Standard Horizon CMP31 RAM3+ Remote Control Owner’s Manual

Standard Horizon CMP31 RAM3+ Remote Control

The RAM3+ (CMP31) allows you to remotely control all functions of Standard Horizon fixed-mount VHF radios which include GX1600, GX1700, GX2000, GX2100, GX2150, GX2200, and GX5500S. The full dot matrix display and programmable keys make operation simple and fast. Additional features include turning the ra-dio on/off and all DSC functions including Distress. The RAM3+ (CMP31) can be extended up to 70 feet using the optional CT-100 (23 Foot) extension cable. The RAM3+ (CMP31) is backed by an industry-leading 3-year waterproof warranty.

Owner’s Manual

The details of the installation and operation of the RAM3+ (CMP31) are included in the owner’s manual of the compatible fixed mount radio, or it can be downloaded at www.standardhorizon.com. If you have any questions or comments, please contact Standard Horizon Marine Product Support at 800/767-2450.

RAM3+ (CMP31) INSTALLATION

WARNING: Do not connect or remove the CMP31 (RAM3+) microphone while the radio is powered on. This may result in equipment failure.

1. Connect the Extension Cable to the 8-pin connector on the transceiver’s rear panel, then tighten the Cable Nut (Figure 1).
2. Referring to Figure 2, attach the supplied ferrite core as close as possible to the MIC plug of the Routing Cable and External Speaker Connections, then snap its two halves together. And then, wind some plastic tape around the ferrite core, to prevent vibration from causing the two halves to split apart and fall off the wires.
3. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall then insert the Exten-sion Cable into this hole. Connect the Gasket and Mount Base to the Extension Cable Connector using the Nut.
4. Drill the four Screw holes (approx. 2 mm) on the wall then install the Mounting Bracket to the wall using four screws.
5. Put the Rubber Cap on to the Nut.
6. The installation is now complete. Connect the RAM3+ (CMP31) to the Extension Cable Connector and tighten the Cable Nut.

NOTE

• Caution!: Before cutting the cable, it must be disconnected from the rear panel of the transceiver.
• The routing cable can be cut and spliced, however, care needs to be taken when reconnecting the wires to ensure water integrity.
• After cutting you will notice there are the following wires: Yellow, Green, Brown, Purple, Blue, Green, Red, and Shield The Red and Shield wires are wrapped in foil. Remove the foil, and separate the Red and Shield wires.

INCLUDED ACCESSORIES AND REPLACEMENT PART NUMBERS

1. 23-Foot Routing Cable (S8101512)
2. Rubber Cap (RA052520A)
3. Mounting Bracket (RA0525100) & Screws (U24312020 x 4 pcs)
4. Microphone Hanger (RA0458800: Black or RA0436000: White) & Screws (U40412220 x 2 pcs)
5. Ferrite Core (L9190198 or L9190192)

Disposal of your Electronic and Electric Equipment

Products with the symbol (crossed-out wheeled bin) cannot be disposed of as household waste. Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste byproducts. In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

• YAESU MUSEN CO., LTD.
  Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan

• YAESU USA
  6125 Phyllis Drive, Cypress, CA 90630, U.S.A.

• YAESU UK
  Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.

OPTIONAL ACCESSORIES

SPECIFICATIONS

• Supply voltage: 13.8 VDC (Supplied from the transceiver)
• Current consumption: 700 mA @VOL Max. 200 mA @AF Mute
• Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C)
• MIC. Sensitivity (Typical): 60 mVrms @ 1 kHz Tone with 3 kHz Deviation MIC. Impedance: 2 k
• AF output: 800 mW @ 8 for 10 % THD (Internal Speaker) 3 W @ 4 for 10 % THD (External Speaker)
• Display Size: 1.8” x 0.9” (45 x 23 mm)
• Display Resolution: 132 x 64 dot
• Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
• Weight (Approx): 12.9 oz (365g)

RAM3+ (CMP31) CONTROLS

1. [H/L] Key
   Press this key to toggle the transmit power between high and low. When the [H/L] key is pressed while the transceiver is on channel 13 or 67, the power will temporarily switch from LOW to HI power until the PTT is released. The [H/L] key does not function on transmit inhibited and low power only channels.

2. PTT (Push-To-Talk) Key
   Press this key to activate the transmission.

3. POWER ( ) Key
   Press and hold down this key to turn to the transceiver and RAM3+ (CMP31) “on” and “off”.

4. Microphone
   The internal microphone is located here.
   When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from
   the small mic hole. Speak slowly and clearly into the microphone.

5. DISPLAY
   Channel display.

6. SOFT KEY
   For details, refer to owner’s manual of the transceiver.

7. KEY PAD

   • [CALL/MENU] Key
     Press this key to access the DSC OPERATION menu.
     Press and hold this key to access the SETUP menu.

   • [16/9] Key
     First press: channel 16 is immediately selected.
     Second press: recalls the last selected channel.
     Press and hold: selects channel 9.

   • / Key
     These keys are used to select channels, adjust the volume and squelch level, and to choose DSC calls, DSC setup and Radio setup function.

   • [VOL/SQ] Key (Volume Control / Squelch Control)
     Press this key to toggle the function of the microphone’s [ ] or [ ] key between the channel selections, volume level adjustment, and squelch level adjustment.

   • [CLR/WX] Key
     For details, refer to owner’s manual of the transceiver.

   • [ENT] Key
     This key functions as the enter key.

8. Speaker
   The internal speaker is located here.

9. [DISTRESS] KEY
   This key is used to send a DSC Distress Call. Lift the red spring loaded DISTRESS cover, then press and hold in the [DISTRESS] key.

Declaration of Conformity

• Type of Equipment: Remote Station Microphone
• Brand Name: STANDARD HORIZON
• Model Number: CMP31
• Manufacturer: YAESU MUSEN CO., LTD.
• Address of Manufacturer: Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa, Shinagawa-ku,Tokyo 140-0002 Japan

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The technical documentation as required by the Conformity Assessment procedures is kept at the following address:

• Company: Yaesu U.S.A.
• Address: 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
• Telephone: 714-827-7600

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this device not expressly approved by YAESU MUSEN could void the user’s authorization to operate this device.

Yaesu UK Ltd Unit 12, Sun Valley Business Parl< Winnall Close Winchester SO23 OLB United Kingdom

Tel: +44 (0)1962 866667
Fax: +44 (0)1962 856801
Email: sales@yaesu.co.uk

Declaration of Conformity

Nr. YUK-DOC-1103-15

We, Yaesu UK Ltd. certify and declare under our sole responsibility that the following equipment complies with the essential requirements of the Directive 1999/5/EC and 2011/65/EU.

• Type of Equipment: Remote Station Microphone
• Brand Name: STANDARD HORIZON
• Model Number: CMP31
• Manufacturer: YAESU MUSEN CO., LTD.
• Address of Manufacturer: Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa, Shinagawa-ku,Tokyo 140-0002 Japan

Applicable Standards:

This equipment is tested to and conforms to the essential requirements of directive, as included in following standards:

The technical documentation as required by the Conformity Assessment procedures is kept at the following address:

• Company Address Yaesu UK Ltd Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire UK SO23 0LB

Technical Construction file

• Issued by: Yaesu Musen Co. Ltd, Tokyo Japan
• File No: YETA00154B
• Drawn up in: Winchester, Hampshire UK
• Date: 2nd November 2015

Signed for and on behalf of Yaesu UK Ltd

Name and position: PCJ Bigwood Technical Sales Manager

FREQUENTLY ASKED QUESTIONS

What is the Standard Horizon CMP31 RAM3+ Remote Control?

The Standard Horizon CMP31 RAM3+ Remote Control is a remote control unit designed for use with Standard Horizon marine radios.

What marine radios is the CMP31 RAM3+ compatible with?

The CMP31 RAM3+ is compatible with select Standard Horizon marine radios, such as GX6000, GX2400, GX2200, GX2000, GX1850, and GX1800.

What functions can I control with the CMP31 RAM3+ Remote?

The CMP31 RAM3+ allows you to control various functions of the compatible marine radio, including channel selection, volume, squelch, and DSC (Digital Selective Calling) functions.

How is the CMP31 RAM3+ Remote Control connected to the marine radio?

The CMP31 RAM3+ connects to the marine radio using a standard 6-pin communication cable.

Is the CMP31 RAM3+ waterproof?

The CMP31 RAM3+ Remote Control is water-resistant, designed to withstand marine environments, but it should not be submerged in water.

Can I use multiple CMP31 RAM3+ remotes with one marine radio?

In most cases, you can use multiple CMP31 RAM3+ remotes with one compatible marine radio, allowing control from different locations on the boat.

Does the CMP31 RAM3+ Remote require its power source, or does it draw power from the marine radio?

The CMP31 RAM3+ draws power from the connected marine radio. It does not require a separate power source.

Can I use the CMP31 RAM3+ Remote Control as a wireless remote?

The CMP31 RAM3+ is not wireless and requires a wired connection to the compatible marine radio.

Does the CMP31 RAM3+ have a display screen?

Yes, the CMP31 RAM3+ features a backlit dot matrix display for easy visibility and control.

Can I mount the CMP31 RAM3+ Remote Control on the boat's steering wheel?

Yes, the CMP31 RAM3+ is designed for versatile mounting options, including on the boat's steering wheel or other locations on the boat.

Does the CMP31 RAM3+ have a built-in speaker for audio output?

Yes, the CMP31 RAM3+ features a built-in speaker for audio output, allowing you to hear communications directly from the remote.

Does the CMP31 RAM3+ Remote Control support DSC calling?

Yes, the CMP31 RAM3+ supports DSC (Digital Selective Calling) functions, which is a feature of compatible Standard Horizon marine radios.

How do I set up and pair the CMP31 RAM3+ Remote with the marine radio?

The CMP31 RAM3+ typically connects to the compatible marine radio through a 6-pin communication cable, and the pairing is established through this connection.

Can I use the CMP31 RAM3+ Remote Control with a handheld marine radio?

The CMP31 RAM3+ is designed for use with fixed-mount marine radios and may not be compatible with handheld radios.

What is the range of the CMP31 RAM3+ Remote Control?

The range of the CMP31 RAM3+ remote is determined by the length of the 6-pin communication cable connecting it to the compatible marine radio.

DOWNLOAD THE PDF LINK:Standard Horizon CMP31 RAM3+ Remote Control Owner’s Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>