600| 2700
SLICKM6| 174460| M6| 4| 6| 400| 1800
SLICKM8| 174340| M8| 6| 8| 600| 2700
SLICKM10| 174350| M10| 10| 14| 600| 2700
SLICKM12| 174550| M12| 10| 14| 600| 2700
SLICKM8050| 174360| M8| 1.30| 33.0| 6| 8| 600| 2700
SLICKM8070| 174370| M8| 2.| 53.0| 6| 8| 600| 2700
SLICKM8090| 174380| M8| 3.| 73.0| 6| 8| 600| 2700
SLICKM10050| 174410| M10| 1.30| 33.0| 10| 14| 600| 2700
SLICKM10070| 174420| M10| 2.| 53.0| 10| 14| 600| 2700
SLICKM10090| 174430| M10| 3.| 73.0| 10| 14| 600| 2700