HINOMI Intelligent Electric Lifting Table Instruction Manual

 HINOMI Intelligent Electric Lifting Table

INTRODUCTION

Please read this manual carefully before installation and reading
Product name: Intelligent electric lifting table

Hardware fitting

Tool

Main material:

• 1.5mm thick steel
• pipe 20# steel
• 2.0mm thick steel plate
• 304 stainless steel bar
• 2.0 mm thick steel pipe
• 2.0 mm thick steel plate
• ABS plastic,PCB board
• 25mm thick wood pellet
• board MFC veneer

Auxiliary materials:

• Metal screw bag
• PVC edge banding

Material parts:

• Table leg pipe fittings
• Lift screw
• Flanks
• Hexagon drive bar
• beam
• foot
• Controller ;hand control le
• table base material
• Desks facing

Material parts:

• installation
• Table edge sealing strip

SPECIFICATION

• Product Model: MSC32T1
• Execution standard: QB/T 5271-2018
• Input voltage: DC 22-32V, 6A
• Working mode: electric lifting
• Work schedule: Max. 10% work 2 minutes and 18 minutes rest (When the open landing table continues to rise or descend for 2 minutes, there will be a warning of overheating protection, and the LED screen will display” H01 “. The operation button of the lifting table will not be able to operate, and it will be restored to normal after 18 minutes.
• Rated load: SOON (~80kg)
• lifting speed: 22mm/s
• Lifting stroke: 480mm
• Minimum desktop height: 720mm
• Maximum desktop height: 1200mm

Precautions for use

1. clean regularly, every week is advisable.
2. do not use a lot of water, corrosive liquids, chemicals when wiping.
3. The product must use a power supply that meets its electrical performance requirements.
4. Do not replace the connecting cable with other specifications.
5. This product should not work in the environment of humidity or extremely low and extremely high temperature for a long time, humidity and high temperature will lead to the failure of electronic components, low temperature will lead to the condensation of internal lubrication grease.
6. This product can only be used at home or office. Do not use it in other inappropriate situations.
7. Do not place objects that exceed the maximum load on the product.
8. lf the fault occurs, please refer to this manual operation, if the fault cannot be solved, please contact after-sales personnel in time to deal with, do not dismantle the relevant parts without permission, to avoid electric shock, mechanical damage and other risks.

Installation Notes

1. Step 1: Place table feet@ on the table board G)
2. Step 2: Install sides screws for both feet by tool M4
3. Step 3: Lock the beam with screws
4. Step 4: Install screws on both feet
5. Step 5: Fix voice-operated control by screws
6. Step 6: Connect motor wire and controller wire
7. Step 7: Insert power cord
8. Step 8 Rearrange the power cord with ST4*16&ATC-l 7, Assembly

Operation Instruction

The whole manual controller is operated by pressing buttons. When there is no operation for 10 seconds, the display screen will go to sleep. You can wake up the screen by pressing random buttons and continue to use the screen when it lights up.

• LED current height display

  • Displays table height values.

• Adjust up & down

  • Adjust the height of the table by pressing the up/down buttons until it fits your best position.

• Preset height (1/2/3/4)

  • After setting the memory key, it will automatically rise and fall to the height of memory.
  • Set memory height
  • Touch the ‘M’ key: the display shows ‘S-‘.Touch one of the number keys,the current height will be stored to that key.

• Setting (M)

  • To set the memory location and internal parameters, press ‘M’.

• Resetting the base

  • Condition
  • Error E07-E09 (Even if it is restarted, it is still an error dispiay and pressing any key doesn’t work.)
  • Operation
  • After pressing the down for 5 seconds, the display shows RST. Release the button the down button again to reset.

• Safety function

  • In the process of rising or falling, the table will automatically rebound when encountering reverse resistance.

• Set the upper limit

  • Touch the ‘M’ key: the display shows ‘S-‘.Touch the ‘UP’ key: the display flashes. Touch and hold the ‘M’ key for 2s until the display shows ‘999’. The upper limit is  now stored.

• Set the lower limit

  • Touch the ‘M’ key: the display shows ‘S-‘. Touch the ‘DOWN’ key: the display flashes. Touch and hold the ‘M’ key for 2s until the display shows ‘000’. The lower limit is now stored.

• Delete height limits

  • Touch the ‘M’ key: the display shows ‘S-‘. Touch and hold the ‘M’ key for 2s until the display shows ‘555’. Both upper and lower limits are deleted.

• Locking

  • Press M button, the screen shows “s-“, keep it for 5 seconds, The screen returns the number, continue to hold the M button for 3 seconds; The screen shows LOC to complete the lock.

• Unlocking

  • In the LOC situation, press the button for 8 seconds; When the screen displays the number, it is unlocked.

• Change the RESET height

  • Under the reset situation, it shows RST, press M button for 5 seconds, screen shows height and flashes; Then press up or down button to adjust the height to what you need; Release the button for 5 second shows RST, successfully adjust.

• Memory point continuous switching

  • Under the Reset situation, it shows RST; Press key 1 for 5 seconds, switch memory point and memory continuous change:
  • Screen shows “10.1” memory point continuous change.
  • Screen shows “10.2” memory point change.

• Changing between inches and centimeters

  • Press and hold the “2” Button for about 5 seconds to switch the setting. The display will automatically return to a flashing “RST” . Press the DOWN button until the desk lower a little more and slightly risen.
  • The new setting is displayed. Repeat the process to switch back. “10.3” is centimeters, “10.4” is inches.

• Changing the anti-collision sensitivity

  • Follow the Reset instructions until the LED flashes “RST”. Press and hold the UP button for about 5 seconds while the LED flashes “RST”and then switches to either:
  • 10.5 = 10kg pressure (most sensitive) e)
  • 10.10. 6 7 = = 20kg 15kg pressure pressure (least (middle sensitive) sensitiv

• Normal problems and solutions

  1.  If your desk has the problems as below, please try to reset it
  • Abnormal work
  • Handset shows “RST’
  • Handset shows error code but all the cables connected normal.
  2. If handset shows “HOT”, please cut off the electrical source for about 20 minutes.

• Troubleshooting and inspection
  Connect the connecting cables to control box/lifting column /power supply Remarks:

  1. M1 and M2 are the interface of N2 control box which connect the lifting columns.
  2. M3 is the interface in the JC35TT product {three-column N3 control box) which connect the third lifting column.
  3. E07 indicate the M1 line Hall error. If the error code still exists after resetting, then need troubleshooting.
  4. EOB indicate the M2 line Hall error. If the error code still exists after resetting, then need troubleshooting.
  5. E09 indicate the M3 line Hall error. If the error code still exists after resetting, then need troubleshooting.

“Please co markmments “-/” in or the “x” in bottom the after comments you list perform if you this have step. any Or write inquiries. down the

Voice Control Operation Instruction

Wake word

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>