OMNIVISION OH0TA10 Medical Image Sensor Owner’s Manual
- June 9, 2024
- OMNIVISION
Table of Contents
OMNIVISION OH0TA10 Medical Image Sensor
OMNIVISION’s OH0TA is an OVMed® medical-grade image sensor with a package size of just 0.55 mm x 0.55 mm, featuring a 1.0-micron pixel and a 1/31” optical format. The OH0TA takes medical visualization to the next level by quadrupling the RGB image resolution of its predecessor to 400 x 400, or 160 Kpixels, at 30 frames per second, while reducing the power consumption by 20% to 20 mW. This allows designers to add ultra-compact visualization to single-use and reusable endoscopes, as well as catheters and guidewires, with a small outer diameter of 1-2 mm.
The OH0TA’s increased resolution improves the visualization of tissues and other fine details inside the human body, allowing surgeons to see crisper images during procedures such as neuro, ophthalmic, ENT, cardiac, spinal, urology, gynecology and arthroscopy, as well as dental and veterinary diagnosis and surgery. Additionally, the sensor’s lower power consumption reduces “chip on tip” camera heat for greater patient comfort and longer procedure durations, while reducing noise.
To achieve this increase in resolution, along with a smaller pixel size and optical format, the OH0TA is built on OMNIVISION’s PureCel®Plus-S stacked die technology. This next-generation pixel technology also provides higher color fidelity and excellent low light sensitivity of 3600 mV/lux-sec, along with a high signal-to-noise ratio of 37.5 dB for greater image quality. Additionally, PureCel®Plus-S enables the OH0TA’s higher full well capacity (FWC), zero blooming, and lower power consumption, resulting in better patient outcomes.
Other key features include a 15.5-degree chief ray angle, enabling the use of lenses with high fields of view and short focus distances. It also supports a 4-wire interface, as well as raw analog data output, both of which can transmit via cables as long as 4 meters with minimal signal noise. The OH0TA sensor also interfaces with OMNIVISION’s existing OV426 analog-to-digital- conversion bridge chip for backward compatibility and easy adoption. Additionally, it is autoclavable for reusable endoscope sterilization.
Find out more at www.ovt.com.
Applications
- medical endoscopes
- medical and dental equipment
- catheters
- robotic surgery
- guidewires
Technical Specifications
-
active array size: 400 x 400
-
frame rate:
- 160 Kpixel (400 x 400): 30 fps
-
power supply:
- analog: 3.3V ±5%
-
power requirements:
25 mW (with I/O consumption) -
temperature range:
- operating: -20°C to +70°C junction temperature
- stable: 0°C to +50°C junction temperature
-
output formats: analog signal output
-
optical size: 1/31″
-
lens chief ray angle: supports lenses up to 15° CRA
-
scan mode: progressive
-
color mosaic: RGB Bayer pattern
-
pixel size: 1.008 µm x 1.008 µm
-
image area: 411.264 µm x 411.264 µm
-
package dimensions: 550 µm x 550 µm
Functional Block Diagram
Product Features
- optical size of 1/31″
- AntLinx™ Analog output
- single 3.3V power supply
- on-chip PLL
- serial peripheral interface (SPI)
- exposure and gain control
- pseudo-global shutter (LED mode)
- PureCel®Plus-S pixel structure
- improved sensitivity, FWC, zero blooming, low noise, and low power consumption
- enhanced NIR sensitivity
- square aspect ratio
- minimum package size (total 4 pads)
- autoclavable
- 4 m drive distance
4275 Burton Drive Santa Clara, CA 95054 USA.
Tel: + 1 408 567 3000
Fax: + 1 408 567 3001 www.ovt.com.
OMNIVISION reserves the right to make changes to its products or to discontinue any product or service without further notice. OMNIVISION and the OMNIVISION logo are trademarks or registered trademarks of OmniVision Technologies, Inc. PureCel and OVMed are registered trademarks of OmniVision Technologies, Inc. AntLinx is a trademark of OmniVision Technologies, Inc. All other trademarks are the property of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>