Master Kitchen 330364 Retro Rangehood Instruction Manual
- June 4, 2024
- Master Kitchen
Table of Contents
INSTALLATION INSTRUCTIONS
USER GUIDE
RETRO RANGEHOOD
330364
To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time
RECOMMENDATIONS AND SUGGESTIONS
The instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.
- The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
- Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
- For Class I appliances, check that the domestic power supply guarantees adequate earthing.
- Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible.
- Do not connect the extractor hood to exhaust ducts carrying combustion flumes (boilers, fireplaces, etc.).
- If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in orderto avoid a hazard.
- The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels(notapplicable to appliances that only discharge the air back into the room).
- The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood is 650 mm.
Regulations concerning the discharge of air have to be fulfilled.
USE
- The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
- Never use the hood for purposes other than for which it has been designed. Never leave high naked flames under the hood when it is in peration. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
- Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
- There is a fire risk if cleaning is not carried out in accordance with the instructions. Do not flame under the range hood.
- CAUTION ” : Accessible parts may become hot when used with cooking appliances”.
MAINTENANCE
- The cooker hood and its filter should be cleaned regularly according to the instruction.
- Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
- Clean the hood using a damp cloth and a neutral liquid detergent.
- The appliance uses 4 hob elements at most.
The symbol is packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
COMPONENTS
Ref. | Qty. | Product Components |
---|---|---|
1 | 1 | Hood Body, complete with: Controls, Light |
Blower, Filter.
2.| 1| Lower Decorative Chimney
2.| 1| Upper Decorative Chimney ( optional )
3| 1| Flange ( optional )
4| 1| Exhaust Pipe
5| 2| The Activated Charcoal filter ( optional )
Qty. | Documentation |
---|---|
1 | Instruction Manual |
Ref. | Qty. | Optional Installation Components |
---|---|---|
10 | 7 | Screws 5 x 50 |
11 | 7 | Wall Plugs |
12 | 6 | Screws 4,2 x 9,5 |
20 | 1 | Hood fixing bracket |
21 | 1 | Chimney fixing bracket ( optional ) |
Option | Chimney | A | B | Height |
---|---|---|---|---|
1 | 400+0 | 628 | / | 628 |
2 | 400+300 | 628 | 670-910 | 628-910 |
3 | 400+390 | 628 | 670-1000 | 628-1000 |
4 | 500+490 | 728 | 770-1200 | 728-1200 |
INSTALLATION
WALL DRILLING AND BRACKET FIXING
Option | Chimney | X |
---|---|---|
1 | 400+0 | / |
2 | 400+300 | 390-620 |
3 | 400+390 | 390-710 |
4 | 500+490 | 490-910 |
As a first step, proceed with the following drawings:
- A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
- A horizontal line A at 920-1020 mm above the cooker top.
- A horizontal line B at a X mm above the horizontal line A.
- A horizontal line C at a 190mm below the horizontal line A.
Mark Points:
- Mark a point (1) on the horizontal line A, 80 mm to the vertical reference line.
- Repeat this operation on the other side and on the vertical reference line , checking that the three marks are leveled.
- Mark a point (2) on the horizontal line B, 40 mm to the vertical reference line.
- Repeat this operation on the other side , checking that the two marks are leveled.
- Mark a point (3) on the horizontal line C, 170 mm to the vertical reference line.
- Repeat this operation on the other side , checking that the two marks are leveled.
Fix the brackets :
- Drill holes at the marked points with a ɸ10 mm drill bit.
- Insert the Wall Plugs 11 into the holes.
- Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A.
- Fix a Chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.
Hook the hood body
Hook the hood body to the bracket 20.
Level the hood body itself.
Remove the filter from the inside of the hood body, fix the screws 10 to Wall
Plugs 11 at the points (3).
CONNECTIONS
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using
either a flexible or rigid pipe ɸ 150 or ɸ 120 mm, the choice of which is left
to the installer.
- If to install a ɸ 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.
- Fix the pipe 4 in position using sufficient pipe clamps (not supplied).
- Remove possible charcoal filters.
CHIMNEY ASSEMBLY
Lower Decorative Chimney
- Fix the Lower Decorative Chimney to the hood body with 2 screws 12 (4.2 x 9.5) supplied with the hood.
Upper Decorative Chimney
- Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood.
USE
Speed adjustment. (For some models)
| OFF MOTOR SWITCH: Press on this switch to stop the motor operation.
---|---
| SPEED SWITCH: Press on this switch, the motor runs at LOW speed.
| SPEED SWITCH: Press on this switch, the motor runs at MEDIUM speed.
| SPEED SWITCH: Press on this switch, the motor runs at HIGH speed.
| ON/OFF LIGHTING SWITCH: Press on this switch to turn on the lights, and
press again to turn them off.
MAINTENANCE
GREASE FILTERS
CLEANING METAL SELF-SUPPORTING GREASE FILTERS
- The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
- Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
- Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency).
- When fitting the filters into the hood pay attention that they are mounted in correct position , the handle facing outwards.
ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION)
These filters are not washable and cannot be regenerated, and must be replaced
approximately every 4 months of operation, or more frequently with heavy
usage.
REPLACING THE ACTIVATED CHARCOAL FILTER
- Remove the metal grease filters
- Remove the saturated activated charcoal filter.
- Fit the new filters.
- Replace the metal grease filters.
LIGHTING
LIGHT REPLACEMENT(Completed by professionals)
Replacing the light modules
- You cannot replaced the light bulbs, the entire light module has to be replaced.
- When changing the light modules, the contacts are live.
- Before changing the light module(s), unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
- Remove the grease filter .
- Disconnect the terminal of LED light.
- Press LED light on the back of the front plate, take the LED light out.
- Replace the lamp(commercially available LED lamp (max.1.5w).
Lamp type | Max Power | Voltage | Picture | Lamp Cap | ILCOS D code |
---|
LED modules,
separate ballast| 1.5W| DC 12 V| CI)
Round/ Diameter: 70mm| —| DSR-1.5-5-70
Reinstall LED light module
- Press LED light on the front of front plate, install the LED light on the front plate.
- Connect the terminal of LED light and light leads.
- Reinstall the grease filter.
TROUBLE SHOOTING
Fault | Cause | Solution |
---|---|---|
Light on, but motor does not work | The blades are blocked. | Check the blades. |
The capacitor is damaged. | Replace capacitor. | |
The motor is damaged. | Replace motor. |
The internal wiring of motor is cut off/ disconnected. An unpleasant smell may
be produced.| Replace motor.
Both light and motor do not work| Apart from the above-mentioned, check the
following:
Light damaged.| Replace lights.
Power cord loose.| Connect the wires as the electric diagram.
Oil leakage| Outlet and the air ventilation entrance are not tightly sealed.|
Take down the outlet and seal with glue.
Vibration| The blade, if damaged, can cause vibrating.| Replace the blade.
The motor is not tightly fastened.| Fasten the motor tightly.
The cooker hood is not tightly fixed.| Fixed the cooker hood tightly.
Insufficient suction| The distance between the cooker hood and the cooker top
is too large.| Readjust the distance.
Too much ventilation from open doors or windows.| Choose a new place to
install the appliance or close some doors/windows.
The
machine i nclines| The fixing screws are not tight enough.| lighten the
fixing screw and make it horizontal.
The hanging screws are not tight enough| lighten the hanging screw and make it
horizontal.
DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order to optimize the recovery and recycling of the
materials they contain, and reduce the impact on human health and the
environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance, it must be separately
collected. Consumers should contact their local authority or retailer for
information concerning the correct disposal of their old appliance.
P/N:16173000A18830
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>