FISHER PAYKEL WB76SPEX1 Warming Drawer Installation Guide

June 4, 2024
Fisher & Paykel

FISHER PAYKEL WB76SPEX1 Warming Drawer Installation Guide
FISHER PAYKEL WB76SPEX1 Warming Drawer

SAFETY AND WARNINGS

**WARNING!
Tip Hazard
This product may tip. Keep children away and take care. Failure to follow this advice may result in injury.

**

  • Drawer must be secured in place by supplied screws.
  • Ensure there is a fixed shelf directly above the drawer if it is not installed under another product.

WARNING!
Cut Hazard
Failure to use caution could result in injury.

  • Take care: some edges may be sharp.
  • Do not put fingers in the drawer when closing.

WARNING!
Electric Shock Hazard
Failure to follow this advice may result in electrical shock or death.

  • If the product is damaged, switch the appliance off and disconnect it from the mains to avoid possible electric shock.

WARNING!
Weight Hazard
Failure to follow this advice may result in damage or personal injury.

  • Ensure the bottom shelf of the cabinetry can fully support the weight of combined appliances.

READ AND SAVE THIS GUIDE

WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety guides listed below. Read all the instructions before using the appliance.

Installation

  • Please make this information available to the person installing the product.
  • The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection.
  • Ensure the installation complies with all clearance requirements and applicable standards and regulations.
  • When installed in combination with a companion product, the companion product can be placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be able to support the weight of both products.
  • Ensure the cabinetry is square and level and with correct dimensions.
  • If installing the appliance directly underneath an oven, ensure you do not damage the oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage resulting from incorrect installation.
  • Before installing the appliance, inspect for any signs of damage. Do not install or use damaged appliances.
  • Be careful when stacking the appliances on top of each other to avoid damage to the appliances.

Electrical

  • All connections for electrical power and earthing must be done by a qualified electrician and must comply with local codes and ordinances.
  • Before installation, ensure that the voltage and frequency listed on the data plate corresponds with the household electrical supply.
  • When combining with another appliance, ensure each appliance has its own power outlet. Avoid sharing the power point to prevent accidental switching off of the appliance.
  • Ensure your appliance is properly grounded (earthed).
  • Connect the drawer to a properly rated, protected and sized power supply circuit to avoid electrical overload.
  • Do not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet box) to connect the drawer to the power supply. Ensure the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
  • Ensure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of the centre rear of the product.

Servicing

  • Do not repair or replace any part of the appliance unless specifically recommended in the user guide. All other servicing should be done by a Fisher & Paykel trained and supported service technician or qualified person.
  • Always disconnect the power supply before doing any installation, maintenance or repair work, and cleaning.
  • If the power supply cord is damaged, it must be replaced by a qualified electrician or Fisher & Paykel trained and supported service technician.

PARTS SUPPLIED

  • Service & Warranty

  • User guide

  • Installation guide

  • T20 star head countersunk screw 4×20
    4 for WB30 models
    2 for WB24 models

  • Wire shelf (1)
    For WB30 models only

  • 5mm Hex key

  • Handle

  • Socket screw (2)

TOOLS REQUIRED

T20 star-head screwdriver

UNPACK YOUR PRODUCT

Remove the warming drawer and accessories box from the packaging. Recycle the materials that can be reused. Dispose packaging materials in accordance with local regulations on waste disposal.

Inspect the warming drawer for any signs of damage. Do not install the warming drawer if it has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.
UNPACKPRODUCT

RECYCLE RESPONSIBLY

ELECTRICAL SPECIFICATIONS

All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and supported service technician.

  WB76
Supply 110 VAC, 60 Hz
Service 10 amp circuit
Maximum Power 810 W
Power outlet* 3-prong grounding-type
Power cord (total length) 1800mm
  • The power outlet must be earthed and located within 900mm of the centre rear of the product.

PRODUCT DIMENSIONS

  • PLAN
    PRODUCT DIMENSIONS

  • ISOMETRIC
    PRODUCT DIMENSIONS

  • FRONT
    PRODUCT DIMENSIONS

  • PROFILE
    PRODUCT DIMENSIONS

PRODUCT DIMENSIONS: MM

  • A Overall height: 271

  • B Overall width: 761

  • *C Overall depth:** 567

  • D Height of chassis: 271

  • E Width of chassis: 707

  • F Depth of chassis:** 547

  • G Height of drawer front panel: 267

  • H Depth of drawer front panel and attachment flange: 20

  • I Depth of open drawer: 419

  • J Height from bottom of chassis to bottom of drawer front panel:  2

  • K Width of handle: 736

  • L Depth of handle: 58

  • Including drawer panel and power plug
    ** Including power plug. Excludes attachment flange.

PRODUCT WEIGHT

| KG
---|---
Total weight of drawer*|

34

*including packaging and excluding handle

CABINETRY DIMENSIONS

  • PROFILE
    CABINETRY DIMENSIONS

  • PLAN
    CABINETRY DIMENSIONS

  MM
A Minimum inside height of cavity 273
B Minimum inside width of cavity 720
C Minimum inside depth of cavity 560
D Overall width of cabinetry 762
E Minimum clearance between top of front panel and upper cabinetry panel 3
F Minimum clearance between bottom of front panel and lower cabinetry panel 2
  • FLUSH INSTALL
    FLUSH INSTALL

  • PROUD INSTALL
    PROUD INSTALL

INSTALLATION OPTIONS

STANDALONE INSTALLATION

This installation is suitable for Minimal, Contemporary & Professional Warming drawers. A fixed shelf must be installed above the warming drawer.

  • PROFILE
    STANDALONE INSTALLATION

  • FRONT
    STANDALONE INSTALLATION

COMBINED WITH SINGLE OVEN
  • PROFILE
    COMBINED WITH SINGLE OVEN

  • FRONT
    COMBINED WITH SINGLE OVEN

COMBINED WITH COMPANION PRODUCT

This combination is suitable for 76cm Warming Drawers that can fully support 76cm Fisher & Paykel companion products.

  • PROFILE
    COMBINED WITH COMPANION

  • FRONT
    COMBINED WITH SINGLE OVEN

COMBINED WITH DOUBLE OVEN

This combination is suitable for 76cm Warming Drawers that can fully support a 76cm Fisher & Paykel double oven.

  • PROFILE

  • FRONT
    COMBINED WITH DOUBLE OVEN

TRIPLE STACK COMBINATION

This combination is suitable for Minimal, Contemporary & Professional Warming Drawers. The 76cm model can fully support both 76cm Fisher & Paykel single oven and companion product. A shelf is required above the oven to support the companion product. Ensure the bottom shelf can fully support the weight of all appliances.

  • PROFILE
    TRIPLE STACK COMBINATION

  • FRONT
    COMBINED WITH DOUBLE OVEN

INSTALLING THE DRAWER

  1. Connect the power plug into the power outlet.
    Place the warming drawer carefully inside the cabinetry.
    INSTALLING THE DRAWER

  2. Push the warming drawer back into the cabinetry, and align the front panel with the cabinetry as desired.
    PROFILE
    INSTALLING THE DRAWER

  3. Open the drawer and secure the attachment flanges of the drawer to the side edges of cabinetry with T20 star head machine screws (4x).
    INSTALLING THE DRAWER

ADJUSTING THE DEPTH

The depth of the front panel of the warming drawer can be adjusted to align with the surrounding cabinetry.

  1. Open the drawer fully. Using a hex key, turn the adjustment screw to move the front panel forward. Turn clockwise to move backwards or counterclockwise to move forwards.
    ADJUSTING THE DEPTH

  2. The depth is adjustable within 4mm.

INSTALLING THE HANDLE
  1. Carefully fit the handle onto the mounts.
    INSTALLING THE HANDLE

  2. Insert the socket screws and tighten from the base of the handle using the supplied Allen key. Apply upward pressure to the handle while tightening to reduce the risk of damage.
    INSTALLING THE HANDLE

ADJUSTING THE HEIGHT

The front panel of the warming drawer can be adjusted vertically to align with the surrounding cabinetry.

  1. Open the drawer fully, and slightly loosen the screws.
    ADJUSTING THE HEIGHT

  2. Adjust to the required height and then re-tighten the screws. The height is adjustable within 1/16″ (2mm).
    ADJUSTING THE HEIGHT

  3. Close the drawer and check the alignment. Adjust again if necessary.
    ADJUSTING THE HEIGHT

INSTALLER CHECKLIST

IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use.

Test operation:

  • Open the drawer.
  • Press the button to turn the warming drawer on.
  • Shut the drawer.
  • After 5-10 minutes, open the drawer to feel the internal surfaces of drawer is slightly warmed.
  • Press the button to turn the warming drawer off and shut the drawer.

Ensure that:

  • the warming drawer is level and securely fitted to the cabinetry.
  • any internal packaging has been removed from the drawer,
  • the isolating switch is accessible by the customer.
  • the bottom shelf can fully support the total weight of the combined appliances.

Complete and keep for safe reference:

Model: __
Serial No.: __
Purchase Date: __
Purchaser: __
Dealer Address: __
Installer’s Name: __
Installer’s Signature: __
Installation Company: __
Installation Date: __

© Fisher & Paykel Appliances 2021. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Fisher & Paykel User Manuals

Related Manuals