stretta 160400 4 ft. White Laminate Countertop Kit Instructions
- October 30, 2023
- stretta
Table of Contents
stretta 160400 4 ft. White Laminate Countertop Kit
Product Information
Stretta Backsplash Instructions
With Stretta’s patented installation process, installing a countertop has
never been faster or easier!
Contains:
- One Backsplash
Tools Required:
- Cotton Construction Cloth
- Drill
- Adhesive
- Wood Bits
- Screws
- Safety Glasses
Product Usage Information
Step 1 – Prepare the Surfaces
To achieve a perfect bond, it is important to wipe down the backsplash and
surface of your Stretta countertop with a dry cotton cloth to remove any loose
particles or debris. (Figure 1-1)
Step 2 – Setting the Backsplash
Apply construction adhesive to the back and bottom surfaces of the
backsplash. (Figure 2-1) Set the backsplash in place and apply pressure so
that the excess construction adhesive is squeezed out. (Figure 2-2) Clean up
the excess construction adhesive immediately with warm water and a cotton
cloth.
Step 3 – Securing the Backsplash (Optional)
Due to variances in wall straightness, you may need to take additional
measures to secure your Stretta backsplash. To further secure your backsplash
to the countertop, first drill pilot holes every 12 inches through the
underside of the countertop and into the backsplash to prevent splitting.
(Figure 3-1) Then, using wood screws; screw into the pilot holes while holding
the backsplash in place. (Figure 3-2)
Stretta Endcap Instructions
With Stretta’s patent-pending installation process, installing a countertop
has never been faster or easier!
Endcap Kit Contains: Two Endcaps
- Endcap Front (Laminate)
- 3M Adhesive Backing
Tools Required:
- Measuring Utility Tape
- Scissors
- Cotton Cloth
- Masking Fine Wood Tape
- File
- Safety Glasses
Step 1 – Test Fit
Remove endcaps from the packaging and test fit them to the exposed ends of
the countertop to make sure they cover the ends. (Figure 1-1) If you need to
finish the ends of the backsplash, cut 4 off each endcap with the utility
scissors and set the 4 pieces aside. (Figure 1-2) With a dry cotton cloth,
wipe the exposed ends of the countertop to remove any loose particles or
debris.
With Stretta’s patented installation process, installing a countertop has never been faster or easier!
IMPORTANT INFORMATION ABOUT YOUR STRETTA COUNTERTOP
- CAUTION: The product is heavy and should be lifted by two people to avoid injury or damage during installation.
- For Indoor Installation Only
- To clean your Stretta countertop, use a mild dish soap and warm water applied with a soft cloth. Do not utilize abrasive cleaners or cleaning tools. Always test cleaning products in an inconspicuous area first.
- Your Stretta countertop is manufactured with 100% pre-consumer recycled cores and low- emitting, water-based adhesives.
One Backsplash
TOOLS REQUIRED
Installation
STEP 1 – PREPARE THE SURFACES
To achieve a perfect bond, it is important to wipe down the backsplash and
surface of your Stretta countertop with a dry cotton cloth to remove any loose
particles or debris. (Figure 1-1)
STEP 2 – SETTING THE BACKSPLASH
- Apply construction adhesive to the back and bottom surfaces of the backsplash. (Figure 2-1)
- Set the backsplash in place and apply pressure so that the excess construction adhesive is squeezed out. (Figure 2-2) Clean up the excess construction adhesive immediately with warm water and a cotton cloth.
STEP 3 – SECURING THE BACKSPLASH (OPTION)
- Due to variances in wall straightness, you may need to take additional measures to secure your Stretta backsplash. To further secure your backsplash to the countertop, first drill pilot holes every 12 inches through the underside of the countertop and into the backsplash to prevent splitting. (Figure 3-1)
- Then, using wood screws; screw into the pilot holes while holding the backsplash in place. (Figure 3-2)
CAUTION: Take care when pre-drilling the pilot holes and screws so that the bit or screw enters straight into the surfaces and not at an angle, otherwise you risk surface penetration.
ENDCAP KIT CONTAINS
ENDCAP KIT CONTAINS: TWO ENDCAPS
TOOLS REQUIRED
Installation
STEP 1 – TEST FIT
Remove endcaps from the packaging and test fit them to the exposed ends of
the countertop to make sure they cover the ends. (Figure 1-1) If you need to
finish the ends of the backsplash, cut 4” off each endcap with the utility
scissors and set the 4” pieces aside. (Figure 1-2) With a dry cotton cloth,
wipe the exposed ends of the countertop to remove any loose particles or
debris.
STEP 2 – APPLY ENDCAPS
Remove the paper backing on the endcap to expose the adhesive. Line the
endcap up with the end of the countertop so that it is flush with the front
edge and top of the countertop surface. (Figure 2-1) With your hand, press the
endcap firmly against the end of the countertop to activate the adhesive.
CAUTION: Take care to properly position the endcap, as it is difficult to reposition the endcaps after the adhesive has set.
STEP 3 – FINISH ENDCAPS
Once the endcap is applied, using utility scissors, trim off as much of the
excel material as possible. (Figure 3-1) Then facing the endcap, use a fine
file and safety glasses, and place the file nearly parallel to the counter.
File in a single-direction movement towards the countertop, always from front
to back, (Figure 3-2) until there is no excess material and the endcap is
flush with the end of the countertop.
CAUTION:
Take care while filing so you do not file the surface of the countertop, as it
can damage the finish. Masking tape can be placed on the countertop surface to
protect while filing, if necessary. (Figure 3-3).
STEP 4 – FINISH BACKSPLASH
If needed, to finish the end(s) of your backsplash, locate the 4” pieces of
endcap material. (Figure 4-1) First, use a dry cotton cloth to wipe the
exposed end(s) of the backsplash to remove any loose particles or debris. Then
follow steps 2 and 3 above to finish the exposed ends of the backsplash.
For additional information on installing your Stretta countertop, please visit strettacountertops.com.
©2020 VT Industries, Inc. All rights reserved.
All trademarks and registered trademarks are the property of their respective
owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>