waytronic WT-M12 MicroSound Voice Prompter Instruction Manual
- June 4, 2024
- waytronic
Table of Contents
waytronic WT-M12 MicroSound Voice Prompter Instruction Manual
Product features
- Small and exquisite, playing MP3 audio with excellent sound quality.
- Two levels volume for option, small or maximum.
- Human body induction, induction distance within 4 meters.
- Using WT2003 voice chip solution, unrepeatable triggering pulse.
- Standard 32Mbit SPI-flash, available to replace capacity according to customer requirements.
- A and B buttons are corresponding to the previous audio, the next audio.
- Power-down memory function.
- Micro USB interface.
- Support to replace the audio files of SPI Flash through USB interface on computer.
- 3 AAA batteries or USB for power supply.
- Built-in 8Ci1 watt speaker.
Electrical parameters
| Power supply mode | DC3V 5V stabilized voltage supply |
|---|
Working Current
| Sleep standby mode| S100uA
Playing mode| S130mA(DC4.7V)
Audio Format| MP3| Bit Rate. 8-320Kbps
Audio Output Power| 8lD/1W(typical value)
Infrared Induction Range| s4m(120°Angle)
Appearance introduction
This product is easy to use. Support voice file replacemencomputer through USB
interfaoe, but not support to read SD card. It includes a micro USB interface,
two keys A and B, a slide switch.
Micro USB imterface is used connecting power adapter to supply power for the
device,or connecting computer to download audio.SD card slot is spare,not used
in this version.
| Slide Switch | To the bottom | Switch off |
|---|---|---|
| To the middle | Small volume | |
| To the top | Maximum volume | |
| Playing indicator light | Light off | Power oP or no voice playing |
| Light on | Voice playing | |
| Button A | Short press | Play the previous audio |
| Long press | Switch to A/B mode: Indicator light flashes once,means it is A |
mode(loop sequence ), flashes twice means it is B mode(single playback).
Button B| Short press| Play the next audio
Micro USB interface| Connect DCSV power adapter or computer| Supply power;
download audio files.
Note:
- When switch on, wait about 20S, then it can work normally. Within 4 meters, when people or animal walk by, it will trigger the sensor to play voice.
- Each time, after triggering to play voice, you need to wait 2S, then it can trigger again to play voice.
- Each time, after triggering, go out of the induction range and enter the range again, then it can have a better effect of the next trigger.
- In B mode, you only need to short press key A or B to select audition of the triggering voice, need no other operations.
- Key function is only valid during the process of voice playing. If no voice play, it’s invalid to press key.
- If plug in the power, please remember to remove the batteries to avoid unexpected accidents.
Audio download
It’s easy to replace audio files. Just use USB cable to connect to computer, here will appear a drive. You just need to copy audio files into this drive.
Note:
- The audio file size should be not more than internal FLASH capacity. Only support MP3 audio format.
- After copying is complete, sometimes play a section voice. When finishing the voice play, 3 seconds later, it can trigger and play again.
- You can copy any voice, tones, music, into this product, as long as the format is MP3, within memory capacity. Besides, you can make your own personalized voice.
Brief operadon introduction
How to replace voice files:
- Convert the voice into MP3 format.
- Connect to computer by USB cable. Computer will automatically appear a “removable disk”.
- Format the “removable disk”.
- Open it by double-clicking, choose voice files to copy.
-
lnfrared principle: the temperature of induction area rises suddenly, then trigger induction. Only suitable for indoor use.
-
If environment temperature is over 30’C, infrared induction distance will be shortened, which is a
normal phenomenon. -
If environment temperature is over 37“C, infrared induction will be invalid, because human body temperature is 37°C, so it cannot sense.
Induction distance too short
Reason 1: low battery (you can use regular alkaline batteries)
Reason 2: environment temperature too high, influences its induction
distance.
Reason 3: after playing a section voice, there will be 3 seconds
interval. Wait 3s, then it can trigger and
Reason 4: When testing, if parallel with infrared ray, it will be unable
to trigger effectively. You should walk from the left of device to the right,
from a cross with interfered ray them it can trigger.
Normal induction distance is 0-3 meters. If the temperature is high, induction distance is about 2 meters.If there is electric fan or air conditioner blowing, influenoe on the temperature of induction area, it can trigger to play voice.
So you’d better to choose the environment to test where there is no electric fan or air conditioner blowing.
Installation
Side wall mounted
About 1.5 meters above the ground is the best.
About 1 meter far from the door-frame. Use the mounting holder to fix the
device, toward the door, 45°(see picture).
InstaIIed on the top of the door
About 2 meters above the ground is the best. Lay across, paralleled with door- frame. If door-frame is wide, installed crosswise.
Detailed installation depends on the environment, just installed where people
pass by. It can be used
for reminding, sales promotion, doorbell, visitor welcome, etc
Support
Head office: Shenzhen Waytronic Electronics Co., Ltd.
Tel:+86-(0755) 29605099
E-mail: WT1999@waytronic.com
Web: en.waytronic.com
waytronic.aliexpress.com
Add: 4th Floor, Building No.11, COFOC (Fu’an)
Robotics Industrial Park, Dayang Road No.90,
Fuyong Town, Bao’an District, Shenzhen,
Guangdong, China.
FAQ
Q1. Why is there no sound when the human body induction is turned on?
Answer:
1 Please check whether the product successfully copied the voice;
2 Please confirm whether the voice file is correct and whether the voice size
is greater than the storage capacity of the product. This product comes
standard with 4M memory, supports MP3 format audio files, bit rate:
16-320Kpbs, 128Kpbs is recommended; (the total voice content should be less
than 4 minutes ).
Q2. What power supply method does the product use?
Answer: This product is powered by a 5V USB power adapter or 3 AAA dry batteries (note that when a USB testing, if parallel with infrared ray, it will be unable to trigger effectively. You should walk form the left of device to the right, forming a cross with infrared ray, then it can trigger.
Q3. Why can’t I download the voice when I connect to the computer via Micro USB?
Answer :
1 Please make sure that the Micro USB cable is a 4PIN data cable.
2 After the product is connected to the computer, it needs to wait about 6
seconds to successfully read the disk.
Q4: Why are there situations such as non-reporting, false alarming, and too close sensing distance?
Answer:
1 The product needs to wait 6 seconds for power-on initialization before it
can work normally.
2 This product adopts the principle of infrared pyroelectric induction, and
the working temperature is 0-33 C , which is easily affected by changes in
ambient temperature. Please do not approach air conditioners, fans, and other
places with large temperature differences.
3 If the voltage of this product is too low, it will work unstable. Please
confirm whether the battery is dead.
Q5. Why is there a stuttering or intermittent phenomenon when playing a voice?
Answer:
1 Please confirm whether the bit rate of the MP3 audio file is within the
range of 16-320Kpbs.
2 Please check whether the battery power is insufficient. If the voltage of
this product is too low, it will work unstable. Please replace the battery in
time.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>