azponds 550GPH-77379 Oase Aquarius Fountain Set Eco 550 Pump Installation Guide
- June 12, 2024
 - azponds
 
Table of Contents
- azponds 550GPH-77379 Oase Aquarius Fountain Set Eco 550 Pump
 - Intended use
 - Installation and connection
 - Installing the pump
 - Adjusting the water feature
 - Maintenance and cleaning
 - Cleaning/replacing the impeller unit
 - Storage/winter protection
 - Malfunction remedy
 - Read User Manual Online (PDF format)
 - Download This Manual (PDF format)
 
azponds 550GPH-77379 Oase Aquarius Fountain Set Eco 550 Pump

Intended use
Only use the product described in this manual as follows:
- For pumping normal pond water for filter systems, waterfall systems and water course systems.
 - For household use only.
 - Operate in accordance with instructions. (→Technical data)
 
The following restrictions apply to the unit:
- Do not use in swimming ponds.
 - Never use the unit with fluids other than water.
 - Never run the unit without water.
 - Do not use for commercial or industrial purposes.
 - Do not use in conjunction with chemicals, foodstuff, easily flammable or explosive substances.
 
Installation and connection
Installing the water feature
- In addition to the water feature, you can connect a rivulet or waterspout to the stepped hose adapter (hose diameter ½, ¾ or 1 in). 

 
Installing the pump
WARNING
- Severe injuries or death due to operation of this unit in a swimming pond. Defective electrical components will electrify the water with dangerous electrical voltage.
 - Never operate the unit in a swimming pond.
 - The unit is subject to dangerous voltage and must not be installed directly adjacent to the water. Otherwise there is a risk of severe injuries or death by electrocution.
 - Install the unit at a distance of at least 2 m from the water to ensure that it is pro-tected against flooding.
 - Ensure that the connection to the power supply is at least 6.6 ft from the pond.
 - Place the pump horizontally on a stable, mud-free surface.
 - The pump is under water, the nozzle intake emerges from the water.
 - TIP! Thoroughly clean the pond or pool and place the pump approx. 200 mm above the bottom of the pond, so that no muddy water runs through the pump.
 - Muddy water will cause the nozzle to clog faster and the impeller unit to become worn prematurely.
 
Adjusting the water feature
Commissioning/start-up
WARNING
- To reduce the risk of electric shock, be certain that the unit is connected only to a properly grounded, groundingtype receptacle.
 
NOTE
- Never connect the pump to a dimmer. Otherwise the pump will be destroyed.
 - Switching on: Plug the power plug into the outlet.
 - The unit switches on immediately.
 - Switching off: Pull the power plug from the outlet.
 
Maintenance and cleaning
NOTE
- Never use chemical cleaning agents. These are hazardous to animals, plants and the environment.
 - Only use clear water and a soft brush to clean the unit.
 
Recommendation regarding cleaning:
- Clean the unit as required, but at least twice a year.
 - When cleaning the pump, pay particular attention to the impeller unit and the pump housing.
 
Opening/closing the housing
- Before closing the housing, place the power cable in the recess in the housing to pre-vent it from being crushed.
 
Opening the housing
Closing the housing
Cleaning/replacing the impeller unit
- Remove the pump cover or pump housing from the motor housing by turning it counter-clockwise (bayonet catch).
 - After removing the impeller unit, clean all parts under running tap water.
 - Replace a worn or damaged impeller unit.
 - Assemble in the reverse order.

 
Storage/winter protection
- The unit is not frost-proof and has to be removed and put into storage if minus tem-peratures are expected.
 
How to correctly store the unit:
- Thoroughly clean the unit, check it for damage and replace any damaged parts.
 - Store the pump submerged and in a frost-free environment.
 
Malfunction remedy
| Malfunction | Possible cause | Remedy | 
|---|---|---|
| Pump does not run | No mains voltage | Check the mains voltage. | 
| Impeller unit blocked | Clean the impeller unit | |
| Insufficient delivery rate | Impeller unit running slug- gishly | Clean the | 
impeller unit
 | Filter housing clogged| Clean the filter housing.
 | Pressure loss in the hose too high|
- Reduce the hose length and connecting pieces to a mini- mum
 - Route hose in a straight line
 
Unit switches off after a short running period| Water temperature too high|
Adhere to the maximum water temperature of +77 °F (+35 °C)
 | Unit is overloaded|
- Remove blockage
 - The unit will switch on again automatically as soon as it has cooled down.
 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>