AVENO life Wooden Couch ALEXA User Manual

AVENO life Wooden Couch ALEXA

PARTS

ASSEMBLY

Product Information

Monta, Instrukcja Obsługi i Gwarancja Leżanki Drewnianej ALEXA
This user manual provides assembly instructions and warranty information for the wooden couch ALEXA. The product is designed to provide comfort and support to patients during various medical treatments and massages. The couch has a table top, shelf, mobile leg, headrest, arms front shelf, and a face hole filler. The maximum weight capacity of the couch is 270kg. The product dimensions are 61/123 cm and 70 cm. The manufacturer recommends protecting the product from moisture during storage.

Height Adjustment

The height of the couch can be adjusted as per the requirement by following the below steps:

1. Put the couch on a hard and even foundation.
2. Set the appropriate couch height as shown in the table entitled Height adjustment.
3. Install the headrest (5) and the remaining equipment (6, 7)
4. Lifting of the mobile part of the couch takes place by setting the required height by hand.
5. ATTENTION! The lifting of the mobile part of the couch is possible only when the headrest is mounted on the opposite side of the movable part.
6. Lowering of the mobile part of the couche takes place by its maximum lifting and then lowering it down and securing by means of hook and loop fastener.

Laying the Patient

The patient sits at the couch side onto the upholstered top and adopts a comfortable horizontal position. The above-mentioned activities are safeguarded by the massage therapist, who determines the correct position on the table for the patient.

Cleaning and Disinfection

The couch should be disinfected occasionally as per the requirement

APPLICATION

Wooden couches enable the physiotherapist correct, safe and effective conduct of rehabilitation treatment, physiotherapy, physical therapy, massage, aiming at treating or alleviating the course of illnesses and the results of injuries /impairments. Used at the medical and doctor’s offices, they allow patients to adopt the correct posture for conducting effective and safe treatment or examination. The construction of the wooden couches enables the physiotherapist easy and complete access to the patient from each side, thanks to which all various treatments produce desired results and ensure proper conditions for the conduct of a treatment/examination.

CONSTRUCTION

1. Table top
2. Shelf
3. Mobile leg
4. Knob
5. Headrest
6. Arms front shelf
7. Face hole filler

OPERATION

1. Put the couch on a hard and even foundation.
2. Set the appropriate couch height as shown in the table entitled ”Height adjustment”.
3. Install the headrest (5) and the remaining equipment (6, 7).
4. Lifting of the mobile part of the couch takes place by setting the required height by hand. ATTENTION! The lifting of the mobile part of the couch is possible only when the headrest is mounted on the opposite side of the movable part.
5. Lowering of the mobile part of the couche takes place by its maximum lifting and then lowering it down and securing by means of hook and loop fastener.

HEIGHT ADJUSTMENT

AYING THE PATIENT

The patient sits at the couch side onto the upholstered top and adopts a comfortable horizontal position. The above-mentioned activities are safeguarded by the massage therapist, who determines the correct position on the table for the patients, and after the finished treatment helps them get down safely from the table.

MAINTENANCE, CLEANING AND DISINFECTION

Surfaces made of wood or plywood should be cleaned by means of soft damp cloth wiping them until dry. No chemical agents should be used. Notice! Wood as a natural raw material may have differences in the tree ring layout, differences in the shades as well as natural inserts like: streaks, dots. It does not devaluate the product quality, but on the contrary, it emphasises its natural origin. Such properties do not constitute a basis for a complaint. Disinfect when necessary and sporadically.

EXPLOITATION REMARKS

1. The couch is intended for use inside the dry and closed rooms and for the treatment of one person only at a time.
2. It is unacceptable to shift the couch along with a patient on it.
3. Rapid sitting on the couch (jumping on) is forbidden.
4. Sitting, kneeling and basing on the headrest, shelves and armrests is forbidden.
5. The couch should be used and stored far away from the direct sources of fire and heat.
6. Correct use of the couch will guarantee its long and failure-free exploitation.
7. Damages that arose as a result of noncompliance of the above-mentioned instructions do not constitute a basis for a complaint.
8. The couch should be used in accordance with the instruction manual.
9. Every person using the couch should familiarise oneself with the terms of the warranty and to observe them.
10. Only after meeting the above recommendations there are no contraindications to use the product.
11. Each serious incident related to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established.

TECHNICAL DETAILS

Name/Alexa

• Segments length: 61/123 cm
• Width: 70 cm
• Height: 64,5 – 83,5 cm
• Length: 1 85 cm
• Weight with accessories: 31 kg
• Foam thickness: 6 cm
• Dynamic resistance: 270 kg
• Static resistance: 1100 kg
• Max load allowed: 270 kg

Dynamic resistance – measurement made with an evenly distributed dynamic load, simula ng the tensions that occur during a typical classical massage.Sta c resistance -measurement made with an evenly distributed, fixed sta c load.

WARRANTY

The warranty does not cover any mechanical damages to the product. The buyer loses warranty rights in case of unauthorized repairs, modifications, or failure to report a defect within 14 days of detection. The warranty is limited to the repair of the product.

1. For the purposes of the guarantee:

   • a) “Manufacturer” refers to HABYS Spółka z ograniczoną odpowiedzialnością (Limited Liability Company) with its registered seat in Jasło, ul. Produkcyjna 16, 38-200 Jasło, entered into the Register of Entrepreneurs kept by the District Court in Rzeszów, XII Commercial Division of the National Court Register, with the assigned KRS number: 0000513317, with the share capital in the amount of PLN 10.750.000 (ten million seven hundred fifty thousand zlotys), the capital has been fully paid up, NIP: 6852208438, REGON: 180186290.
   • b) “Buyer” refers to the final Buyer of the equipment, manufactured by the Manufacturer, including both the consumer and the entrepreneur.
   • c) “Distributor” refers to an entity that, under an agreement with the Manufacturer, sells the Equipment in a designated area.
   • d) “Authorized Service Centre” refers only to a service held by the Manufacturer or a service indicated by the Manufacturer and held by its Distributor,
   • e) “Equipment” refers to a movable item, manufactured by the Manufacturer, being the subject of the sales and to which the said warranty applies.

2. The manufacturer ensures good quality and efficient operation of the equipment for which the warranty card has been issued, for the period of: 2 years for constructional elements, 2 years for upholstered elements.

3. The guarantee repair does not include the activities provided for in the manual, which the Buyer is obliged to perform on his own (installation of the Equipment, maintenance of the Equipment, etc.).

4. Liability under the guarantee covers only defects resulting from causes inherent in the Equipment., In particular, the guarantee does not cover any damage resulting from improper or inconsistent use, storage, maintenance or transport of the Equipment, as well as colour differences between the parts exposed and not exposed to solar radiation, the influence of chemical or abrasive agents, atmospheric pollution or accidental punctures and abrasions, the presence of stains or rings from greasy or dying substances (fats, creams, lotions or oils), permanent staining with dyes such as inks, permanent markers or other non-permanent dyes used in the production of clothing (e.g. dyes used to make blue jeans).

5. The guarantee does not cover any mechanical damage to the Equipment.

6. The buyer loses the guarantee rights in the event of:

   • a) the Manufacturer states that the Equipment was repaired by entity other than the Authorized Service,
   • b) making any design modifications to the Equipment without the prior written consent of the Manufacturer,
   • c) using the Equipment contrary to its intended use,
   • d) using the Equipment after revealing any defect in it.

7. Regardless of the loss of the guarantee rights, described above, in point 6, the Manufacturer shall not be liable for any damage to property or caused to third parties, which may be caused by the use of the Equipment covered by the guarantee.

8. The guarantee does not exclude or limit the rights resulting from the warranty for defects. Exercising the rights under the guarantee does not affect the seller’s liabilityunder the warranty for defects. If the Buyer exercises the rights under the guarantee, the time limit for the exercise of the rights under the warranty for defects is suspended on the date the Manufacturer is notified of the defect. The period runs further from the date of the Manufacturer’s refusal to perform the obligations arising from the guarantee or the ineffective expiry of the time for their performance.

9. The scope of the guarantee coverage is limited to the territory of the country in which the Equipment was sold.

10. The Manufacturer shall perform its obligations under the guarantee (removal of defects or damage to the structure of the Equipment arising from reasons inherent in the Equipment, and disclosed during the guarantee period) free of charge within 14 days from the date of delivery of the Equipment to the Manufacturer or the Authorized Service Centre. If the repair of the Equipment cannot be performed within the above-mentioned period, the Manufacturer shall inform the Buyer of the above, and also indicate the reasons for the delay and the expected date of fulfilment of the recognized guarantee request.

11. The use of the guarantee rights requires the total (cumulative) fulfilment of four conditions:

12. a) presenting a VAT invoice, receipt or other proof of purchase of the equipment to the Manufacturer, photographic documentation of the defective Equipment, together with a brief description of the reasons for submitting a guarantee claim,

13. b) reporting the defect within 14 (fourteen) days of its detection,

14. c) delivering the Equipment in original packaging at the expense of the Manufacturer, to the address indicated above in the guarantee card or to the address of the Authorized Service Centre,

15. d) designation of the place where the Manufacturer delivers the equipment after repairing it (limited to
    the country in which the Equipment was purchased).

16. The guarantee period is extended for the duration of the repair, starting from the date of delivery of the Equipment to the Manufacturer or to the Authorized Service Centre, to the date on which the Equipment was returned to the Buyer.

17. The responsibility of the Manufacturer or the Authorized Service Centre is to define the scope and the method of repairing the Equipment.The guarantee is limited to the repair of the Equipment. The Manufacturer reserves the right to replace the Equipment with a non-defective one, if the repair exceeds the price of the Equipment indicated in the proof of purchase. Under the guarantee, the Buyer shall not be entitled to demand that the Equipment be replaced with a new one. The guarantee, in particular, does not cover liability for losses or damages incurred by the Buyer in connection with the fact that one is not able to use the Equipment.

18. The Manufacturer shall not be liable for any damage to the Equipment caused during the performance of the transport service by the delivery company until it is collected by the Manufacturer from the delivery company.

19. If the shipment of the Equipment was ordered by the Manufacturer, the Buyer is obliged to check the technical condition of the Equipment upon its receipt. If the Buyer finds that the Equipment has been damaged during the transport, the Buyer is obliged to:

    • a) immediately, not later than within 3 days from the date of receipt of the shipment, notify theManufacturer of any damage to the Equipment that occurred during transport, in order to enable theManufacturer to submit a complaint to the delivery company and pursue related claims,
    • b) provide the Producer with a complaint report drawn up between the Buyer and the delivery company.

20. The guarantee regulations contained in this document are the sole and exclusive guarantee rules for HABYS limited liability products.

MEANING OF PICTOGRAPHS

Inne wersje językowe dostępne pod adresem: Other language versions available here:

www.habys.com/warrantymanuals

Manufacturer
ANJI BAISHENGJU FURNITURE CO., LTD
Green Home Furnishing Industrial Park,
Anji County, Huzhou City, Zhejiang Province, China Made in China

Authorized Representative
HABYS Sp. z o.o.
ul. Produkcyjna 16, 38-200 Jasło tel.: +48 887 766 115, info@habys.pl www.habys.l

References

• Stoły do masażu, stoły rehabilitacyjne, łóżka do masażu i rehabilitacji - Habys

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>