Hipeak B0C9JF5WHS 750W Electric Bike for Adults User Guide

Changzhou Gaide Intelligent Technology Co.,Ltd

Manual

GD01 Ebike Intelligent Display

Address: NO.202 Tanggoutou Road , Yaoguan Town, Jingkai District, Changzhou city, Jingsu Province
Website: www.czgaide.com

1. Material & Dimension

1. Material
   Caser and Cover and Press button: ABS,
   LCD window: PMMA

2. Outside and mounting dimension (mm)

3. Installation

• Install the display in the middle of handlebar, then adjust to suitable angle, install the press button to left side of handlebar.
• Power off the device, connect the device to controller.
• Power on

2. Overview of GD01

1. UART protocol:
   Equipped with independent press buttons
2. Speed:
   Real-time SPEED
3. kmh/mile:
   Kmh/MPH according to habit
4. Battery level:
   Indicates the battery level in real time
5. Head light control:
   Press + button for 3 seconds to power on/off
6. Back light adjustment:
   3-level adjustment
7. Assist level:
   From P to 7, press button to change assist level.
8. Distance:
   ODO/Trip/Driving duration
9. Error code:
   Please refer to appendix table 1 for definition
10. 6km mode:
    In this mode, it will display on the screen
11. Parameter setting:
    Set parameters, such as: wheel size, speed limit etc

3. Presentation of screen

1. Battery level: 5 levels, voltage interval could be customized
2. Speed: Average SPEED/MAX SPEED/Real-time SPEED
3. Speed unit: Kmh/MPH
4. 6km mode: 6km mode Display .
5. Assist level: actual assist level P~7.
6. Head light icon: indicates when head light and back light are on.
7. Distance: Trip/ODO.
8. Error code: “ERR” and code when there is error

4. Press button definition

GD01 uses independent press button, in total three buttons:

+ “UP” M “Power” – “DOWN”

5. Operation instructions

1. Power ON/OFF
   When the power is off, Long press M (Power) during 3seconds, screen will display all contents and start to normal working mode, and controller will be turned on When the power is on, Long press M (Power) during 3 seconds, screen will be powered off, and controller will be turned off . If no any operation both on bike and display during 10 minutes (time could be set), the display will turn off automatically , in this case, no power consumption for both display and controller.

2. Different Speed display:
   Long press + and M o switch different speed information, Real time speed (SPEED)

3. ODO/TRIP/ Driving Time/Error Code
   Short press M to switch ODO/TRIP/ Driving Time/Error Code ODO (Accumulated distance)→Trip(Single trip distance)→TM(Driving Time)→ERR(Error Code).

4. Assist level
   Short press + or – to change assist level, default value is level 1

5. Head light control
   Long press + for 3 seconds turn on/off the head light.

6. 6km mode
   When the bike is stopped, long press – , will enter 6km/h mode, the speed will be 4.5~7.5km/h according to different road conditions, “ ” will show up on screen, long press – again or short press – ，will quit 6km/h mode. Long press or short press could be customized by clients.

6. Parameter setting

When the display is powered on, long press + and – , will enter parameter setting mode,  in this mode, can change parameter values,  long press again + and – will quit parameter setting mode or no operation during 10s will also quit this mode.
In parameter setting mode, short press + / – will change parameter value, short press M will save current value and switch to next parameter.

1. P01-back light lightness：
   short press + / – will switch from 1 to 3, Level 3 is lightest. Level 2 is default value.

2. P02-kmh/MPH：
   Short press + / – to Switch kmh/MPH.

3. P03-Working voltage：
   short press + / – to switch 24V,36V,48V, Default value is 36V.

4. P04-Auto shutdown time:
   short press + / – to switch from 0 to 60, it is the time (in minutes) toshut down the screen automatically if no operation 0 means nevershut down, Default value is 10 minutes

5. P05-Number of Assist levels：
   Display level 7.

6. P06-Wheel size selection：
   short press + / – to switch wheel size, step： 16 inch, 20 inch, 22inch, 24 inch, 26 inch, 700C, 28 inch.

7. P07-Number of magnets for speed sensor：
   short press + / – to switch fromt 1 to 15.

8. P08-speed limit：
   short press + / – to set the speed limit from 10 to 41km/h.

9. This feature is reserved: display P09, invalid.

10. This feature is reserved: display P10, invalid.

11. P11-assist sensitivity setting：
    short press + / – to switch from 1 to 24.

12. P12-assist starting power setting:
    short press + / – to switch from 0 to 3.

13. P13-Assist magnetic disc types
    short press + / – to switch from 5->6->8->10->12 ，different numbers of magnets.

14. P14-Current limit for the controller：
    short press + / – to switch from 1 to 20A

15. This feature is reserved: display P15, invalid.

16. P16-Reset ODO distance: long press + during 5 seconds.

17. P17-The signal direction of the booster sensor: short press + / – to switch from 0 to 1; 0: Booster signal; 1 Power signal negative.

18. P18-Shift gears with gear: short press + / – to switch from 0 to 1; 0: Don’t shift gears; 1: Shift gears.

19. P19- Throttle the 6KM function: short press + / – to switch from 0 to 1; 0: Turn to the normal; 1: Throttle 6Km.

7. Specifications

1. Power supply: 24V, 36V, 48V
2. Rated current: 10mA
3. Max current: 30mA
4. Leakage current after power off: <1uA
5. Current supply to controller: 50mA
6. Working Temperature: -18~65
7. Storage temperature: -30~80

8. Error code definition

When an error appears, GD01 will notice users by different codes, please refer to table 1 for different codes:

Code (Decimal)

| Signification
---|---
0|

Normal

6

| Low Battery level
30|

Communication failure

21

| current sensor fault
22|

Throttle failure

23

| Failure of motor phase line
24|

Motor hall failure

25

|

Brake abnormity

Table 1

9. Notices

Power on and power off must keep an interval of at least 3 seconds, please don’t press “ M ” button frequently when it is powered off.
When the temperature is under -10°C , the screen will be a little darker than normal, when the temperature increases, the screen can go back to normal

10. FAQ

1. Q Why I can not power off?
   A Please check connection between display and controller.
2. Q What can I do if an error code displays?
   A Find a nearest shop to get repair

11. Warranty

1 year of warranty for quality issue except frame is broken.

12. Version

This is a universal manual for GD01.It could be customized by each client. Please confirm all details before purchasing.

References

• 常州盖德智能科技有限公司

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>