JANSKA Wall-Mount Range Hood User Manual

: June 10, 2024
: JANSKA

JANSKA Wall-Mount Range Hood

JANSKA-Wall-Mount-Range-Hood-product

Sweden Wall-Mount Range Hood

Models: RHW-3687 (36in) and RHW-4813 (48in)

User Manual

Your satisfaction is guaranteed. If you are not completely satisfied with our Wall-Mount Range Hood and the results it brings, we insist that you let us know. We’ll help make the Range Hood work for you, or we’ll refund your money.

Safety Definitions

WARNING: This indicates that death or serious injuries may occur as a result of non-observance of this warning.
CAUTION: This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.
NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note: This alerts you to important information and/or tips.

Important Safety Instructions

Please read and follow all instructions before using the range hood to prevent any hazards or injuries.

Installation Requirements

The following parts are supplied with the range hood:

Range Hood (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Exhaust Duct Cover (Upper and Lower) (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Exhaust Duct Base (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Exhaust Duct Base Gasket (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Duct Cover Mounting Bracket (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Wall Mounting Bracket (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
Mounting Bracket Screws for Hood (Flat head M5x12) (RHW-3687 (36in) x 6, RHW-4813 (48in) x 6)
Wall Anchor (RHW-3687 (36in) x 4, RHW-4813 (48in) x 4)
Wall Anchor Screw (RHW-3687 (36in) x 4, RHW-4813 (48in) x 4)
Exhaust Duct Cover Screws 4Mx6 (RHW-3687 (36in) x 4, RHW-4813 (48in) x 4)
K Exhaust Duct Base Screws (Cross-recessed mushroom screw 4×20) (RHW-3687 (36in) x 6, RHW-4813 (48in) x 6)
L Grease Tray (RHW-3687 (36in) x 1, RHW-4813 (48in) x 1)
M Stainless Steel Baffle Filter (RHW-3687 (36in) x 2, RHW-4813 (48in) x 3)
N Baffle Filter Handle and Screw (RHW-3687 (36in) x 4, RHW-4813 (48in) x 6)
O Duct Cover Hooks and Screws (RHW-4813 (48in) x 2)
P Baffle Filter Spacer (RHW-3687 (36in) x 2, RHW-4813 (48in) x 2)
Q Remote Control Hardware

Note: Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.

Parts Diagram

Prior to Installation

Location Requirements
This range hood has been designed to be wall-mounted, above the stove/hob. Before starting the installation, consideration should be given as to how the installation will be carried out, ensuring adequate space and clearance above the stove/hob.

Ventilation Requirements

Height and Clearance:

110 in. (2794 mm)
36 in. (914 mm)

To reach a 9 ft (2.74 m) ceiling, make sure the range hood is installed at least 30 in. (762 mm) from the cooking surface. 24 in. (610 mm) Min / 30 in. (762 mm) Max recommended

For the Most Efficient Operation

Electrical Requirements
Ensure there is the availability of an electrical power socket t power the range hood before fixing it to the wall. Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in accordance with the National Electrical Codes, ANSI/NFPA 70 (latest edition), all local codes, and ordinances.

Product Usage Instructions

Follow the below instructions to use the Sweden Wall-Mount Range Hood:

Before using the range hood, read and follow all instructions provided in the user manual to prevent any hazards or injuries.
Make sure that there is the availability of an electrical power socket to power the range hood before fixing it to the wall.
Ensure that the electrical installation is adequate and in accordance with the National Electrical Codes, ANSI/NFPA 70 (latest edition), all local codes, and ordinances.
This range hood has been designed to be wall-mounted above a stove/hob. Before starting the installation, consideration should be given as to how the installation will be carried out, ensuring adequate space and clearance above the stove/hob.
Consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.
Follow the ventilation requirements mentioned in the user manual for height and clearance.
Make sure that the range hood is installed at least 30 in. (762 mm) from the cooking surface to reach 9 ft (2.74 m) ceiling.
Use the supplied parts with the range hood for installation.

Your satisfaction is guaranteed. If you are not completely satisfied with our Wall-Mount Range Hood and the results it brings, we insist that you let us know. We’ll help make the Range Hood work for you, or we’ll refund your money.

SAFETY DEFINITIONS

WARNING
This indicates that death or serious injuries may occur as a result of non- observance of this warning.

CAUTION
This indicates that minor or moderate injuries may occur as a result of non- observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note: This alerts you to important information and/or tips.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING:

Use this unit only in the manner intended by the manufacturer.
Make sure that the voltage indicated on the rating plate of the appliance corresponds to your outlet voltage.
Do not attempt to alter the technical features of the range hood as this poses a safety risk.
Installation work and electrical wiring must be done by a qualified professional(s) in accordance with all applicable codes, standards, and fire-rated constructions.
DO NOT attempt to install this appliance yourself. The injury could result from installing the unit due to lack of appropriate electrical and technical background.
The range hood may have very sharp edges; please wear protective gloves if it is necessary to remove any parts for installation, cleaning or servicing.
The manufacturer does not accept any liability for any damage or injury caused by improper installation.
Due to the size of this range hood, a two-person installation is recommended.
WARNING: This range hood is for wall-mounting ONLY.
When cutting or drilling into walls or ceilings, be aware of electrical wires, piping, and other utilities.
To prevent backdraft, sufficient air is needed for proper combustion.
CAUTION: To reduce the risk of fire and to properly exhaust air, be sure to duct air out- outside.
DO NOT vent exhaust air into attics, crawl spaces, garages, or within walls and ceilings.
CAUTION: For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
This appliance is intended for normal family household use only. It is not approved for outdoor use. Use of this product in a commercial setting or if installed outdoors will void the warranty.
Do not operate the range hood with a damaged cord or plug.
Always have a working smoke detector near the kitchen.
Have an appropriate fire extinguisher available, that is nearby, highly visible, and easily accessible to the cooking appliance.
Apart from hazardous grease fires, small food fires should be extinguished by smothering with baking soda. Never use water on cooking fires.
Whenever possible, do not operate the ventilation system during a cooktop fire. However, do not reach through the fire to turn it off.
WARNING: TO REDUCE THE RISK OF A COOKTOP GREASE FIRE, READ THE FOLLOWING:
Use proper pan size. Always use cookware appropriate for the size of the surface element.
Never leave cooking elements unattended at high settings. Boil-overs can cause smoke and grease to spill over that may ignite. Heat oils slowly on low or medium settings.
Always turn the hood ON when cooking at high heat or when flambéing food.
Clean ventilation fans frequently. Grease should not be allowed to accumulate on the fan or filters.

WARNING: TO REDUCE THE RISK OF INJURY, IN THE EVENT OF A COOKTOP GREASE FIRE, READ THE FOLLOWING

SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES.
NEVER PICK UP A FLAMING PAN – you may be burned.
DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
Use an extinguisher ONLY if:
- You know you have a class A, B, and C extinguisher and you already know how to operate it.
- The fire is small and contained in the area where it started.
- The fire department is being called.
- You can fight the fire with your back to an exit.
In the event of a gas leak, DO NOT turn on the range hood or any type of ventilator. Open all doors and windows to disperse the gas.
Before servicing or cleaning the unit, switch the power off, and lock the electrical panel. This will prevent the power from accidentally turning on. If the electrical panel does not lock, secure a warning label, such as a tag, to the electrical panel.
The appliance is not intended to be used or cleaned by children or persons with reduced physical, sensory, or mental capabilities or a lack of experience and knowledge of the hazards involved.
WARNING: Repairs should only be done by a trained servicer. Improper repair of your appliance may result in a risk of severe physical injury or death.

PARTS SUPPLIED

JANSKA-Wall-Mount-Range-Hood-fig-1

Hardware Note: Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.

PARTS DIAGRAM

PRIOR TO INSTALLATION

Unpack the range hood and ensure all listed parts are in the box.
It is recommended for the vent system be installed before the hood is installed.
Before making cutouts, make sure there is proper clearance within the ceiling or walls for the exhaust vent.
It is recommended that a professional installer performs the range hood installation.

LOCATION REQUIREMENTS

This range hood has been designed to be wall-mounted, above a stove/hob. Before starting the installation, consideration should be given as to how the installation will be carried out, ensuring adequate space and clearance above the stove/hob. When installed, the range hood must be positioned at least 24in (61cm) and at most 30in (76cm) above the cooktop. NOTE: minimum of 30in (76cm) is required for a gas stove top. If the exhaust pipe is too long or there are too many bends, please select a suitable position to
install the range hood to ensure the appliance can suck in smoke efficiently. A straight or short duct run will allow the unit to perform most efficiently. Long duct runs, elbows, and transitions will reduce the performance of the unit.

Each elbow is equivalent to 5 to 10 feet (1.5 to 3.0 m) of straight run. Proper size ductwork should be 6 in. (15.2 cm) in diameter for RHW-3687 (36in) model and 8 in. (19.6 cm) for RHW-4813 (48in) model. If ductwork is already installed: ensure ductwork is free from debris and measures 6 in. (15.2 cm) in diameter for RHW-3687 (36in) model and 8 in. (20.3 cm) for RHW-4813 (48in) model. 1 in. (2.5 cm) reducers may be used but more than 1 in. (2.5 cm) will overwork the motor and the unit will not function properly.

VENTILATION REQUIREMENTS

This range hood must be ventilated to the outdoors.
Do not ventilate the range hood into an attic or other enclosed areas.
DO NOT use 4 in. (10.2 cm) laundry-type wall caps.
Use only metal/aluminum ductwork. A rigid metal/aluminum vent is recommended. Always keep the duct clean to ensure proper airflow.
DO NOT use a plastic vent.
Calculate the following figures before installation:
- Distance from the floor to the ceiling.
- Distance between the floor to the countertop/stove.
- Distance between the cooking surface to the range hood (recommend 24” to 30”).NOTE: minimum of 30” is required for gas stovetops.
- Height of hood and exhaust duct cover.

Height and Clearance

To reach a 9 ft (2.74 m) ceiling, make sure the range hood is installed at least 30 in. (762 mm) from the cooking surface.

FOR THE MOST EFFICIENT OPERATION

The minimum mount height between the cooktop to the hood bottom should be no less than 24’’ for electric cooktops or 30’’ for gas stove tops, and no higher than 30’’.
It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage or a fire hazard; while hoods mounted too high will be hard to reach and will lose its performance and efficiency.
It is recommended that the range hood be vented vertically through the roof through 6 in. (15.2 cm) in diameter for RHW-3687 (36in) model and 8 in. (20.3 cm) for RHW-4813 (48in) model, or bigger round metal/aluminum vent work.
The size of the vent should be uniform.
Use no more than three 90° elbows.
Make sure there is a minimum of 24” (61 cm) of straight vent between the elbows if more than one elbow is used.
DO NOT install two elbows together.
The length of the vent system and the number of elbows should be kept to a minimum to provide efficient performance.
The vent system must have a damper. If the roof or wall cap has a damper, DO NOT use a damper (if supplied) on top of the range hood.
Use HVAC foil tape or duct tape to seal all joints in the vent system.
Use caulking to seal the exterior wall or roof opening around the cap.
Due to different ceiling height configurations, recommended height may not be applicable.

ELECTRICAL REQUIREMENTS
Ensure there is the availability of an electrical power socket to power the range hood before fixing it to the wall. Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in accordance with the National Electrical Codes, ANSI/NFPA 70 (latest edition), all local codes, and ordinances.

– 110̃120V, 60 Hz., AC only, the fused electrical circuit is required.

INSTALLATION INSTRUCTIONS

PREPARE LOCATION

It is recommended for the vent system to be installed before the hood is installed.
Before making cutouts, make sure there is proper clearance within the ceiling or walls for the exhaust vent.
Disconnect the power.
A minimum of 6” (RHW-3687 model) and 8” (RHW-4813 model) round or 3-1/4 x 10” rectangular duct (both purchased separately) must be used to maintain maximum airflow efficiency.
Always use rigid-type metal/aluminum ducts if available to maximize airflow when connecting to the provided duct.
Please use Duct Run Calculation below to compute the total available duct run when using elbows, transitions, and caps.
ALWAYS, when possible, reduce the number of transitions and turns. If a reducer is used, install a long reducer instead of a pancake reducer. Reducing duct size will restrict airflow and decrease airflow, thus reducing duct size as far away from the opening as possible.
If turns or transitions are required, install as far away from the opening and as far apart, between two (2), as possible.
Place a thick, protective covering over the countertop, cooktop, or range to protect from damage or dirt.
Remove any hazardous objects around the area when installing.

Duct Run Calculation:

Recommended maximum run
6 in. or 3 1/4 x 10in. duct| 30 ft
Vent piece deduction
Each 90˚ elbow used| 9 ft
Each 45˚ elbow used| 5 ft
Each 6 in. to 3-1/4 x 10in. transition used| 7 ft
Side wall cap with damper| 0 ft
Duct Run Calculation:

IMPORTANT: This installation is for mounting the product to a wall. Ensure your wall has the proper support to hold the range hood weight (RHW-3687 36in – 44lbs / 20kg, and RHW-4813 48in – 52.8lbs / 24kg). These instructions are general guidelines; please consult your installation specialist regarding the best type of mounting hardware and support system based on your wall construction. All wall-mounted range hoods, if possible, should be installed and supported by studs behind the wall. In the event studs are not in alignment with the wall mount mounting plate holes, a wooden cross support system will need to be retrofitted to your existing studs. All homes are different, and installations will vary.
WARNING: Excessive Weight. At least 2 people are required to move and install this range hood. Spinal or other bodily injuries may occur if this warning is not observed.

VENTING METHODS

This range hood is factory set for venting through the roof or wall.
Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.

NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.

Place the range hood on a flat, stable surface. Connect the power cord of the range hood to a designated standard outlet, 120V/60Hz, AC only, and turn the range hood ON. Verify all operations of the range hood by referring to the Operating The Range Hood section of this manual, then turn the Range Hood OFF and unplug it from the power outlet.
Place all supplied parts and required hardware on a flat, stable surface and verify the existence of all supplied parts listed on Page 4.
Carefully remove the white plastic protective coat from the exhaust duct covers and baffle filters.
Remove the filters and filter spacers to reduce the weight for installation. Using the filter handles, lift each filter slightly upwards towards the motor, then angle the filter downwards until it can be removed from the hood frame.
Determine and mark the center line on the ceiling or wall where the range hood will be installed. Make sure there is proper clearance within the ceiling or wall for the exhaust vent.
CAUTION: If moving the cooking range is necessary to install the hood, ensure the power of an electric range is turned OFF at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
Using references in Height & Clearance on Page 6 use a pencil to mark the leveling point of the hood.
Fasten the Wall Mounting Bracket (Part F) to the back of the hood using Mounting Bracket Screws for the Hood (Part G).

INSTALL THE RANGE HOOD

Measure the distance between the stovetop and the bottom of the range hood. A distance between 24” to 30” is required. For gas stove tops, a minimum distance of 30’’ is required. Make sure the range hood is level and not tilted.
Mark the locations of the Wall Mounting Bracket holes on the wall. Make sure your mounting points are leveled when you mark them. It is recommended to install the hood directly into wood supports.
NOTE: Use threaded drywall anchors only when mounting the hood on sheetrock. Mounting the hood on wall studs or plumbers is highly recommended.
Place aside all equipment, locate marked regions, drill two holes in the marked region, then insert the two Wall Anchors (Part H) directly into the wall, gently tapping in place. Insert 2 Wall Anchor Screws (Part I) into the wall anchors. Leave the head of the screw approximately 1/8 in. away from the wall to allow for hanging.
Align and install the Duct Cover Mounting Bracket (Part E) close to the ceiling using 2 mounting screws appropriate for your wall construction. Make sure that the Duct Cover Mounting Bracket is in line with the Wall Mounting Bracket of the Range Hood below and that its height isn’t exceeding the maximum height of the Exhaust Duct Cover (31.5in / 80cm).
Align the Exhaust Duct Base Gasket (Part D) with the exhaust opening on top of the Range Hood, place the Exhaust Duct Base (Part C) on top of it, and fasten using Exhaust Duct Base Screws (Part K).
NOTE : Additional step for 48in models: Fix two Duct Cover Hooks with screws provided (Part O) to the top of the hood towards the wall side. You will use these two Hooks to fasten the Exhaust Duct Cover Top for additional stability.
Calculate the height of the duct and extend approximately 6” (15 cm) longer than required. Connect the duct to the Exhaust Duct Base on the Hood Body and seal the connection with HVAC foil tape or duct tape to make sure joints are secure and air-tight.
Raise the Hood Body and hang it onto the screws on the wall. Tighten screws to secure the hood to the wall.
CAUTION – Make certain the range hood is secure before releasing!
For safety purposes, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure the unit from the inside of the hood.
Connect the upper end of the duct to the vent system in the wall or ceiling.
Carefully slide the top half of the Exhaust Duct Cover into the Lower Exhaust Duct Cover (Parts B).
Fasten the Lower Exhaust Duct Cover to the Hood Body using Exhaust Duct Cover Screws (part J).
Carefully extend the Upper Exhaust Duct Cover until it reaches the Duct Cover Mounting Bracket.
Fix the Upper Exhaust Duct Cover to the Duct Cover Mounting Bracket using Exhaust Duct Cover Screws (Part J) on each side, left and right side of the Exhaust Duct Cover.
Once the hood is properly installed, insert the Grease Tray (Part L) into the stainless steel frame of the range hood, towards the rear. Push the Grease Tray down until firmly in position.
Install the Baffle Filter Spacers (Part P). Slide one filter spacer, flat side down, into the left frame of the range hood until firmly in position. Repeat on the right side.
Reinstall the Baffle Filters (Part M) into the Range Hood.
To install Baffle Filters:
- Install the baffle filters by inserting them at an angle toward the rear
- Push the filter up and insert the front of the filter into the front recess
- Slightly lower the filter then slide it back until it is in the proper position
Turn the power ON on the Control Panel. Check all lights and fan operation.
WARNING: Risk of electrical shock. This range hood must be properly grounded. Make sure this is done by a qualified electrician in accordance with all applicable national and local electrical codes. Before connecting wires, switch the power off to prevent the power from being switched on accidentally. Check with a qualified electrician if you are not sure that the range hood is properly grounded. DO NOT ground to a gas pipe. DO NOT have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short-circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.
IMPORTANT: Save this Installation Guide for the electrical inspector’s use.

RANGE HOOD USE

RANGE HOOD CONTROLS

JANSKA-Wall-Mount-Range-Hood-fig-13

OPERATING THE RANGE HOOD

To Turn the Fan ON press the Power Button and press the “+” button to increase the fan speed:
- Press “+” Once – Low (Digital Display shows F1)
- Press “+” Twice – Medium/Low (Digital Display shows F2)
- Press “+” Three Times – Medium/High (Digital Display shows F3)
- Press “+” Four Times – High (Digital Display shows F4)
To Delay Power OFF Function – while the fan is in working mode, press the Timer Button once. The digital display will blink, press “+” or “-” to increase or decrease delay time duration up to 15 min. The system will automatically shut off after the chosen time passes.
- To Turn the Light ON/OFF press the Light On/Off button once.
  NOTE: The fan and lights operate independently of each other.
- To Set the Time, press the Power button to turn it On, and then press and hold the Timer Button until Digital Display starts blinking. The Hour part will blink (00:00)
  Adjust the Hour by pressing the “+” for + hrs, or the “-” for – hrs. Once the Hour is correct, press the Timer button to save and switch to the Minutes. Set the minutes the same way (using the “+” and “-” buttons for + and – respectively).
- Press the Timer button to save time setting.
Remote Control Sensor:
The remote control sensor receives an infrared (IR) signal from the remote control. The maximum distance for IR data transmission is 20 feet and requires a direct line of sight. The transmission distance may vary depending on temperature and the remote control battery condition. Light settings are independent of other settings (including Power Off Delay) and lights have to be turned On/Off manually.
Note: The Remote Control is powered by a CR2025 battery.

REMOTE CONTROL

JANSKA-Wall-Mount-Range-Hood-fig-14

RANGE HOOD CARE

WARNING: To reduce the risk of electrical shock, DO NOT clean the hood while it’s operating.
WARNING: Never put your hands into the area housing the fan when the fan is operating.

CLEANING & MAINTENANCE
IMPORTANT: Clean the hood, grease tray, and baffle filters frequently according to the following instructions. The saturation of greasy residue in the exhaust vent and filters may cause increased inflammability. Always keep the unit clean and free of grease and residue build-up to prevent possible fires. DO NOT operate the Range Hood when filters are removed.

Exterior Surfaces
To avoid damage to the exterior surface, do not use steel wool or soap-filled scouring pads. Always wipe dry to avoid water marks.

Cleaning Method

Liquid detergent soap and water, or all-purpose cleaner.
Wipe with a soft damp cloth or non-abrasive sponge, rinse with clean water, and wipe dry.
For discolorations or deposits that persist, use a non-scratching household cleanser or stainless
Do not allow deposits to remain for long periods of time.
Stainless Steel Baffle Filters, Grease Tray, and Filter Spacers:
Filters, grease trays, and filter spacers should be cleaned frequently (every two months of operation, or more frequently for heavy use).
Remove all the parts mentioned above from the hood and discard oil and residue.
Wash the filters, grease tray, and filter spacers in the dishwasher, or soak in hot or warm water with dish detergent for half an hour, then wipe the filters clean. Repeat these steps until no oil residue remains.
NOTE: Stainless steel baffle filters, filter spacers, and grease trays are top-rack dishwasher safe.
Let the filters dry thoroughly.
Reinstall the grease tray, filter spacers, and baffle filters.

Replacing the LED Lights:
CAUTION! Disconnect from the power source before servicing.
ATTENTION: Wear gloves to protect against sharp edges.
CAUTION: LIGHTS AND SURROUNDING AREAS MAY BE HOT. REMOVE WHEN COMPLETELY COOL!

Unplug the range hood or turn off the breaker.
Remove filters. Reach into the interior of the range hood and locate the lamp. Gently squeeze the lamp clips on each side and push down until the lamp pops out. Remove and unplug.
Replace the LED lamp.
Push the lamp back into its place until secure.
Plug in the range hood, or turn on the breaker.

TROUBLESHOOTING

If the range hood or LED light does not operate after installation:

| Check if the range hood has been plugged in, make sure that all power has been turned back ON, fuse not blown and all electrical wiring are properly con- nected.
---|---
Swap out light assembly to working ones to deter- mine whether it is caused by defective bulbs. See Replacing the LED Lights on Page 15.
The range hood vibrates when the blower is on:| The range hood might not have been secured proper- ly on to the ceiling or wall.

The blower or fan seems weak:

| Check that the duct size used is at least 6 or 8 in. round (depending on the Range Hood model) or 3 1/4 x 10 in. rectangular.
Range hood WILL NOT function efficiently with insuf- ficient duct size. For example: 8 in. (20.3 cm) duct over 7 in. (17.8 cm) hole and loosely secured.
Check if duct is clogged or if damper unit (half-circu- lar flange) is not installed correctly or opening proper- ly. A tight mesh on a side wall cap unit might also cause restriction to the air flow.
The lights work but the fan is not spinning at all, is stuck or is rattling.| The fan might be jammed or scraping the bottom due to shipping damage.

The hood is not venting out properly.

| Make sure the distance between the stove top and the bottom of the hood is within 24 in. and 30 in. (61 and 76.2 cm) in distance, with minimum 30” for gas stove top.
Reduce the number of elbows and length of duct work. Check if all joints are properly connected, sealed, and taped.

SPECIFICATIONS

RHW-3687 (36in):

JANSKA-Wall-Mount-Range-Hood-fig-16

Body Design	Stainless Steel
Power Rating
Total Input Power	445W (218 Wx2 + 3x 3 W)
Motor Input Power	436 W
Amperage	4 A
Speed Control Levels	4 Speeds
Interference Protection	Radio Frequency Interference Protected
Motors	Twin Motors
Control	LCD Display Control, Remote Control
Filtration	Bafle filter
Illumination	3 x 3 W LED lights
Fan Type	2 x Single chamber quiet
Venting Size	Top, 8 inches (19.6 cm) round

JANSKA-Wall-Mount-Range-Hood-fig-17

Power: 120V/60Hz
Weight:

RHW-3687 (36in): 44lbs / 20kg
RHW-4813 (48in): 52.8lbs / 24kg

Baffle Filter size

RHW-3687 (36in): 13.3 x 14.6in
RHW-4813 (48in): 14 x 14.7in

Your purchase comes with a 100% satisfaction guarantee from Janska
If you are not happy with the product for any reason, please contact us at support@janskaus.com with your feedback or questions, and we will do our best to make things right for you! JANSKA USA 5175 Commerce Dr, Baldwin Park, CA support@janskaus.com