EasyPro PC18W Pro Clear UV Dual Outlet UV Clarifier Instruction Manual
- June 11, 2024
- EasyPro
Table of Contents
Dual Outlet UV Clarifier
Instructions for Operation Safety Warranty
PC18W Pro Clear UV Dual Outlet UV Clarifier
Thank you for purchasing the Pro-Clear™ UV Clarifier. Used with care, this
product can provide years of service. Ultraviolet light is a wavelength of
light that inhibits algae growth from reproducing. Ultraviolet light is not
designed to kill string algae. Please read this instruction booklet carefully
before use to assure that you safely and correctly use this product.
PART#| DESCRIPTION| MAXIMUM FLOW| MAXIMUM POND SIZE|
QTY/ SIZE BULB| CORD LENGTH| INLET/OUTLET SIZES
---|---|---|---|---|---|---
PC18W| 18 Watt UV Transformer| 2100 GPH| 4000 Gallons| 1| / 18 Watt| 6′| 0.75″
/| 1″ /| 1.25″ /| 1.5′
PC36W| 38 Watt UV Transformer| 3900 GPH| 7000 Gallons| 1| / 36 Watt| 6′| 0.75″
/| 1″ /| 1.25″ /| 1.5″
Safety & Warnings
-
Be sure to read and follow ALL safety instructions.
-
Always disconnect the electrical supply before handling, maintaining, repairing or installing any pond equipment. Do NOT immerse or attempt to use a wet plug.
-
DANGER: Direct exposure to ultraviolet (UV) light can damage eyes and skin.
Do NOT attempt to view the lamp when lit, except through the sight glass viewer on the end of the unit. -
ONLY connect this product to a receptacle protected by a Ground Fault Circuit Interrupter (GFCI).
-
Do NOT use if power cord is damaged. Damaged cords should be repaired or replaced.
-
All electrical work must be performed by a qualified technician. Always follow the National Electrical
Code (NEC) or the Canadian Electrical Code (CEC) as well as all local, state and provincial codes. Code questions should be directed to your local electrical inspector. Failure to follow electrical codes and OSHA safety standards may result in personal injury or equipment damage. Failure to follow the manufacturer’s installation instructions may result in electrical shock, fire hazard, personal injury or death, damaged equipment, provide unsatisfactory performance and may void manufacturer’s warranty.
Unpacking & Installation
WARNING: Disconnect the unit from power source before performing any
maintenance or installation on the unit.
CAUTION: Do not install unit on the ground where water may puddle. Do not
submerge the UV unit.
- Before unpacking the UV unit, visually check to see that the product is not damaged in the packaging.
- The UV bulb and quartz sleeve are already installed in the unit.
- Carefully remove the UV unit from the package. (FIGURE 1)
- Open the parts bag that contains the rubber gaskets (sealing rings), plastic nuts and barbed connectors. (FIGURE 2)
- Size your tubing (FIGURE 3) and precut your barbed connectors (fittings) before installing onto unit. Do not attach tubing to the connectors at this time.
- Making sure that the rubber gaskets are installed in the nuts, attach the barbed connectors to the main unit. (FIGURE 4)
- On a secure platform, the UV unit can be installed horizontally or vertically on it’s mounting brackets. Attach the tubing to the connectors.
- Connect the power to the UV light and the water pump. Making sure the pump is running, ensure bulb is operational by looking into the sight glass on the end of the unit. This provides a safe way to see if the light is on. (FIGURE 5)
UV Installation & Maintenance
WARNING: Disconnect the unit from power source before performing any
maintenance or installation on the unit.
CAUTION: Do NOT operate or handle the UV bulb outside of the housing.
Ultraviolet radiation is harmful to eyes and skin and can cause serious
injury.
Note: UV bulb and quartz sleeve should be handled carefully. These parts are
not warrantied for breakage or damage.
For servicing bulbs or sleeves, after previous use, be sure to drain water
from the UV housing.
Replacing the UV Bulb
-
Unscrew threaded cap from unit. (FIGURE 6)
-
Slide UV bulb partially out of the unit. Disconnect the socket from the bulb by compressing the metal tabs in the socket and gently rocking and slowly pulling the bulb from the socket. (FIGURE 7)
-
Remove the bulb from the unit. Disconnect the spacer from end of old bulb and secure it to the end of new bulb. (FIGURE 8)
-
Insert new bulb into the housing, leaving approximately 4″ outside of the unit. Be sure to insert bulb straight and avoid angles, as this can damage the quartz sleeve. Do NOT force bulb in the unit. (FIGURE 9)
NOTE: Do NOT touch the bulb with your bare fingers, as this will shorten the life of the bulb. Use gloves or a cloth to hold the bulb.
Clean the bulb with denatured alcohol and a clean, soft cloth if you do happen to touch the bulb. -
Securely connect the socket to the bulb. Line up socket hole and safety pin (FIGURE 10) located on the inside of the quartz sleeve and insert bulb fully into the unit.
-
Hand tighten the threaded cap back onto the unit, making sure not to overtighten. Double check to make sure all threaded fittings are tight. (FIGURE 11)
-
Before turning the UV unit back on, let the water run for a few minutes to ensure there are no leaks.
-
Once no leaks have been detected, plug the transformer (ballast) into a GFCI outlet.
Replacing or Cleaning the Quartz Sleeve
-
Follow steps one through three from UV bulb installation above.
-
Carefully remove the quartz sleeve from the housing.
-
To clean the quartz sleeve, various deposit removal cleaners can be used (vinegar, CLR, Lime-Away, etc.) DO NOT use any abrasive products as it may scratch the sleeve.
Rinse thoroughly. -
To replace or reinstall the quartz sleeve, simply insert the new sleeve back into the housing, being sure the end is seated properly in the end of the unit. (FIGURE 12)
-
Follow steps four through eight for reinstalling UV bulb, securing the unit and testing for leaks from the above UV bulb installation instructions.
Replacement Parts
EasyPro Pond Products Limited Warranty
EasyPro Pond Products (“EasyPro”) warrants to the purchaser that this product
(“Product”) will be free from any mechanical or material defects for a period
of:
Housing: Five years from the date of purchase.
Transformer, Sleeve, Bulb: One year from the date of purchase. Broken UV bulbs
or sleeves are not covered under this limited warranty. This warranty only
covers properly installed and maintained Products sold by authorized EasyPro
Sellers who are subject to and follow EasyPro’s quality control standards.
Please note that because EasyPro is unable to control the quality of Products
sold by unauthorized sellers, unless otherwise prohibited by law, this
warranty does not cover Products purchased from unauthorized sellers.
This warranty does not cover normal wear and tear, nor any deterioration
suffered through overloading, improper use, negligence, improper installation,
acts of God or accident. Similarly, any modification made by the purchaser to
the Product will cause the warranty to be null and void. This warranty does
not cover any cost associated with the installation or removal of the Product
subject to a warranty claim.
All returned items will be inspected to determine cause of failure before a
warranty claim is approved.
The exclusive remedies provided hereunder shall, upon EasyPro’s inspection and
option, be either repair or replacement of the Product or parts covered under
this warranty.
Making a Claim: A Return Authorization (“RA”) number must first be obtained by
calling EasyPro at 800-448-3873 or via
email at warranty@easypro.com. It is the
purchaser’s responsibility to pay the return shipping charges. Be sure to
include the RA number, original receipt (in the form of an invoice or sales
receipt), your name, your return address and your phone number inside of the
package. No warranty claims will be honored without the original receipt that
shows that your purchase was made from an Authorized EasyPro Seller. Ensure
the product is properly packaged and insured for the replacement value. Damage
due to improper packaging is the responsibility of the sender.
ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING MERCHANTABILITY OF FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED IN DURATION TO THE DURATION OF
THE WARRANTY AS DESCRIBED ABOVE. Some States do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply to
you.
EasyPro shall not be held liable for any damages caused by defective
components or materials of this Product; or for loss incurred because of the
interruption of service; or any consequential/incidental damages and expenses
arising from the production, sale, use or misuse of this Product. Some States
do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
EasyPro shall not be held liable for any loss of fish, plants or any other
livestock as a result of any failure or defect of this Product. This warranty
gives you specific legal rights, and you may also have other rights that vary
from state to state.
****800-448-3873
Grant, Michigan
www.easypro.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>