realme RMP2106/WiFi Pad Mini User Manual
- June 4, 2024
- realme
Table of Contents
RMP2106/WiFi Pad Mini
3.1’$$8J’JYNNH
H
,
realme Pad mini
User Manual (RMP2106/WiFi)
xxx-xxxxxx-xxx
REV.1.0
Read this user manual carefully before using the product, and store it in a safe place.
Greetings from realme Pad mini
This manual will show you how to use the pad and its important
information about the pad.
Volume button USB-C connector Headset connector Touch screen
Power button Microphone TF card tray
Speaker Rear camera Front camera
Warning
· Do not place the tablet or battery near or inside heating equipment, cooking
equipment, high pressure vessels (such as microwave ovens, induction cooker,
electric oven, heater, pressure cooker, water heater, gas stove, etc.) to
prevent the battery overheating which may lead to an explosion.
· The original charger, data cable and battery shall be used. Unapproved
charger, data cables, or batteries that are not certified by the manufacturer
may result in electric shock, fire, explosion, or other hazards.
· When charging, please place the device in environment that has a normal room
temperature and good ventilation. It is recommended to charge the device in an
environment with temperature ranging from 5¥~35¥.
· The battery can not be removed from the device, if you need to replace,
please contact realme Authorized Service Center.
Standard accessories
You are provided with the following standard accessories: Pad x 1, Charger x
1, Data Cable x 1, User Manual x 1, SIM Pin x 1.
Specification
Product Main screen parameter Dimension Battery
Camera Operating temperature SAR Values FCC SAR
RMP2106
22.09cm (8.7″)
211.8 x 124.5 x 7.6 mm
6260mAh/24.22Wh(Min) 6400mAh/24.76Wh(Typ) Rear 8Megapixels Front 5Megapixels
0¥~35¥ X.XXW/KGcBody
Radio Bluetooth 2.4G Wi-Fi
5G Wi-Fi
Radio Waves Specifications Frequency 2.4 ~ 2.4835GHz 2.4 ~ 2.4835GHz 5.15 ~5.35GHz 5.47 ~5.725GHz 5.725 ~ 5.85GHz
Max. Output Power 11.36dBm(EIRP) 19.36dBm(EIRP) 17.72dBm(EIRP) 19.24dBm(EIRP) 18.81dBm(EIRP)
This user manual provides the product safety information. Before using the
tablet, please read the Safety Guide carefully.
Statement
The User Manual contains information regarding safety, operation and customer
service. Before using the realme Tablet, please read all the instructions and
the security information below, and keep it for backup. More detailed
instructions are kept in this product as an electronic file. Please read the
built-in instructions on the realme Tablet. For the latest information, please
visit https://www.realme.com.
Security information
This tablet is suitable for working in an environment of 0°C to 35°C.
Temperature for storage should be between -20°C and 45°C.
even damage the tablet and battery. When using this tablet, please
machines. Please charge this tablet in an environment between 5°C and 35°C, so
as not to reduce battery performance and standby time. If the tablet has a
flash charging function, it may not be able to enter the flash charging mode
when the temperature is below 15°C or over 35°C.
the user rooted the ROM system of any third party or modified the system file
by cracking, it may lead to security risks of the system. realme will not
provide any support nor take any responsibility for the final use in these
cases.
Battery precautions in use
1. Please do not weld battery terminals. Otherwise, it may cause battery
leakage, overheat, explosion and fire. 2. Please do not press or pierce the
battery with hard objects (for example needle or other sharp objects), to
avoid damage, battery leak, overheating or fire.
3. Battery liquid may be harmful if contacted with skin or clothes, your skin
might be hurt. Please immediately wash it with water, or go to hospital at
once to seek medical help if necessary. 4. If there are any abnormalities like
high temperature, discoloration, distortion, bulging, leakage, etc. during
operation, charging or preservation, please cease to use the device. 5. Do not
expose the battery liquid to eyes. It might cause potential blindness. When
happens, wash your eyes immediately or go to the hospital if serious. 6. Do
not disassemble or modify the battery, as it may cause battery leakage,
overheating, explosion or fire. 7. Do not place or use the battery near fire,
heater or other high temperature places. Otherwise, it may cause battery
leakage, overheat, explosion or fire. 8. If there is battery leakage or
strange smell, please immediately move it from open flame in order to avoid
fire or explosion. 9. Please keep the battery away from moist or wet areas
from moisture. Otherwise, it may cause battery overheat, fuming and corrosion.
10. Do not place the battery directly in sunlight, or other high temperature
areas. Otherwise, battery leakage and overheating may
battery in a well-ventilated area. 11. Do not use the battery or connect it
with a high-voltage power supply, otherwise it may cause a short circuit or
burst. 12. The battery can be charged and discharged hundreds of times at
least, but it will eventually wear out. 13. Do not dispose the battery as
household waste. Dispose the battery according to local regulations. Caution:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the user manual.
Warning: Please do not charge the battery over 12 hours.
Other matters of attention
1. Adapter shall be installed near the equipment and shall be easily
accessible. 2. If any part of the product is cracked or damaged, discontinue
use immediately and contact the realme Service Center.
To prevent possible hearing damage, do not listen at high volume levels for
long periods.
Waste Electrical and Electronic Equipment (WEEE)
This symbol means that according to local laws and regulations your product
and/or its battery shall be disposed of separately from household waste. When
this product reaches its end of life, user has the choice to give his product
to a competent recycling organization. Proper recycling of your product will
protect human health and the environment.
· realme will seek shared responsibility and cooperation from customers in
reducing the environmental impact of their products.
· realme will comply with all the applicable laws related to WEEE management.
EU Declaration of Conformity (DoC)
Hereby, Realme Chongqing Mobile Telecommunications Corp., Ltd. declares that
this wireless device is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EUThe full text of the EU
declaration of conformity is available at the following internet address:
https://www.realme.com/global/support/eu-declaration.
CE certification information (SAR)
This device was tested for typical body-worn operations with the back of the
tablet kept 0.5cm away. To maintain compliance with RF exposure requirements,
use accessories that maintain a 0.5cm separation distance between the user’s
body and the back of the tablet. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply with RF
exposure requirements, and should be avoided.
If you are using pacemaker, hearing aid, cochlear implant or other device,
please use the tablet according to the doctor’s advice.
Notice: Observe national and local regulations where the device is used. This
device may be restricted for use, depending on the local network. The
operation frequency in 5150-5350MHz of Wi-Fi 5G are restricted to indoor usage
only.
Please check Radio Waves Specifications in the user manual to see whether this
product supports Wi-Fi 5G or not.
FCC Regulations:
This tablet complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. (2) this device must accept any interference received, including
interference that may cause undesired operation.
This tablet has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: · Reorient or relocate the receiving antenna. ·
Increase the separation between the equipment and receiver. · Connect the
equipment into an outlet on a circuit dierent from that to which the receiver
is connected. · Consult the dealer or an experienced radio/TV technician for
help.
FCC Note:
Caution: Changes or modififications not expressly approved by the party
responsible for compliance could void the user`s authority to operate the
equipment.
RF Exposure Information (SAR)
This tablet is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the United States.
During SAR testing, this device was set to transmit at its highest certifified
power level in all tested frequency bands, and placed in positions that
simulate RF exposure in near the body with the separation of 0 mm. Although
the SAR is determined at the highest certifified power level, the actual SAR
level of the device while operating can be well below the maximum value. This
is because the Tablet is designed to operate at multiple power levels so as to
use only the power required to
reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. The exposure standard for wireless
devices employing a unit of measurement is known as the Specifific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. This device is complied
with SAR for general population /uncontrolled exposure limits in ANSI/IEEE
C95.1-1992 and had been tested in accordance with the measurement methods and
procedures specifified in IEEE1528. The FCC has granted an Equipment
Authorization for this tablet with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR information on this tablet
is on fifile with the FCC and can be found under the Display Grant section of
www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2AUYFRMPXXXX For this
device, the highest reported SAR value for usage near the body is XXX W/kg.
While there may be dierences between the SAR levels of various tablets and at
various positions, they all meet the government requirements. SAR compliance
for body-worn operation is based on a separation distance of XX mm between the
unit and the human body. Carry this device at least XX mm away from your body
to ensure RF exposure level compliant or lower to the reported level. To
support body-worn operation, choose the belt clips or holsters, which do not
contain metallic components, to maintain a separation of XX mm between this
device and your body. RF exposure compliance with any body-worn accessory,
which contains metal, was not tested and certifified, and use such body-worn
accessory should be avoided.
Regulatory
Steps to search E-label : Go to Settings -About tablet – Regulatory.
Product Warranty Information I. Service Terms
Thank you for using realme tablet. We will provide our product with
comprehensive warranty services in accordance with applicable national laws
and regulations. In case of any conflict between the following policies and
the National Policies, or Commissions, the national policies shall prevail.
1. Within 12 months from the purchasing date, in the event that performance
failure occurs from normal use, consumer can claim for maintenance. The
accessories such as charger, data cable have a 6-month warranty. The battery
(including internalbattery) has a 12-month warranty. 2. Please ask the dealer
to issue an invoice and keep it in a safe to avail warranty services. 3. Valid
purchase invoice: the invoice shall indicate the serial number of the tablet,
factory serial number (batch number) of the accessories (battery and charger),
product model, sales date, Seller’s seal, amount and so on. 4. A valid invoice
are essential for protecting your warranty rights. (Valid invoice: the
information filled in shall be complete, true and correct without alteration).
If you lose the valid invoice and are unable to provide us with a photocopy of
them, we will provide your tablet with a 12-month warranty. 5. Our warranty
does not cover the other accessories for the product (for instance: the user
manual, warranty card, etc).
Note: The above warranty is only valid for the products sold in this country.
realme have the right of final review and interpretation for the warranty
policy.
II: Warranty Instructions and Conditions
1. Your warranty (please refer to the Warranty Information Card) is only
valid under normal use of your device. All man-made damages and any of the
following conditions are out of free warranty, but a repair can be still
implemented at your own cost:
A. The warranty period has expired; B. Damage caused by human factors,
including damages caused by usage under improper operating environment and the
failure to the user manual; C. The customer disassembles, repairs or modifies
the device without the Company’s authorization or has it repaired at a repair
shop that is not included in the Company’s approved repair network; D. Damage
caused by a force majeure (such as floods, fires, earthquakes and lightning);
E. The user is unable to provide valid proof of purchase or the product model
and barcode do not match or are altered. F. Natural wear and tear of the
product (such as casing, keypad, display screen, antenna and other
accessories). G. Faults, damages or defects not caused by the company; H.
Barcode and warranty labels are damaged and unrecognizable.
2. Others A. External damages(including wear, tear, and scratches) are not
entitled to the warranty service; B. Faults caused by the Internet and
wireless information service providers (operators) are not covered by the
warranty; C. Our warranty does not cover services verbally promised by the
dealer which violate principles set forth on the warranty card. For products
that meet the replacement requirements, you can visit to our nearest
Authorized Service Centre for replacement. Upon replacement, if the device is
faulty, we can replace it with a device of the same specification and model;
if any accessory is faulty, the faulty accessory will be replaced. Both
replacements are free of charge.
3. If any of our products is required to be fixed, you may take it to any
realme Authorized Service Center.
4. If the product requires repair since water enters the device or it is
seriously damaged by human factors, the customer needs to sign the repair job
sheet form with the realme Authorized Service Centre firstly;
5. All components, parts and accessories replaced during the warranty period
shall become the property of the Company.
III: Considerations for Sending the Device for Repair and Collecting It
1. When completing the realme tablet Repair Form, the customer must fill in
valid information in clear handwriting as required (name, address, phone
number and fault symptoms); 2. Before sending your device for repair, please
back up all information and data you have saved on the tablet (such as phone
numbers, text messages and pictures) before you delete them to prevent loss or
damage during the testing and inspection process. In any
responsible or obligated to back up or recover your information and data, or
accept responsibillty for any consequence arising from the loss, damage or
leakage of your information and data. Please ensure the legality of the
information and data you have saved. To respect your privacy, we will not
transmit, backup or examine your information and data(unless they are
necessary for us to provide you with services), and we reserve the right to
refuse to provide services for illegal content; 3. The Customer shall collect
the tablet by presenting the realme tablet Repair Form. In case the Customer
loses the Customer Copy, the Customer shall go through the loss reporting
procedures with his/her personal ID or valid proof of identity before
collecting the tablet.
WARRANTY CARD (Stub Copy)
Respectable customer, This warranty card is your proof of applying for
warranty in the future, Please cooperate with the seller to fill in and keep
it properly for future use!
Name
User
Address
Information Moble No.
Product Name
Product Information
Product Model
Product SN
Vendor Company Name
Address
Vendor Information
Moble No.
Sales date
Invoice number
remark
WARRANTY CARD (Customer Copy)
Respectable customer, This warranty card is your proof of applying for
warranty in the future, Please cooperate with the seller to fill in and keep
it properly for future use!
Name
User
Address
Information Moble No.
Product Name
Product Information
Product Model
Product SN
Vendor Company Name
Address
Vendor Information
Moble No.
Sales date
Invoice number
remark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>