realme RMX3630 10 Smartphone User Guide

realme RMX3630 10 Smartphone

Product Information

The realme mobile phone (model RMX3630) comes with a 16.3cm (6.4″) display and a 50Megapixels+2Megapixels rear camera, along with a 16Megapixels front camera for selfies. It has a 5000mAh/19.35Wh (typical) battery and comes with standard accessories such as a charger, USB data cable, SIM ejector tool, protective case, safety guide, and quick guide. The phone is compliant with FCC regulations and has been tested to ensure compliance with Specific Absorption Rate (SAR) limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission.

Product Usage Instructions

To transfer content from an old phone to the new realme phone, you can use the realme Clone Phone feature. If the old phone is an Android device, you need to scan the QR code provided in the user manual and download the Clone Phone app. Next, install the app on both old and new phones and follow the on-screen instructions to complete the operation. If the old phone is an iPhone, open Clone Phone on the new phone and follow the on-screen instructions to sign in to your iCloud account and sync the files.

The phone comes with a non-removable back cover. It has a power key and volume key for easy navigation. To charge the phone, use the provided charger and USB data cable. FCC regulations caution that the device should not cause any harmful interference and must accept any interference received, including that which may cause undesired operation. Any changes or modifications not approved by the compliance party may void the user’s authority to operate the equipment.

The phone supports various radio frequencies such as GSM, WCDMA, LTE FDD, and LTE TDD. It also supports Bluetooth, 2.4G Wi-Fi, 5G Wi-Fi, and NFC. The radio waves specifications include different frequency bands and maximum output power for each band. The phone is compliant with SAR limits set by FCC and ANSI/IEEE C95.1-1992 for general population/uncontrolled exposure limits.

Greetings from realme mobile

This guide will show you how to use the phone and its important functions. You may also visit realme official website to get more information about the phone.

Warning

• Do not place the phone or battery near or inside heating equipment, cooking equipment’s, high pressure vessels (such as microwave ovens, induction cooker, electric oven, heater, pressure cooker, water heater, gas stove, etc.) to prevent the battery overheating which may lead to an explosion.
• The original charger, data cable and battery shall be used. Unapproved chargers, data cables, or batteries that are not certified by the manufacturer may result in electric shock, fire, explosion, or other hazards.
• Back cover can’t be removed.
• When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with temperature ranging from 5°C~35°C.

How to reboot the phone

Press and hold the Power Button and Volume Up Button at the same time until the realm boot animation is displayed to reboot the phone.

How to Transfer Old Mobile Content to a New Mobile

You can use realme Clone Phone to easily transfer photos, videos, music, contacts, messages, apps, etc from your old phone to the new one.

1. If you have an old Android phone, first scan the QR code below, then download and install Clone Phone, next open Clone Phone on both the new and old phones, and follow the on-screen instructions to complete the operation.
   https://i.clonephone.coloros.com/download

2. If you have an old iPhone, open Clone Phone on the new phone directly, and follow on-screen instructions to sign in to iCloud account and sync the files.

Standard accessories

You are provided with the following standard accessories:

• 1Phone,
• 1 Charger,
• 1 USB data cable,
• 1 Safety Guide,
• 1 Quick Guide,
• 1 SIM Ejector Tool,
• 1Protective Case.

Specification

Radio Waves Specifications

Radio| Frequency| Max. Output Power

GSM

| 850MHz/900MHz| 33.5dBm
1800MHz/1900MHz| 30.5dBm

WCDMA

| Bands 1/5/8| 24.5dBm
Bands 2/4| 24dBm

LTE FDD

| Bands 1/3/66| 24dBm
Bands 2/4| 23.5dBm
Band 7| 23.5dBm
Bands 5/8/12/13/17/20/28| 24.5dBm
LTE TDD| Bands 38/40/41| 24dBm
Bluetooth| 2.4-2.4835GHz| 14dBm(EIRP)
2.4G Wi-Fi| 2.4-2.4835GHz| 21dBm(EIRP)

5G Wi-Fi

| 5.15-5.35GHz; 5.47-5.725GHz| 19.5dBm(EIRP)
5.725-5.85GHz| 20.5dBm(EIRP)
NFC| 13.56MHz| 42dBuA/m @10m

FCC Regulations

This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Note

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

RF Exposure Information (SAR)
This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the separation of 1.5 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.
This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2AUYFRMX3630
For this device, the highest reported SAR value for usage against the head is 1.00 W/kg, for usage near the body is 0.83W/kg.

While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirements.
SAR compliance for body-worn operation is based on a separation distance of XX mm between the unit and the human body. Carry this device at least XX mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body-worn operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of XX mm between this device and your body.

RF exposure compliance with any body-worn accessory, which contains metal, was not tested and certified, and use such body-worn accessory should be avoided.

Regulatory
Steps to search E-label : Go to Settings -About Phone – Certificate Information.

References

• i.clonephone.coloros.com/download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>