Arrogant 62725 Zephyr Switch Controller Instruction Manual

Arrogant 62725 Zephyr Switch Controller

Specifications

• Connection:  Bluetooth 2.1 and USB-C
• Wireless distance: up to 8 m
• Charging time: 2 h
• Battery time: up to 12 h
• Cable length:1 m
• USB input:5V/600 mA
• Frequency range: 2402-2480 MHz
• Effective radiated power:0.66 dBm
• In the box: Wireless game controller, USB-C cable, manual

Use

Power on/off
Press any button on the controller to turn it on (excl. left or right joystick). The LED indicators light up. Press the Sync button on the back of the controller to turn it off.
Note! The controller turns off automatically after 5 minutes of inactivity.

Charging the controller
The LED indicators located below the joysticks on the front of the controller rapidly flash to indicate that the built-in battery is low and needs to be charged. Connect the included USB-C cable to the controller’s USB port and a USB charger or computer. The LED indicators below the joysticks flash when the controller is charging and turn off when it has been fully charged. If you want to charge and at the same time use the controller wirelessly connected to a Switch console you need to first enable an option called “Pro controller wired communication” on the Switch. Navigate to the Switch home screen. Open “System settings” and go to “Controllers and sensors”. Enable the “Pro controller wired communication” option.

Connecting to a Switch console

Wireless connection:

1. Navigate to the Home screen on the Switch console. Open “Controllers” and press the “Change grip/order” option.
2. Press and hold the Sync button on the back of the controller for 3-5 seconds. The LED indicators start flashing. Release the Sync button.
3. Follow the on-screen instructions on the Switch console.

Wired connection (only works if Switch is docked)

1. Connect the included USB-C cable to the controller USB port and a
2. The USB port on the dock where the Switch console is mounted. The LED indicators on the controller start flashing.
3. Press any button on the controller (excl. the Turbo button) to connect the controller to the Switch console.

Note! The controller is automatically wirelessly paired to the Switch console if it has first been connected via a USB cable.
If you turn off the controller or Switch console after pairing them wirelessly, you can reconnect the controller by holding the Home button (G) for 3-5 seconds. The LED indicators flash and the controller is automatically reconnected to the Switch console.
You can use the controller to wake a paired Switch console from standby mode. Press and hold the Home button (-Q-) for 2 seconds. The LED indicators start flashing. The Switch console turns on after a 3-second delay and the LED indicators on the controller turn off. Press any button on the controller 3 times (excl. the Turbo button) to unlock the Switch.

Connecting to an Android device

1. Open the Bluetooth settings on your smart device and search for devices nearby
2. Press and hold the Sync button on the back of the controller for 2 seconds, and the LED indicators start flashing slowly. Keep holding down the Sync button and press the Y button for 2 seconds until the second and third LED indicators (from left to right) start flashing. Release both buttons.
3.  Connect to “Gamepad” on your smart device.

Connecting to an iOS device

1. Open the Bluetooth settings on your smart device and search for devices nearby.
2. Press and hold the Sync button on the back of the controller for 2 seconds, and the LED indicators start flashing slowly. Keep holding down the Sync button and press the X button for 2 seconds until the first and fourth LED indicators (from left to right) start flashing. Release both buttons.
3. Connect to the “Xbox Wireless Controller” on your smart device.

Connecting to a PC (wired connection only)

1. Connect the USB-C cable to the controller and a USB port on the PC.
2. The controller is automatically installed as a “Controller” on the PC and the first and fourth LED indicators (from left to right) light up.

This controller supports Xlnput mode and Directlnput mode when connected to a PC. Xlnput is the default mode and the controller automatically starts in this mode. It is designed by Microsoft for their Xbox controllers and is compatible with most platforms on PC. Directlnput mimics the earlier types of controllers for systems such as Nintendo 64 and Nintendo Entertainment System (NES). Press and hold the+ and – buttons to switch from Xlnput to Directlnput mode. The controller is shown as a “Gamepad” on the PC and the second and third LED indicators (from left to right) light up. Press and hold the+ and – buttons to switch to Xlnput mode again. The first and fourth LED indicators (from left to right) light up.

Turbo mode
Turbo is used to send a command automatically and repeatedly while holding down a button. Turbo can be enabled for multiple buttons at the same time.
Note! Turbo mode is compatible with buttons: Y, X, B, A, L 1, ZL, R1, and ZR. Turbo mode is not compatible with:-.+. Capture, Home. the analog stick directions or pad buttons.

To enable turbo mode, press and hold the Turbo button in the middle of the controller while pressing the buttons you want to activate turbo mode for. Release the buttons to confirm. To disable turbo mode on a button, press and hold the Turbo button in the middle of the controller and press the button with turbo enabled twice. To reset all Turbo settings, press and hold the Turbo button in the middle of the controller for 5 seconds.

Changing the speed of the Turbo button presses
To change the speed of the repeats in turbo mode:

1. Press and hold the Turbo button in the middle of the controller.
2. To increase the speed, tilt the right analog stick forward.
3. To decrease the speed, tilt the right analog stick back.
4. Release the Turbo button to confirm your setting.

Note! This setting affects the repeating speed of all turbo-enabled buttons.

Changing the vibration intensity of the controller
The vibration intensity has 4 levels: off, 35 %, 70 %, and 1 DD%.

1. Press and hold the Turbo button in the middle of the controller.
2. To increase the intensity, tilt the left analog stick forward.
3. To decrease the intensity, tilt the left analog stick back.
4. Release the Turbo button to confirm your setting.

Simplified EU Declaration of Conformity

Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at www.kjell.com/62725

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>