ifi 2A5QJZENONESTU ZEN One Studio Instruction Manual

Instruction Manual

2A5QJZENONESTU ZEN One Studio

Thank you for purchasing the ZEN One Studio. The ZEN One Studio is a Bluetooth, USB, S/PDIF DAC with digital and analogue outputs.

1. Power switch
   Short press to turn on. Long press to turn off.

2. Input selector
   This button cycles through 3 inputs, see item 5 for LED colours.| |
   ---|---|---
   Bluetooth (Blue/Red)| S/PDIF (Green)| USB (Green)

3. Display
   The colour of the ‘iFi’ logo in the center of the front display represents the file format received: LED| Format (Wired/Wireless)
   ---|---
   White| PCM/HWA(LHDC)
   Cyan| DSD/LDAC
   Green| MQA/aptX Adaptive
   Blue| MQA Studio/aptX
   Magenta| Original Sample Rate/aptX HD
   Yellow| AAC
   OFF
   MQB| SBC

4. Audio format and INPUT LED (kHz)
   The LED colour scheme indicates the sampling frequency that the ZEN One Studio receives from the music source.

5. Bluetooth pairing and Display ON/OFF
   1) Pairing (long press)
   After power-on, the ZEN One Studio searches for a previously paired device and flashes blue. If a stored device is not found, it automatically enters pairing mode and flashes between blue and red. The LED switches to blue flashing, and the device cannot be connected automatically after a timeout of 5 minutes.
   To enter pairing mode, press the button for 3 seconds until the light flashes between blue and red. To pair it with your phone or another device, look for ’iFi Hi-Res audio‘ on the list of available Bluetooth devices.
   The ZEN One Studio is able to store up to 8 paired Bluetooth devices. When the 9th device is paired, the oldest device in memory will be deleted.

6. Display screen ON/OFF (short press)
   Turns the display on or off.

7. Balanced 4.4mm fixed level analogue output
   For connection of 4.4mm to XLR or similarly balanced interconnects.
   Warning: Do not insert 4.4mm headphones to this source as the full volume is likely to damage your headphones or your hearing.

8. Digital coaxial input/output
   Input channel selector (item 2) determines the function of digital coaxial connector, which is:
   a) an output when item 2 is on Bluetooth or USB
   b) an input when item 2 is on S/PDIF

9. Balanced XLR analogue output
   This is a balanced analogue output.

10. USB-C input
    This USB-C port is intended for data transfer only, It connects the ZEN One Studio to the audio source.
    Tip: For firmware and driver downloads, please visit: www.ifi-audio.com /download-hub/
    Note: For use with a PC, it is necessary to install drivers.

11. Antenna
    Please attach the enclosed antenna for highest signal quality.

12. Power cable anti-drop pendant
    Used to secure the power cable to prevent the power supply from falling out or coming loose.

13. Power supply LED
    When connected to an external power supply, the light will turn green.

14. DC 5V power
    Please connect the ZEN One Studio to the included power supply. The ZEN One Studio must ONLY be powered by 5 volts.

SPECIFICATIONS

Digital inputs:| USB3.0 Type B (USB2.0 compatible)
S/PDIF (3.5mm coaxial)
Bluetooth 5.1™ (aptX, aptX HD, aptX Adaptive, aptX LL, LDAC, LHDC/HWA, AAC and SBC codec)
---|---
Formats:| DSD 256 / 11.3MHz
PCM 384kHz
MQA Decoder
Bluetooth 96kHz
Chipset:| Bit-Perfect DSD & DXD DAC by Burr Brown
Qualcomm QCC 5100 Series
Analogue outputs:| Coaxial, Audio XLR L/R
4.4mm Balanced line out
Frequency Response:| 5Hz – 80kHz ±3dB
Outputs:| 4V / 2V max. (BAL/UnBAL)
Output Impedance:| ≤72Ω/36Ω (BAL/UnBAL)
SNR:| -105dB(A) @ 0dBFS (BAL/UnBAL)
THD + N:| <0.002% @ 0dBFS(BAL/UnBAL)
Power supply requirement:| DC 5V (centre pin +ve)
Power consumption:| No Signal ~0.7W / Max Signal ~1.0W
Dimensions:| 158 x 100 x 35 mm (6.2″ x 3.9″ x 1.4″)
Net weight:| 500g (1.1 lbs)
Limited Warranty:| 12 months

• 12 months typical or as permitted/required by local reseller laws.
  **Speciation’s are subject to change without notice.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ifi-audio.com
Ver1.0

References

• iFi audio | the Award-Winning Audio Technology Company

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>