MODENA BP 3435 Built-in Water Dispenser User Manual

MODENA BP 3435 Built-in Water Dispenser

This guidebook explains everything you need to know about your new product. Please contact our Customer Care should you need further assistance through www.modena.com.

SAFETY WARNINGS

• Read all instructions before using the water dispenser.
• Never clean parts with flammable fluids.
• Do not store or use any other flammable vapors and liquids in the vicinity of this or any other water dispenser.
• During operation keep it beyond the children to avoid scald..
• Never turn on the heating switch when there is no water.
• Adopt the ground wire to avoid any electric shock.
• This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person
• responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged,it must be replaced by the manufacturer.

NAME OF PARTS

1. Control panel
2. Cold water tap
3. Hot water tap
4. Water tray cover
5. Water tray
6. Water Purifier inlet
7. Bottled water inlet
8. Pump – Selenoid switch

INSTALLATION

Installation Notes

• Before installation, the user should decide the water source to use the right inlet according to the source.
• The dispenser should be installed in a flat, easily accessible, and secure place (not tilted).
• Do not install the dispenser and power outlet in a damp or wet area. Make sure the power outlet is grounded properly.
• It is recommended to add a power switch in front of the dispenser, to cut off the electric current easily.
• This appliance is compatible to connect with bottled water (gallon) and water purified tap water.
• Make sure that the PE hose is not bent to avoid blocking the water flow.
• If the dispenser is installed on a cabinet, make sure that the space in the cabinet has enough room for heat dissipation to avoid machine dysfunction. Install the appliance according to this instruction:

Installation Method

Set the cabinet position, the space should fit the dispenser according to the specified size requirements.

Product size

Connecting the PE Hose to the Water Dispenser

Prepare the PE hose, cut it flat at both ends. Separate the fastener from the blue quick connector.

Insert the PE hose into the fastener ring up until the very end part. To see if it’s secured, pull it using the same strength. If the hose does not move, then it is set and will not fall off.

Insert the fastener into the space between the connector and hook ring to secure the connection.

The dispenser is equipped with PE hose that requires a hole to insert the hose through the back side of the cabinet.If the dispenser is installed on a cabinet, it has to be secured.

Dispenser equipment must be set on the back of the cabinet, detach the water tray and mark the position with the bolt on the bottom of the Dispenser, as shown in the picture:

Connecting Bottled Water and Dispenser

• Connect the PE hose to the pipe for the gallon, the connection method is the same as the install hose method (no. 2)
• Insert the pipe to the gallon and then plug the cover to the mouth of the gallon.
• Insert the gallon and close the lower cabinet door.

If the water source is from the water purifier, pull out the PE hose from the pipe for a gallon, then connect the PE hose to the clean water outlet of the water purifier.

HOW TO USE

Control Panel

Remark:

1. Water capacity button
2. Hot water setting button
3. Hot water tap button
4. Display screen
5. Cold water tap button
6. Light button
7. Cooling system button

Getting Started

1. Setting the amount of water
   Touch the button once to set the water capacity of 150ml, twice for 250ml, and thrice to set continuous water flow.

2. Hot water temperature setting
   Touch the button once to set the hot water temperature, there are 3 options: 55°C, 85°C and 100°C. If you need room temperature water, set the temperature to _°C.

3. To dispense hot water
   Touch the button once to dispense hot water, the hot water will flow out according to the amount chosen in step 1. If the amount is set as continuous flow, water will stop flowing once the finger is lifted from the button.

4. To dispense cold water
   Touch the button once to dispense cold water, the cold water will flow out according to the amount chosen in step 1. If the amount is set as continuous flow, water will stop flowing once the finger is lifted from the button.

5. Switching the light on
   Touch the button once to switch on the light, and then touch it once again to switch off the light.

6. Switching the compressor/Cooling system on
   Touch the button once to switch on the compressor, and then touch it once again to switch off the compressor.

7. Child lock activation
   Hold the button 3 seconds to activate and deactivate the Child Lock

MAINTENANCE

NOTE:
To keep the optimum function of the machine for an extended time, pay attention to maintenance. The power plug should be removed from the power socket before starting the maintenance process.

• Do not pull the cable to remove the plug from the power socket. Pull the plug head instead.
• This dispenser has been disinfected before shipping.
• Clean the hose, water tank, and heating element at least once a year with an expert. This procedure will keep the machine in its best condition and prolong its life. Do not disassemble the machine by yourself to avoid damage to the machine.
• Use a soft damp cloth to clean the dispenser surface, and use a soft dry cloth to dry the surface. Do not let water get into the machine.
• Make sure the power cord is unplugged from the power source when discarding excess water, during the maintenance process, or when the appliance is not used for a long time. Meanwhile, when the hot is not heated, open the drain valve until there is no water in the appliance. Meanwhile, if the hot water tap releases cold water, let the valve open until there is no water left inside the dispenser.
• If the display screen shows an empty water icon, that means that the water has run out. Change the water gallon with the new one immediately.
• In order to ensure the long-term normal use of the water dispenser, please check the function regularly. When an abnormality occurs, please notify the MODENA Call Center.

TROUBLESHOOTING

If abnormalities happen when in use, please stop using the appliance and unplug the power cord, and check the following table to make sure of the appliance’s condition. If necessary, please contact Modena Call Center.

Water is not hot or not cold

| •  Excessive dispensation of hot water or cold water ina short period of time.

•  Unit is not yet connected to electricity.

| •  Wait until the water becomes cold or hot.

•  Connect the cord to the outlet and press the heater and cooler switches.

Water is not being dispensed out of the tap| •  Water gallon is empty. The pipe is stuck or block something.| •  Replace the water gallon with a new one.

•  Turn off the switch cooling to 4

hours, then turn the switch back.

Leak on the water gallon support| Water gallon is leaking/ damaged| •  Replace water gallon with a new one, make sure the power cord is unplugged.
Loud noise| Improper installation or| Install unit on even and stable
Problem| Possible Cause| Recommended Action
---|---|---
during operation| placement of unit| surface
Error code – Err1| Hot temperature sensor is broken| Contact Modena service center
Error code –

Err2

| Internal leakage| Contact Modena service center

PRECAUTION

• If the appliance is not going to be used for a long period of time, unplug it and drain all water in its interior
• Wash and disinfect the system every 3-6 months with a suitable cleaner and according to its instructions for use
• Do not pull out the cable to unplug it. Do not turn the on and o- appliance by connecting it and disconnecting it from the source of electricity
• If you are not using the appliance for a long period of time or during the night, you can turn it o- to save energy
• The equipment must be installed keeping easy access to the electrical plug.

SPECIFICATION

Cold water output(liter/

hour)

| 2| 2
Hot water tank capacity

(liter)

| without water tank

(instant)

| without water tank

(instant)

Cold water tank capacity (liter)| 1.1| 1.1
Hot temperature (Celsius)| 55,85,100| 55,85,100
Cold temperature (Celsius)| ≤14| ≤14
Free-CFC compressor| Yes| Yes
Water tank material| Stainless Steel| Stainless Steel
Heating power (watt)| 2100| 2100
Compressor power (watt)| 120| 120
Voltage / Frequency| 220 V ~ / 50 Hz| 220 V ~ / 50 Hz
Product dimension| 595x560x455| 595x560x455
Cut-out dimension| 560x550x450| 560x550x450

Specifications of this appliance may change without notice to improve the quality of the product. Pictures in this manual are schematic and may not match your product exactly. Values stated on the machine labels or in the documentation accompanying it are obtained in the laboratory in accordance with the relevant standards. Depending on the operational and environmental conditions of the appliance, values may vary.

PT MODENA INDONESIA
Jl. Industri Raya I Blok D-8, Jatiuwung, Tangerang 15135.
www.modena.com.

References

• MODENA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>