PIRAMID 3×3W LED Battery Powered Luminarie User Manual
- June 12, 2024
- PIRAMID
Table of Contents
PIRAMID 3×3W LED Battery Powered Luminarie User Manual
SECURITY TIPS
WARNING!!! To reduce the risk of fire, electric shock, or injury to persons, follow these important safety instructions:
- non-professionals, not to disassemble the light arbitrarily and lighting accessories inside.
- rated voltage range: AC110V-120V/60Hz or AC200V-240V / 50HZ (to be selected).
- not beam irradiate the flammable materials, flammable materials and the lamp should be maintained at least 1M over the distance.
- lamps used in ambient temperature: -15 ℃ -40 ℃, the highest temperature of the surface of the lamp: 60 ℃.
- to keep away from the liquid substance and humid environment.
- before using the lights must ensure the good grounding, can not install charging and remove any parts.
- the installation of lamps, must be fixed screw fasteners with additional security cable and regular inspection.
- lamps consecutive working hours is not recommended more than 10 hours.
- should stop using the lights in time when happens unusual conditions during the process
- lamp parts of the rotation, external accessories and paste parts should be regular inspected, such as the emergence of loose and rock, should be reinforced in a timely manner to prevent the accident.
- lamps adopt strong winds to refrigerate, it is easy to accumulate the dust, so you have to clean it weekly especially the cooling air opening, otherwise the dust will plug leading to poor light
TECHNOLOGY REFERENCE
Power Supply: AC 100-240V/50-60Hz
Power consumption: 10W
Light source: 3pcs*3w LED RGB 3in1 mixing color
Beam Angle: 10/25 degree
Dimmer: 0-100% dimmer
Strobe rate:0-24HZ
Working Environment: -20℃-40℃
IP rate: IP20
DMX Channels: 7 channels
Control Mode: DMX512,Master-slave,Sound,Auto ,remote
Remote: IRC remote
Battery information:
Battery type: Lithium Ion
Battery Charge Time: 6hours(full power)
Battery Life: (all on) 8hours, (single Color) 24hours
Battery Power:12 V, 6Ah
IEC power In/Out(charging)
DMX control, 3pin In/Out
Indicator light:
Charging: Red
Charging full: Green
Using/Turn off: still on Green (control by battery)
Board Instruction
Operate Menu
| No. | Display | Function |
|---|---|---|
| 1 | D001 | Address（01-512） |
| 2 | CC01-CC64 | Color selection, select different color by up anddown |
| 3 | RB01-RB16 | Color gradual change, from slow to fast by upand down |
| 4 | PL01-PL16 | Color Pulse change, from slow to fast by up anddown |
| 5 | SD01-SD16 | Color Jump change, from slow to fast by up anddown |
| 6 | FL01-FL16 | Flash, from slow to fast by up and down |
| 7 | Sound | Sound effect |
| 8 | R000-R255 | Red color, dimmer from dark to bright |
| 9 | G000-G255 | Green color, dimmer from dark to bright |
| 10 | B000-B255 | Blue color, dimmer from dark to bright |
DMX CHANNEL SHEET
7CH mode
| CH | Value | Function |
|---|---|---|
| 1 | 0-255 | Master dimmer from darkness to brightness |
| 2 | 0-255 | Red from darkness to brightness |
| 3 | 0-255 | Green from darkness to brightness |
| 4 | 0-255 | Blue from darkness to brightness |
| 5 | 0-255 | Strobe from slow to fast |
| **** 6 | **** 0-255 | 0—10：No function11－60：Color |
selection(color controlled by CH7)61-110: Color gradual change, speed
controlled by CH7 111-160：Color Pulse change, speed controlled by CH7
161-210：Color Jump change, speed controlled by CH7 211—255：Sound
7| 0-255| Color selection of CH6(11-60 value)Speed control of CH6(61-210
value)
FIXED EQUIPMENT
Please fasten the fixture clamp before hanging. The clamp can be fasten by the little hole in the middle of the bracket, then tie with a safety belt. The loading capacity of the safety belt should be 10 times than the weight of the fixture itself.
CONNECTION OF DMX-512 AND CONNETION WITH THE LIGHT EQUIPMENT
Please connect XLR-XLR control wire with every light from the output of
DMX. XLR connection:
ATTENTION: Please do remember to connect one circle circuit plug on the
output signal of last equipment. And this circle circuit plug was connected a
120ohm resistance between terminals 2 and 3 of the
CANON plug, connect this circle circuit plug can avoid the signal flash
phenomena of signal DMX512 during the transmission.
Maintenance
| Problems | Check list | Trouble Shooting |
|---|---|---|
| The fixture do not work |
- If your power as same as the input of the machine.
- If the fuse was broken.
| 1. Make sure the voltage.2. Replace the same fuse.
LED dimmed| If your power us same as the input of the machine| Make sure the
voltage input.
No DMX input|
- If the polarity is opposite in the DMX controller.
- If it is in DMX mode.
| 1. Correct the DMX polarity.2. Change to the DMX
| If there are 2 Master in a loop.| mode.3. Set one piece into Slave mode.
Par Light Set works abnormality| 1. Check if the serial is correct on the Par
Light display| 1. Set the right serial No on the single Par Light
AFTER SERVICE
- Our company offer technical consultation to customers for ever.
- If the machine is wrong and need repairmen, please truthfully fill in the related content and feedback us the problems timely, as well as we have to improve the product.
- In addition to the lamp, also matching accessories are as follows:
accessories: Power line 1 piece Optional parts: (customers)
Warranty Card
Description: These must be truthfully fill, seal by the end-user and point-of-sale, or else the warranty will not work (warranty period and terms, see the following) warranty period：one year since purchase warranty terms：1、If fail when using the product in normal state, you can made under the provisions of the warranty, show the warranty card and purchase bills(copy), and enjoy free maintenance service in a specific service center or the manufacturer.
The following will be the implementation of paid service:
- Without the effective warranty card
- There’s blank, alter and no point-of-sale name
- Fail caused by unresistance
- Fail caused by transportation or unloading
- Fail caused by not operate by manual
- Fail caused by disassemble without unauthorized
- Fail caused by using the unauthorized control system
Note:
Based on our company continue to improve the product, the statement
containing data may have changed, and will not notice the change any more.
Company retains its right to change specifications related when product is
improved. Thanks for your understanding.
