BDE Technology Inc BDE-MP2652P7 Wireless Module User Guide
- June 12, 2024
- BDE Technology Inc
Table of Contents
BDE-MP2652P7 USER GUIDE
Wireless Module
User Guide
BDE-MP2652P7 USER GUIDE
Introduction
This user guide is for BDE-MP2652P7, a Wireless Module based on TI CC2652P7.
It is a quick start guide for how to connect the module with the evaluation
board BDE-EVB07 or with the TI launchpad, and how to build the first
application. It also shows a demo for how BDEMP2652P7 receives a data packet
that is sent from the mobile terminial.
Hardware Diagram
A. Block Diagram
B. RF Switch True Table
Table 4. SKY13317-373LF Truth Table
Low Insertion Loss Path | V1 (Pin 3) | V2 (Pin 6) | V3 (Pin 7) |
---|---|---|---|
RFC to RF1 | High | Low | Low |
RFC to RF2 | Low | High | Low |
RFC to RF3 | Low | Low | High |
Note: “High” = 1.8 to 5.0 V. “Low” = 0 to 0.25 V. Any state other than
described in this Table places the switch into an undefined state. An
undefined state will not damage the device.
C. Antenna Selection Schematic
The module is using the switch to select 5 dBm or 20 dBm TX power and also the
RX path for the 2.4-GHz band. Sub-1GHz band is standalone for having its own
antenna.
Wireless Module
Get Ready
The following tools are recommended to develop with BDE-MP2652P7.
Hardware tools:
- BDE-MP2652P7 BDE-MP2652P7-BDE Technology Inc. (bdecomm.com))
- Two BDE-ADP208 V1.0 (adaptor board)
- PC or Laptop
- A BDE-EVB07 ( BDE-EVB07-BDE Technology Inc. (bdecomm.com))
- USB cable for power supply and debugging
Software tools:
- Terminal software such as CCS, IAR.
Wireless Module
- CCS download
- Software Development Kit (SDK)
- nRF Connect
Build Your First Application
Once have the Hardware and Software tools in place, please following the
following steps:
A. Connect the Hardware
If chose EVB07:
Use USB cable to connect EVB07 and PC or laptop. Plug BDE-MP2652P7 with the
adaptor board into the dev board and connect all the pins with Jumpers as the
following picture shows.
B. Build the Application
-
Download and install the CCS and SDK
From the above links, follow the instructions in the following steps to download and install the CCS and SDK. -
CCS Installation
- Click on this option
- Select an option to download CCS
- Unzip the package to a local disc
- Click the setup of CCS
- Click “Next”
- Select the default option
- Click “Next”
- Select the Installation Directory
- Select the default option
- Select the component
- Select the default option
- Click “Next”
- Click “Next”
- Waiting for installation to complete
Software Development Kit (SDK) installation
- Click on this option
- Select an option you need to download SDK
- Log in to your TI account, if you are a new user, register a TI account first
- Select “civil” if your application is for civil use
- Select “Yes” and submit
- Download SDK
- Installation
- Click “Next”
- Select the default option
- Select the Installation directory
- Click “Next”
- Waiting for installation to complete
Run an example/demo code
-
For the first module, find the option named “Import CCS project…”
-
According to the following path to find the sending end project: ti\simplelink_cc13xx_cc26xx_sdk_6_40_00_13\examples\rtos\LP_CC135 2P7_4\ble5stack\simple_peripheral
(Since TI does not have a dedicated SDK for CC2652P7, we use LP_CC1352P7_4 instead, which can also run normally on CC2652P7 devices) -
Open the file: simple_peripheral.syscfg
-
Chang the “0xC1” to “0x00”.
-
Right Click the project to build the receiving end project
-
Click this bug icon (means download and debugging)
-
C lick on this option to start debugging
-
Download and start nRF Connect (an APP on your mobile device)
-
BDE-MP2652P7 is advertising, you can receive the signal on nRF Connect, then click “connect” to connect the mobile phone and the BDE-MP2652P7.
-
Find the file which is named “simple_gatt_profile.c” and the function which is named “simpleProfile_WriteAttrCB”
-
Find “pValue” in the function and set a breakpoint at the same line
-
Click the up arrow to send a message to the BDE-MP2652P7
-
Send 0x11 to the BDE-MP2652P7
-
The program stops at the breakpoint, the value received is 0x11
By far you should’ve built your first application successfully.
For further development, please check out the CC2652P7 datasheet, product
information and support | TI.com page and download the User
guide
Other Resources
Windows Installer for SimpleLink CC13XX CC26XX SDK
Linux Installer for SimpleLink CC13XX CC26XX SDK
Mac OS Installer for Code Composer Studio IDE
Linux Installer for Code Composer Studio IDE
Windows Installer for SmartRF Flash Programmer 2
More Questions:
Please search existing answers on TI E2E support forums
Contact your local TI sales representative.
Or Contact BDE Technology, Inc.
China: B2-403, 162 Science Ave, Huangpu District, Guangzhou, 510663
Tel: +86-020-28065335
Website: http://www.bdecomm.com/cn/
Email: shu@bdecomm.com
USA: 67 E Madison St, #1603A, Chicago, IL 60603
Tel: +1-312-379-9589
Website: http://www.bdecomm.com/
Email: info@bdecomm.com
BDE Technology Inc
info@bdecomm.com
References
- BDE Technology Inc.
- BDE Technology Inc.
- 广州碧德科技股份有限公司
- BDE-MP2652P7(Multi-Protocol with PA Based on CC2652P7) -BDE Technology Inc.
- Log in | myTI | Texas Instruments
- TI E2E support forums
- nRF Connect for Mobile - nordicsemi.com
- CC2652P7 data sheet, product information and support | TI.com
- CCSTUDIO IDE, configuration, compiler or debugger | TI.com
- FLASH-PROGRAMMER Software programming tool | TI.com
- SIMPLELINK-LOWPOWER-SDK Software development kit (SDK) | TI.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>