IpDoor IP7700 Monitor Interno Match User Guide

IpDoor IP7700 Monitor Interno Match

Product Information

IP7700 – Match Advanced

The IP7700 – Match Advanced is an indoor station with a 7-inch display that can be mounted on a surface. It provides a new interactive experience and can be connected to an external power supply. The device comes with a 2-pole cable and requires a stabilized power supply of 12VDC@1A type ICA0006 (not included). The device also has network settings and firmware that can be configured. It can be connected to a WiFi network or via LAN cable. The device can be installed on a wall using a built-in box.

Product Usage Instructions

Connecting to an External Power Supply

1. Use the supplied 2-pole cable to connect an external power supply.
2. Insert the connector, respecting the side guides, into the relative Power input (B) on the back of the monitor.
3. Use a stabilized 12VDC@1A power supply type ICA0006 (not supplied).
4. Referring to the 12V output of the power supply, connect the positive to input +12V (red) and the negative to input GND (black) of the two-pole cable plugged into the Power input (B) on the back of the monitor.

Connecting to a Network

To connect the monitor to a WiFi network:

1. Set the WiFi / CABLED selector to WiFi.
2. Press the word Network and select the one to which you want to connect the monitor from the available WiFi networks.
3. Enter the password to access the WiFi network and press OK.
4. Enabling the Wi-Fi connection will disable the connection via the LAN cable.

Installing on a Wall

To install the Match IP7700 monitor on the wall:

1. Wall up a 6cm diameter flush-mounted box at a height between 150 and 160 cm.
2. Secure the plate to the wall from the flat side with the supplied screws, making sure that the four fins protrude outwards.
3. Connect the network cable to the RJ45 port (A) on the back of the monitor.
4. If PoE 802.3af power is not used, connect the two-wire cable (Red / Black) to the power supply in the relative power port (B).
5. Place the monitor by inserting it from above.

External Power Supply Connection

• Power Interface
• Stabilized power supply 12VDC@1A
• Use the supplied 2-pole cable to connect an external power supply.
• Insert the connector, respecting the side guides, into the relative Power input (B) on the back of the monitor.
• Use a stabilized 12VDC@1A power supply type ICA0006 (not supplied).
• Referring to the 12V output of the power supply, connect the positive to input +12V (red) and the negative to input GND (black) of the two-pole cable plugged into the Power input (B) on the back of the monitor.

Add the monitor to a system

• The IP7700 Monitor is activated automatically after adding the device to a system.
• Check on the monitor screen that the dot is green and that there is therefore an internet connection.
• If necessary, access the NETWORK SETTINGS
• After adding the device to the system via the console, press ACTIVATE DEVICE on the monitor screen

Network settings

• To activate the monitor it is essential to be connected to a network with internet access.
• The device is factory set in DHCP to automatically receive the network settings from the router, in this case it is not necessary to set the device with a static IP.
• If, on the other hand, you want to proceed with the manual assignment of an IP address, disable DHCP and set the IP addresses according to your network parameters. If necessary, contact the network administrator to find out how to set the addresses.

WIFI settings

• To connect the monitor to a WiFi network, set the WiFi / CABLED selector to WiFi, then press the word “Network” and select the one to which you want to connect the monitor from the available WiFi networks.
• Enter the password to access the WiFi network and press OK.
• Enabling the Wi-Fi connection will disable the connection via LAN cable

IP7700 Wall installation

• The Monitor Match IP7700 is a device for indoor use only suitable for installation indoors.
• To install the Match IP7700 monitor on the wall, a 6cm diameter flush-mounted box must be walled up at a height between 150 and 160 cm.
• Secure the plate to the wall from the flat side with the supplied screws, making sure that the four fins protrude outwards.
• Place the monitor by inserting it from above, after connecting the network cable to the RJ45 port (A) on the back of the monitor and, if PoE 802.3af power is not used, the two-wire cable (Red / Black) to the power supply in the relative power port (B).

Installation with desktop bracket

• Using the ICA0020 accessory it is possible to use the IP7700 monitor resting on a desk.
• Attach the bracket supplied with the monitor to the desk base.
• Place the monitor in its bracket by inserting it from the top, after connecting the network cable to the RJ45 port (A) on the back of the monitor and, if the 802.3af PoE power supply is not used, the two-wire cable (Red / Black) for the power supply in the relative power port (B).

Dimensions

OUTPUT Connection

• Use the supplied 10-pole cable for the management of the OUTPUT.
• Insert the connector respecting the side guides, to the SIREN / ALARM (C) input located on the back of the monitor.
• The output identified between V+ (red) and GND (black) delivers, when activated, 12Vdc@100mA The OUTPUT1 output is factory set as a ringtone repeater and will be activated automatically when a call is received. This setting can be changed by the system administrator.
• complete the configurations on https://console.ipdoor.com

INPUT Connection

• Use the supplied 10-pole cable for the management of the INPUTS, insert the connector, respecting the side guides, to the SIREN / ALARM (C) input located on the back of the monitor.
• The inputs must be connected to a potential-free clean contact switch, the inputs supply a voltage of 5V@125mA and must all be referred to GND (black).
• ESEMPIO DI COLLEGAMENTO PULSANTE FUORIPORTA IN 1 (AL1) ED INGRESSO GENERICO IN 4 (AL4)
• EXAMPLE OF CONNECTION OF OUTDOOR BUTTON IN1 (AL1) AND GENERIC INPUT IN 4 (AL4)
• AL1 is set by the manufacturer to activate a notification sound on the monitor and cannot be changed.
• The inputs from AL2 to AL8 can be managed from the console as generic INPUTs with which an action can be associated.
• complete the configurations on https://console.ipdoor.com
• To configure the device and consult the complete documentation, access the administration console.
• https://console.ipdoor.com/
• Match declaration of conformity
• Available on
• www.ipdoor.com
• Manufactured by InfinitePlay S.r.l.
• Via Giacinto Andrea Longhin, 131 – 35129 Padova (PD) Italy

Documents / Resources

| IpDoor IP7700 Monitor Interno Match [pdf] User Guide
IP7700 Monitor Interno Match, IP7700, Monitor Interno Match, Interno Match, Match
---|---

References

• IpDoor: Videocitofono Smart | IpDoor
• console.ipdoor.com
• console.ipdoor.com/

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>