Trust 71034 Wireless Dusk-Dawn Sensor User Manual

: June 9, 2024
: Trust

Table of Contents

1. Install transmitter batteries
2. Assign code to a Trust Smart Home receiver
3. Set switch-off delay
4. Close battery cover and snap on the foot stand
5. Set light level for the ON signal
6. Place transmitter indoor or outdoor
7. Delete code from Trust Smart Home receiver memory
Safety Instructions
Declaration of Conformity
TECHNICAL SPECIFICATIONS
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trust 71034 Wireless Dusk-Dawn Sensor

1. Install transmitter batteries

Detach the foot stand with a screwdriver.
Remove the screws to open the battery compartment.
Place 2x 1,5V AAA alkaline batteries in the battery compartments. The polarity should match the symbols on the holder.

2. Assign code to a Trust Smart Home receiver

Program the code of this transmitter into the memory of one or several Trust Smart Home receivers.
Slide the LEARN switch from [DEL] to [SET] to send an ON-signal. Read the receiver’s manual for the code learning procedure.

3. Set switch-off delay

At the “0” setting, the transmitter will send an OFF-signal once a certain light level has been reached (see: “Set light level”). At the 2h-8h setting, the transmitter will automatically send an OFF-signal after 2 up to 8 hours after the ON-signal.

4. Close battery cover and snap on the foot stand

Tighten all screws to ensure waterproofness. Damaging or removing the rubber seal inside the housing can lead to leakage.

5. Set light level for the ON signal

To set the light level, press and hold the [START] button for 3 seconds. The current light level will be stored and the LED on the front will flash 16 times. When the sensor registers the set light level, it will send an ON signal to the receivers it has been assigned to.

6. Place transmitter indoor or outdoor

Use the foot for horizontal placement or use the rear slots for wall mounting. It takes approximately 30 seconds before the product is operational.

7. Delete code from Trust Smart Home receiver memory

Read the receiver’s manual for the single code deletion procedure. Slide the LEARN switch from [SET] to [DEL] to send an OFF-signal.

Safety Instructions

Product support: www.trust.com/71034 . Warranty conditions: www.trust.com/warranty
To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety
The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete
Never use Trust Smart Home products for life-support systems. This product is water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -1.33 dBm. Radio transmission frequency range: 433,92 MHz

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.
Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.
Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.
Trust Electronics Ltd. declares that item number 71034/71034-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance
Trust International B.V. declares that item number 71034/71034-02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:
Model: ABST-604 Wireless dusk/dawn sensor
Item number: 71034/71034-02
Intended use: Indoor/Outdoor

is in compliance with the essential requirements and other relevant provisions of the following directives:
ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)
The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

TECHNICAL SPECIFICATIONS

Codesystem	Automatic
Power	2x AAA 1.5V alkaline battery (not included)
Size	HxWxL: 87 x 59 x 27 mm
IP rating	IP-56
Turn Off Timers	after 2/3/4/5/6/7/8 hour or when it gets light

Customer Service

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com
Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change without prior notice. Made in China.