power adhesives tec 806-12 Applicatore Hot Melt Instruction Manual
- June 11, 2024
- power adhesives
Table of Contents
tec 806-12 • tec 806-15
tec 806LT-12 • tec 806LT-15
Operating Instructions Hotmelt Applicator
Please read carefully before attempting operation
Instruction Manual
SECURITY INST.
Do not touch the nozzle or the molten one adhesives with bare skin because
they are hot operating temperature this Tools Yippee approximately 200°C/392°F
(LT 120°C/ 248°F).
Always would with they had use protective glove.
Careless manipulation can cause burns skin.
If with melted adhesive will get to contact with skin, immerse disabled place
immediately to a big one amount cold water.
IN the case needs look for medical Help.
Except here listed security instructions Yippee for example at usage this tool
adhere to all legal regulations, local regulations O fire insurance or other
in general valid “regulations for prevention injuries”.
Repairs may to perform only competent workers with corresponding
electrotechnical knowledge.
Before starting work with any maintenance or repair, disconnect tool from
electrical networks. from electrical networks.
IN the case doubts with turn over on your own suppliers.
– WARNING – This tool must be placed on own when with does not use; don’t
leave tools on the stand. unattended if on.
– After using the tool, place it on the stand and before storing to cool down.
– Never use the tool if it is however damaged. damaged in any way. if it is
supply cable damaged, it must be be replaced by the manufacturer, its service
or similarly qualified persons, that danger averted.
– Do not use this tool while under the influence drugs or alcohol.
– Do not use this tool in damp rooms, namely do not expose to rain, moisture
or submerge in water. water.
– Do not use this tool near any materials sensitive to heat or any flammable
materials. materials, liquids or gases, and do not use in the same place for a
long time. vertebrae
– Use only extension cables with cross section conductors 1.5 mm² / 16 a.w.g.
and with a maximum length of 20 m / 65 feet.
– Depending on the country, this tool may be equipped polarized plug, intended
to be inserted into polarized sockets. If the plug completely does not fit
into the socket, turn the plug. If still does not fit, contact the
manufacturer. Tool plug do not modify in any way. Never pull on the power cord
tool cable.
– This tool can be used by children from the age of 8 and persons with reduced
physical, sensory or mental abilities or lack of experience or knowledge only
if they have been provided with supervision or have been instructed in safe
use appliance and understands the resulting dangers.
– Children must not play with the appliance. Cleaning a user maintenance must
not be carried out by children without supervision.
Traversing the problem
- Before starting work, make sure that the tool has reached temperature.
– Do not leave the tool switched on for a long time without use you will not be using the tool for more than 40 minutes, turn it off and turn on again when necessary.
– Never lay the tool on its side. Always use the one supplied stand, optional table stand or hanging unit.
– Use only adhesives designed for use with this tools.
– Never remove a partially used glue stick. He can it lead to irreparable damage.
– Can be used instead of nails, staples, tapes and liquid glues hot melt adhesive. However, it should not be used instead structural joints under heavy load.
– Do not use hot melt glue on objects that are exposed to extreme heat. Some adhesives that can used in this tool, they soften at 60°C.
Do not connect to the mains at this point!
- Attach the tool stand1
- Load the tool by inserting a glue stick into it. rear parts 2
- Use the trigger to move the stick forward until it is resistance is felt3
- Connect to the main power supply and turn on the tool4
- Wait 5 minutes for it to heat up
- Extrude the glue with the trigger until the stick is completely pulled into the back of the tool.
- Insert a new stick2 into the tool
- To turn off the tool, disconnect it from the mains
GUARANTEE AND REPAIRS
This tool is guaranteed against faulty workmanship and materials for a period
of 12 months from the date of purchase. Within this warranty period the
manufactur- ers undertake, at their discretion, to either repair or replace
any tool proved to be defective (proof of purchase will be required for
verification). This guarantee is invalidated if the tool is opened, or
modified in any way, or if adhesive formulations other than those supplied by
the tool’s manufacturer are used. Warranty claims attributable to improper, or
careless, use or handling, and to normal wear, are excluded from this
guarantee.
The supplier’s and manufacturer’s only obligation shall be to replace such
tools that are proved to be defective. Neither supplier nor manufacturer shall
be liable for any injury, loss or damage, direct or consequential, arising out
of the use, or the inability to use, this tool. The user shall determine the
suitability of this product for its intended use, and the user assumes all
risks and liability whatsoever in connection therewith.
The manufacturer reserves the right to improve or modify this product without
prior notice.
**** Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your authority for information regarding the collection systems available. If electrical appliances are disposed of in landfill or dumps, hazardous substances can leak into the groundwater and get into the food chain, or the flora and fauna can be poisoned for years during the weathering. When replacing old appliances with new ones, the retailer is legally obliged to take them back for disposal at least, free of charge.
Power Adhesives Ltd.
Basildon, Essex, England
SS13 1TN
Telephone: +44 (0) 1268 885 800 Facsimile: +44 (0) 1268 885 810
sales@poweradhesives.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>