Jushua 700190 Industrial Wall Vanity Light with Shade Instruction Manual

Jushua 700190 Industrial Wall Vanity Light with Shade

Product Information

The model number of the product is 700190. The product requires a supply circuit of 120V, 60Hz, and a bulb type of 1E2660W Max. The compatible bulb type for the product is 8W LED ST58 or A19 bulb. The package includes a fixture with hardware, a lampshade, and a parts bag. The parts bag includes parts X 2 for 2 pack item.

Product Usage Instructions

1. Open the box from the top and take out all the components, parts bag, and manual carefully.
2. Check all the components against the parts list and make sure that each part on the list is present.
3. If any parts are missing or the glass is damaged, contact the manufacturer at support@micsiu.com to get a replacement. Parts that are shown as 0 under QTY are not included.
4. Follow the assembly and wiring illustration provided in the manual using the parts included in the package.
5. Install the compatible bulb type (8W LED ST58 or A19 bulb), which is not included in the package, into the product.
6. Connect the product to the required supply circuit of 120V, 60Hz.

IMPORTANT SAFETY INSTRUCTIONS

• Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
• Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov.
• Caution: Electrician installation is highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read the instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.

Important Notice

• This is a generic instruction sheet used for various fixtures.
• The finish, shape, and style of the fixture/glass/shade/diffuser may vary.

(Required Supply Circuit: 120V, 60Hz. Bulb Type: 1E2660W Max)

Compatible Bulb Type: (NOT Included)The mostly suggested bulb type is 8W LED ST58 or A19 bulb

COMPONENTS INCLUDED IN THE PACKAGE

• Fixture with hardwares
• Lamp shade
• Parts included in parts bag Parts X 2 for 2 pack item

ASSEMBLY & INSTALLATION STEPS

1. Open the box from the top, and take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each part on list. If any parts missing and the glass damaged, please contact the manufacturer at: support@micsiu.com to get a replacement. Parts are NOT included for which is shown as 0 under QTY.

PARTS LIST                    (Parts QTY X 2 for 2 pack item)

Part Name| QTY| Code|  | Part Name| QTY| Code
Junction Box| 0| A| Wire Nut| 3| I
Leading Wire| 0| B| Wire| 2| J
Mounting Screw| 2| C| Socket| 1| K
Cross Bar Mounting Bracket| 1| D| Lamp Shade| 1| L
Stud| 2| E| Light Bulb| 0| M
Back Plate| 1| F| Socket Ring| 1| N
Washer| 2| G| Tool| 1| O
Cap Nut| 2| H|  |  |

1. Refer to the illustration while doing assembly and follow the steps as below:
   • I Assemble the lamp shade (L) to the socket (K) , fix the socket ring (N) by the tool (O). Screw on the bulb (M) to the socket or do this step after installation.
   • II Thread two studs (E) onto the mounting bracket (D) at the proper position.
   • III Attach the mounting bracket (D) to the junction box (A) by two mounting screws (C). Adjust the mounting bracket to make the fixture installed at a horizontal level.
   • IV Connect wires according to the wiring diagram as below.
   • V Attach the backplate (F) to two studs (E) and fix with two washers (G) and cap nuts (H)

Illustration of assembly and wiring

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>