ifi Go pod Wearable HD Bluetooth Headphone User Guide
- June 12, 2024
- ifi
Table of Contents
ifi Go pod Wearable HD Bluetooth Headphone
Product Information
The GO pod is a wearable HD Bluetooth DAC/headphone amp that comes with a
charging case. It has a built-in mic for hands-free calls when paired with
your smartphone. The charging case has LED
indicators to show the battery status of the GO pod. It also supports USB-C
battery charge input and Qi wireless charging battery charging input. The GO
pod is capable of storing up to 8 paired Bluetooth devices.
Product Usage Instructions
Thank you for purchasing this GO series pod. The GO pod is an Wearable HD Bluetooth DAC/headphone amp.
GO Pod Status Indicator: The LED on the GO pod indicates its status as follows:
- Charging: Steady Red
- Fully charged: Light off
- Awaiting connection: Flashing Blue
- Ready to pair: Alternately flash Red and Blue
- Successfully paired: Light off
- Factory Reset: Steady Blue 3s. Alternately flash Red and Green (only operated within Gaia APP when in binaural working mode)
LED Status
Charging: Steady Red
Fully charged: Light off
Awaiting connection: Flashing Blue
Ready to pair: Alternately flash Red and Blue
Successfully paired: Light off
Factory Reset: Steady Blue 3s. Alternately flash Red and Green (only operated
within Gaia APP when in binaural working mode)
To enter the pairing mode manually, press the left and right touch area
together for 2 seconds until the LED flashes red/blue. The GO pod can store up
to 8 paired Bluetooth devices.
Touch control area
- Play/Pause/Answer the call (Single tap)
- Reject/hang up (Double tap)
- Skip forward (Double tap)
- Skip back (Triple tap)
- Volume Up (Hold right, used when in binaural working mode, not available in monaural working mode))
- Volume Down (Hold left, used when in binaural working mode, not available in monaural working mode))
- Wake up voice assistant (Single tap then hold)
- Bluetooth Pairing (Hold left and right together for ≥ 2s)
- Power Reset (Hold left or right for ≥12s, release when steady blue light is on*)
Tip: The reboot function can be used when the GO pod is abnormal or
dead.
Microphone:
The GO pod has a built-in mic for hands-free calls when paired with your
smartphone. To wake up your phone’s voice assistant, single tap then hold left
or right for 2 seconds on the touch control area.
Built-in mic for hands-free calls when paired with your smartphone.
Tip: To wake up your phone’s voice assistant, Single tap then hold left
or right for ≥2s the Touch control area (2). 5V/1A USB-C battery charge
input
For charging only. 5V/1A and above Type-C charger.
5V/1.5A Qi wireless charging
battery charging input
Use a 5V/1.5A and above Qi certified wireless charger.
Charging box LED for Battery
LED Status
4/4 > 75%
3/4 > 50%
2/4 > 25%
1/4 25%
- Battery LED will flash when it is charging and will go out when it is fully charged.
Charging: The GO pod supports USB-C battery charge input and Qi wireless charging battery charging input. The charging box LED indicates the battery status with different LED lights flashing when the battery is charging or fully charged.
Bluetooth Pairing
When removed from the charging case, the GO pod automatically searches for a
previously paired device. If a stored device is not found, it automatically
enters pairing mode with LED blinking blue and red. To connect to a Bluetooth
device, turn on the phone’s Bluetooth function and select GO pod in your
Bluetooth list.
When removed from the charging case, GO pod LED blinks blue as it
automatically searches for a previously paired device. If a stored device is
not found, it then automatically enters pairing mode with LED blinking blue
and red. To enter pairing mode manually, Press the left and right touch area
together for ≥ 2s until LED flashes red / blue. The GO pod is able to store up
to 8 paired Bluetooth devices. Manual reconnection may still be necessary.
Connecting to Bluetooth device
Turn on the phone’s Bluetooth function, and select ” GO pod” in your Bluetooth
list.
GO pod Auto-connecting
The GO pod switch on and connect to each other automatically when taken out of
the charging case. And the GO pod will flash blue lights to indicate that the
GO pod are automatically interconnection to each other. Once interconnection
successfully, the GO pod L +R will alternately flash the red light and blue
light.
Single-GO pod Mode
Removing the right or left GO pod from the charging case, it will
automatically turn on, and select “GO pod” (Left GO pod) or “GO pod” (Right GO
pod) in the Bluetooth list to connect GO pod. If the GO pod has not
successfully connected to Bluetooth for more than 5 minutes, they will
automatically shut down.
When the GO pod is placed back in the charging case it automatically switches
off and goes into charging, the binaural hanging steady red light is always on
until it is fully charged and then goes out. Do not leave the left and right
GO pod too far when you take out them from the charging case for pairing. The
recommended distance is no more than 15 CM.
Set up your Bluetooth connection
using our iFi-Gaia APP
Please search for “GO pod” within the Gaia app. The Gaia app helps you to use
all functions and settings of the headset, such as digital filters to adjust
the sound, Resetting of GO pod.
Ear loops connected to the GO pod touch control
units Three ear loop pairs are supplied: 0.78mm 2-pin, MMCX. Scan the QR code
to view the official iFi audio GO pod video on YouTube.
Cautions
- Avoid extreme heat, cold and humidity.
- Avoid dropping or crushing the GO pod, stressing ear loop by rapid pulling or extreme force, or bending ear loop at sharp angle
- If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
- If you experience regular discomfort while using this product, discontinue use and consult the physician.
Warning: Dry the GO pod completely before placing them in the charging case to avoid damaging the case.
iFi-Gaia: The Gaia app helps you to use all functions and settings of the headset, such as digital filters to adjust the sound, resetting of GO pod. To set up your Bluetooth connection using our iFi-Gaia APP, please search for GO pod within the Gaia app.
Ear Loops: Three ear loop pairs are supplied: 0.78mm 2-pin, MMCX. Ear loops are connected to the GO pod touch control units.
Specifications
-
Bluetooth version ： Bluetooth 5.2TM
-
Codecs： LDAC, LHDC/HWA, aptX Adaptive, aptX, AAC, SBC
-
Chipset: Qualcomm QCC 5100 Series
-
Chipset: 10 m
-
Auto impedance detection: 16Ω/32Ω/64Ω/300Ω
-
SNR: 32Ω ≥129dB (A) / 300Ω ≥132dB (A)
-
THD + N: ≤0.002% (1kHz/32Ω)
-
Frequency response: 10-20kHz(-3dB) LDAC
-
Battery: Ear hood 180mAh + Charging box 1500mAh
-
Working hours: Ear hood ~7h + Charging box ~30h
-
Charging time: Ear hood ~1.5h + Charging box ~2h
-
Power System: 5V/1A or 5V/2A Qi certied charger
-
Dimensions:
Ear hood 43.5 x 16.4 x 9.5 mm (1.7″ x 0.6″ x 0.4″)
Charging box 116 x 76 x 38.5 mm (4.6″ x 3″ x 1.5″) -
Net weight:
Ear hood 12g (0.42 oz)
Charging box 126g (4.44 oz) -
Limited Warranty: 12 months**
-
LDAC – 660k(stereo) 990k(mono), LHDC – 560(Stereo) 900k(mono)
-
12 months typical or as permitted/required by local reseller laws.
-
Specifications are subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>