SRIAXNOL PJ132 Home Theater Projector Instruction Manual

PJ132 Home Theater Projector

Home Theater Projector
INSTRUCTION MANUAL MODEL NO.: PJ132
Email: support@SRIAXNOL.com PLEASE READ BEFORE OPERATING THIS EQUIPMENT

Important Safety Instructions
1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifier) that product heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus. 10. Only use attachments/accessories specified by the manufacturer. 11. Unplug this apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
1

Additional Warnings and Precautions
1. Do not look directly into the projector light. 2. Don’t touch the project lens. 3. Mains adapter is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. 7. WARNING: Shock hazard – Do Not Open. 8. Caution and marking information is located at the rear or bottom of the apparatus. 9. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing. 10. Objects filled with liquids, such as vases, shall not be placed on the apparatus.
2

FCC Warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
In The Box

Cleaning Cloth

AC Power Adapter

Lens Cover

Remote

Main Unit
HDMI Cable
3

Home Theater Projector INSTRUCTION MANUAL MODEL NO.: PJ132
Email: support@SRIAXNOL.com PLEASE READ BEFORE OPERATING THIS EQUIPMENT
User Manual

Table of Contents
Important Safety Instructions – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P1 Additional Warnings and Precautions – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P2 FCC Warning – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P3 In The Box – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P3 Table of Contents – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P4 Remove & Close The Lens Cover – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P5 Placing of Your Projector – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P5 To reduce Image Distortion – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P6 Distance Between The Projector And Screen – – – – – – – – – – – – – – – – – – – – – – – – P6 Installing Your Projector in the Ceiling – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P6 Adjust The Vertical Location – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P7 Adjust The Focus And Keystone – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P7 Controls of Remote – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P8 Install / Remove Batteries of Remote – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P8 Controls of Projector – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P9 Install Power Adapter – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P10 Main Button Operation – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P10 Connect HDMI Show The Image On Projector Screen – – – – – – – – – – – – – – – – – P11 Connect AV Show The Image On Projector Screen – – – – – – – – – – – – – – – – – – – P11 Connect VGA Show The Image On Projector Screen – – – – – – – – – – – – – – – – – P12 Connect Audio Output (Aux Out / Line Out / Earphones) – – – – – – – – – – – – – – P13 Install USB Device And TF (Micro SD) Card – – – – – – – – – – – – – – – – – – – – – – – – P13 Using TF Card And USB Playback (Media Player) – – – – – – – – – – – – – – – – – – – – P14 Using Bluetooth Playback – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P15 Multi-screen interactive connection for phone and projector – – – – – – – – – – – P16 WiFi Connection – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P16 Screen Mirroring for Android System (With WiFi) – – – – – – – – – – – – – – – – – – – – P16 Screen Mirroring for Android System (Without WiFi) – – – – – – – – – – – – – – – – – P16 Screen Mirroring for iOS System (With WiFi) – – – – – – – – – – – – – – – – – – – – – – – P17 Screen Mirroring for iOS System (Without WiFi) – – – – – – – – – – – – – – – – – – – – – P17 WiFi Setting Menu – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P17 Using Projector Menu 1 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P18 Using Projector Menu 2 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P18 Using Projector Menu 3 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P19
4

Remove & Close The Lens Cover

Remove the lens cover before using

LENS COVER

REMOVE

Close the lens cover when unit is not using

LENS COVER

CLOSE

Placing of Your Projector

Your projector can be installed in four different configurations (see picture below):

Front Table

Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

Rear Table

Rear Table: Select this location with the projector placed near the floor behind the screen. NOTE: That a special rear projection screen is required.

Front Ceiling

Front Ceiling: Select this location with the projector suspended upside-down from the ceiling in front of the screen. NOTE: A projector mount is required to install the projector in a ceiling.

Rear Ceiling

Rear Ceiling: Select this location with the projector suspended upside-down from the ceiling behind the screen. NOTE: A projector mount is required to install the projector in a ceiling. A special rear projection screen is required.

5

To reduce Image Distortion
· Move the projector as close to the center of the screen as possible.
· The light beam from the projector should be perpendicular to the screen for a rectangular or square image.

Distance Between The Projector And Screen

Measure the distance between the projector and where you want to position the screen. This is the projection distance.

DISTANCE

SCREEN SIZE

Distance 1.16m 1.35m 1.51m 1.79m 2.15m 2.81m 3.43m 4.44m

Screen Size 36 inch 45 inch 50 inch 60 inch 72 inch 100 inch 120 inch 150 inch

Installing Your Projector in the Ceiling

When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount. Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial. NOTE: Projector mount and screw(s) not included.

CEILING

HANGER

FIXED HANGER HOLE (6mm diameter)

6

Adjust The Vertical Location
Follow below picture to adjust the vertical location.

SCREEN
VERTICAL DIMENSION

PROJECTOR

SCREEN
VERTICAL DIMENSION

PROJECTOR

SCREEN VERTICAL DIMENSION
Adjust this knob ( ANGLE ADJ. knob) to fine- tune the display angle to higher.

PROJECTOR

Adjust The Focus And Keystone
Follow below picture to adjust the focus and trapezoidal screen.
Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center.
Keystone image is created when the projector lens is projected from above or below the center of the screen. Keystone correction restores the distorted image to a rectangular or square shape.
KEYSTONE ADJ. KNOB

FOCUS ADJ. KNOB Then sharpen the image by rotating focus knob.
7

Controls of Remote
Power ON/OFF Skip Next / Previous File
Enter to Menu Source Selector Decrease Volume Sound

Mute Audio Sound Play / Pause
Navigator Exit the Menu Increase Volume Sound

Install / Remove Batteries of Remote
Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover.
NOTES: · Batteries shall not be exposed to excessive heat such
as placing under the sunlight or near a fire. · Please make sure the batteries are installed with their
correct polarities. · Do not mix old and new batteries. · Use only the same type of batteries. · Do not dispose of the batteries in fire, battery may
explode or leak. · Do not recharge a non-rechargeable battery.
8

BATTERY DOOR

Controls of Projector
1 Front View

3

4

Rear View

2
Top View

5

Right Side View

6

161718 19 20 21

7

8 9 10 1112 13 14 15

1 LENS

2 ANGEL ADJ. Knob

3 VGA IN Port

4 IR Sensor (Rear)

5 SPEAKER

6 FOCUS ADJ. Knob

7 TRAPEZODAL ADJ. Knob

8 SOURCE Buttonn

9

Vol- Vol+ Button

10 RETURN Button

11 OK Button

12

Button

13 POWER Button

14 POWER Indicator

15 MENU Button

16 TF Card Slot

17 Audio Out Jack

18 AV IN Jack

19 HDMI 1 & 2 Ports

20 USB Port

21 DC IN Jack

9

Install Power Adapter
Follow below picture to connect power adapter. 1. Insert the DC plug of the adaptor into the DC IN JACK on the side of the unit. 2. Plug the AC power cord of small plug side to AC input socket of adaptor. 3. Plug the AC power cord of AC plug side into the 120V AC outlet. WARNING: Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus.
Main Button Operation
– Press the button to switch on unit, press again to turn off. / SOURCE – Press the button to select input source. / MENU – Press the button to enter projector menu.
– Press the buttons to navigate and select screen item of menu. – Press the button to return to previous status or exit the menu. / – Press the buttons to select the sound level on the remote. Vol- / Vol+ – Press the buttons to select the sound level on the panel. – Press to mute the audio. Press again to resume.
– Press the buttons to search next or previous file on USB / TF. – Press the button to play/pause the playback of file on USB / TF card.
10

Connect HDMI Show The Image On Projector Screen

Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player

to the HDMI input.

1. Turn off the unit before connect HDMI cable.

2. After connection, press the button to turn on unit and power indicator will light GREEN.

3. In home screen, use

buttons to select HDMI 1 or HDMI 2 icon and press the OK

button to enter. If not in home screen, press the / SOURCE button to enter.

4. The video from the connected device will be shown on projector screen.

5. Press the button to turn off unit power.

HDMI CABLE

CABLE INCLUDED

Video Player

Important Note: If there is no sound from the internal speakers when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player’s digital audio settings and make sure it is set to “PCM Stereo” mode.
Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on.
Connect AV Show The Image On Projector Screen

Follow below picture to connect AV cable and device.

1. Turn off the unit before connect AV cable.

2. Use AV cable to connect follow below figure.

3. After connect, press the button to turn on unit and power indicator will light GREEN

4. In home screen, use

buttons to select AV icon and press the OK button to

enter. If not in home screen, press the / SOURCE button to enter.

5. The video of AV device will show on projector screen.

6. Press the button to turn off unit power.

VIDEO CABLE

LEFT CHANNEL RIGHT CHANNEL

Video signal cable : Yellow The left channel signal lines: White The right channel signal lines: Red
Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on.
11

Connect VGA Show The Image On Projector Screen
Follow below picture to connect VGA cable and device.

NOTE BOOK

COMPUTER CABLE

To VGA PORT
OR COMPUTER CABLE

DECK TOP

1. Turn off the unit before connect VGA cable.

2. Press the button to turn off power of your projector before connection.

3. After connect, press the button to turn on unit and power indicator will light GREEN

4. In home screen, use

buttons to select VGA icon and press the OK button to

enter. If not in home screen, press the / SOURCE button to enter.

5. The video of VGA device will show on projector screen.

6. Press the button to turn off unit power.

Please refer to the following table to adjust the output signal from computer

Type

Resolution

Line Frequency (KHz)

Field Frequency (Hz)

31.5

60

VGA

640×480

34.7 37.9

70 72

37.5

75

31.4

50

35.1

56

PC

SVGA

800×600

37.9 46.6

60 70

48.1

72

46.9

75

40.3

50

XGA

1024×768

48.4

60

56.5

70

SXGA

1280×1024 63.9

60

79.9

75

NOTE:

1. VGA connections do not support audio. You will need to use the laptop or computer’s connected speakers.
2. If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on.

12

Connect Audio Output (Aux Out/Line Out/Earphones)
Follow below picture to connect audio cable and device. 1. Press the button to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4. After using, turn off both unit.
AUDIO CABLE
Important Note: If there is no sound from the stereo audio output when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player’s digital audio settings and make sure it is set to “PCM Stereo” mode. Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on.
Install USB Device And TF (Micro SD) Card
Follow below picture to install USB and TF card. Turn off the unit before install USB / TF card.
USB TF
Note: This USB port is only used to read USB flash disk. DO NOT use it to charge any external equipment.
13

TF

Using TF Card And USB Playback (Media Player)

Install USB / TF device:

1. Turn off the unit before install USB / TF card.

2. Install the USB device into USB port / Install the TF device into TF slot.

3. After install, press the button to turn on unit and the power indicator light GREEN.

4. In home screen, use

buttons to select MOVIE / PHOTO / MUSIC / TEXT

icon and press the OK button to enter. If not in home screen, press the / SOURCE

button to enter.

5. If necessary, use the

button to select C or D and press OK button to enter.

6. Use

buttons to search the correct file to preview and press the OK button to

playback file.

7. Press

button to search next or previous file.

8. During playback, press the button to pause and press again to resume.

9. Press the / EXIT button to exit.

NOTE: Before remove USB / TF device, press the button to turn off power FIRST.

Sub-Menu on Movie screen

1. When movie playback, press the OK

button and more function screen show

on lower (figure 1).

2. Use the

button to select icon

and press the OK button to play

special function.

Figure 1.
Pause FB FF Prev N ext Stop Repeat All Set A Playlist Info Slow Step GotoTime Zoom In Zoom Out Aspect

Sub-Menu on Music screen

1. When music playback, press the OK

Figure 2.

button and more function screen show

on lower (figure 2).

2. Use the

button to select icon

Pause FB FF Prev N ext

and press the OK button to play special function.

Playlist Info GotoTime

Stop Repeat All M ute

Sub-Menu on Photo screen

1. When photo playback, press the OK

Figure 3.

button and more function screen show

on lower (figure 3).

2. Use the

button to select icon

and press the OK button to play

special function.

Pause Prev N ext Stop Repeat All M usic Off Playlist Info

90

90

Rotate Rotate Zoom In Zoom Out M ove M usic S…

Sub-Menu on Text screen

1. When text playback, press the OK

button and more function screen show

on lower (figure 4).

2. Use the

button to select icon

and press the OK button to play

special function.

Figure 4.
Previous… Next Page Prev N ext Stop M usic Off Playlist Info M usic S…

Note: If hot plug cause the unit hang up or malfunction, reset the unit by unplug the DC IN power jack at the rear right side of the unit. Wait for 10 seconds before reconnecting the power and turning the unit back on.

14

Using Bluetooth Playback

Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices.

Bluetooth Connection

1. Turn on your External Bluetooth Speaker and select to Bluetooth pairing mode.

Note: The effective distance between your external device and projector is within 10

meters (30 feet).

2. Press the button to turn on unit.

3. Press the / MENU button to enter the projector menu screen.

4. Use the

button to select Sound menu.

5. Use the

button to select BT Setting column as figure 1.

6. Press the OK button to enter BT Setting menu and use

buttons to select On. (If BT Setting is On, press the OK button to

Sound Mode Standard

Treble

50

Bass

50

Balance 0

BT Setting Off

Figure 1

enter BT Setting menu.) 7. Unit will try to reconnect the previous Bluetooth device, if it is
connected before. If not, select Search BT and press OK button to search device. 8. Wait a while, the available Bluetooth speaker device name will

BT Setting Off
Disconnect / Search BT XXXXXX YYYYYY ZZZZZZ

show in a list as figure 2. (For example: XXXXXX, YYYYYY, ZZZZZZ and etc.)

Figure 2

9. Use the

buttons to select your desired Bluetooth speaker device and press OK

button to connect. (Make sure your Bluetooth headset/audio is connecting)

10. A few seconds, an indicator sound will be heard that your projector and external

Bluetooth speaker connected. At the same time, there is “C:XXXXXX” to indicate the

connected device on the BT Setting menu. Then press button to exit.

11. After connection completed, you can listen to music by your Bluetooth receiver device

such as a headphone or speaker wirelessly.

12. If you want to change to pair with another Bluetooth Enabled Device, please repeat

above step 3 to step 10.

Notes:

1. After connecting, Bluetooth device’s name will be stored and will automatically connect

for next time.

2. Projector Bluetooth (Transmitter) function can only pair with Bluetooth receiver such as

headphone or speaker for music streaming wirelessly. Use your Bluetooth device volume

control if necessary.

Disconnect the Bluetooth

1. Press the / MENU button to enter the menu screen.

2. Use the

buttons to select Sound menu.

3. Use the

buttons to select BT Setting and press OK button to enter BT Setting menu.

4. Use the

buttons to select Off and press the OK button to disconnect the Bluetooth

function. Then press button to exit.

15

Multi-screen interactive connection for phone and projector

WiFi Connection

In home screen, use

buttons to select MIRACAST icon and press OK button to

enter. If not in home screen, press the / SOURCE button to enter.

1. In “Waiting for connection…” page, press OK button to enter WiFi setting menu.

2. In WIFI Setting menu, select WiFi and press OK button, unit will

search available WiFi and show on the screen.

3. Choose the available local WiFi router and input password to

connect (using

buttons to input password).

4. If unit success to connect the WiFi, it will show the ” 3 ” behind

the desired local WiFi name on the screen.

5. Press button twice to return “Waiting for connection…” page for iOS/Android screen

mirroring.

6. If you want to connect another WiFi, repeat above step #1-3.

Note: When the router is successfully connected, the projector will automatically

connect to the router next time.

Screen Mirroring for Android System (With WiFi) Follow above WIFI Connection section. Then connect your Android mobile device to the same WiFi router. Airplay Function: 1. Play the video on the video app on the mobile, click Projection Screen ” ” icon and
select “PROJECTOR-XXXXXX-DMR” on the mobile settings. 2. After connected, the video / movie will be projected on the projector screen. Screen Mirroring: 1. Swipe down from the top of your mobile, click Multi-Screen ” ” icon and select
“PROJECTOR-XXXXXX” on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen.

Screen Mirroring for Android System (Without WiFi) Make sure the projector disconnect to any WiFi. If connected before, press OK button to enter WIFI Setting menu to select connected WiFi to forget WiFi and return to waiting for connection… page. Screen Mirroring: 1. Swipe down from the top of your mobile, Click Multi-Screen ” ” and select
“PROJECTOR-XXXXXX” on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen. Note: 1. Without WiFi connection, only support screen mirroring function. Please connect WiFi if
you want to airplay. WiFi connection method please see WiFi connection section on previous page. 2. Different mobile models with different names of screen mirroring function, for examples: Multi-screen, Wireless Display, Screen Mirroring, Smart View etc… 3. XXXXXX is the projector device no. which show on the upper left corner of the “Waiting for connection…” page.
16

Screen Mirroring for iOS System (With WiFi) Follow above WIFI Connection section. Then connect your iOS mobile device to the same WiFi router. Airplay Function: 1. Play the video on the video app on the mobile, click Projection Screen ” ” icon and
select “PROJECTOR-XXXXXX-DMR” on the mobile settings. 2. After connected, the video / movie will be projected on the projector screen. Screen Mirroring: 1. Swipe up from the bottom of your mobile, click Screen Mirror ” ” icon and select
“PROJECTOR-XXXXXX” on the mobile settings. 2. After connected, the mobile device contents will mirror on the projector screen.

Screen Mirroring for iOS System (Without WiFi) Make sure the projector disconnect to any WiFi. If connected before, press OK button to enter WIFI Setting menu to select connected WiFi to forget WiFi and return to waiting for connection… page. Screen Mirroring: 1. Turn on WiFi on your iOS device, click “PROJECTOR-XXXXXX” and input the password
12345678 to connect. 2. Swipe up from bottom of your mobile, click Screen Mirror ” ” icon and select
“PROJECTOR-XXXXXX” on the mobile settings. 3. After connected, the mobile device contents will mirror on the projector screen. Note: 1. Without WiFi connection, only support screen mirroring function. Please connect WiFi if
you want to airplay. WiFi connection method please see WiFi connection section on previous page. 2. XXXXXX is the projector device no. which show on the upper left corner of the “Waiting for connection…” page.

iOS Data Cable Screen Mirroring: Select the MIRACAST function in the main interface, connect your iOS device directly to the projector using the USB cable, click “Trust” in the pop-up box on your phone screen to complete the screen mirroring

WiFi Setting Menu

In home screen, use

buttons to select MIRACAST icon and press OK button to

enter “Waiting for connection…” page. Then press OK button to enter WIFI Setting menu.

Use UP button or DOWN button to move

through and select desired WiFi, Mirror Setting,

OTA and Reset.

1. WiFi

Select desired local WiFi router to connect.

2. Mirror Setting

Select Airplay or Screen Mirroring.

3. OTA

Select it for Screen Mirroring software

update.

4. Reset

Reset the Screen Mirroring and restore all

of the default settings.

17

Using Projector Menu 1

Press /MENU button to enter projector menu. Press

buttons to select PICTURE menu.

Picture Mode Contrast Brightness
Color Sharpness
Color Temperature Noise Reduction

Standard 50 50
50 50
Medium Middle

This Picture menu showed on right upper of view screen.

USE

TO SELECT

Picture Mode Standard PRESS OK

USE

TO SELECT

Use

to select different picture effect to Standard / Dynamic /

Mild / User. Use

to selectand

to adjustContrast/

Brightness/ Color / Sharpnessdigit If choseUser item.

Contrast 50

USE

TO SELECT

PRESS OK

Use

button toadjust Contrast level 0 to 100. (Active in User

item of Picture Mode).

Brightness 50

PRESS OK Use

button toadjust Brightness level 0 to 100. (Active in User

USE

TO SELECT

item of Picture Mode).

Color 50

USE USE

TO SELECT

PRESS OK

Sharpness 50

UUSSEE

TO SELECT

PRESS OK

Color Temperature Medium PRESS OK

USE USE

TO SELECT

Use

button toadjust Color level 0 to 100.(Active in User item

of Picture Mode).

Use

button toadjust Sharpness level 0 to 100. (Active in User

item of Picture Mode).

Use

button to select different color temperature to Cool /

Medium / Warm.

Noise Reduction Middle PRESS OK Use

button to select Off / Low / Middle / High .

Using Projector Menu 2

Press /MENU button to enter projector menu, press

buttons to select SOUND menu.

Sound Mode Treble Bass Balance
BT Setting

Standard 50 50 0
Off

This Sound menu showed on right upper of view screen.

USE

TO SELECT

Sound Mode Standard PRESS OK

USE

TO SELECT

Treble 50

PRESS OK

USE

TO SELECT

Bass 50

PRESS OK

USE

TO SELECT

Balance 0

PRESS OK

USE

TO SELECT

Use

button to select different sound effect Standard / Movie /

Music / Sports / User. Use

to select and

to adjust

Treble and Bass digit if chose User item.

Use

button to select Treble level 0 to 100.

(Active in User item of Sound Mode).

Use

button to select Bass level 0 to 100.

(Active in User item of Sound Mode).

Use

button to select Balance level to -50 to +50.

BT Setting Off PRESS OK Use

button to select BT On / Off.
18

Using Projector Menu 3

Press /MENU button to enter projector menu, press menu.

buttons to select OPTION

OSD Language

English

Flip

Front Table

Aspect Ratio

16:9

Restore Factory Default

Software Update (USB)

This OPTION menu showed on right upper of view screen.

USE

TO SELECT

OSD Language English PRESS OK

USE

TO SELECT

FlipOKFront Table

USE

TO SELECT

PRESt S OK

Aspect Ratio 16:9

USE

TO SELECT

PRESS OK

Use

button to select different language.

To select different project direction Front Table / Front Ceiling / Rear Table / Rear Ceiling.

Use

button to select different Aspect Ratio 4:3 / 16:9 / Full

Follow below figure.

Restore Factory Default PRESt S OK Use

button to select Y or N. If choose “Y” that your unit will

USE

TO SELECT

go to factory default setting.

Software Update (USB) PRESt S OK For service center use only.

Aspect Ratio AV mode HDMI mode VGA mode USB / TF input (movie mode)

4:3, 16:9, Full, Panorama 4:3, 16:9, Full, Panorama, Just Scan 4:3, 16:9, Full 4:3, 16:9, Full, Panorama, Just Scan

DISCLAIMER Unless specifically agreed to in writing, SRIAXNOL: A. SRIAXNOL makes no warranty as to the accuracy, suffciency or suitability of any technical
or other information provided in its manuals or other documentation. B. SRIAXNOL assumes no responsibility or liability for loss or damage, whether direct,
indirect, consequential or incidental, which might arise out of the use of such information. The use of any such information will be entirely at the user’s risk.

19

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>