Luminosa LT1042 7 Inch 1 Light Brushed Nickel Flush Mount User Guide
- June 8, 2024
- LUMINOSA
Table of Contents
Luminosa LT1042 7 Inch 1 Light Brushed Nickel Flush Mount
Safety Information
- WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire or other injuries which could be hazardous or even fatal.
- WARNING: Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn the circuit off.
- NOTICE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Warranty
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of two (2) years from date of purchase.
This warranty applies only to the original consumer and only to products used
in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the
product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on
any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear. The manufacturer does not warrant and
specifically disclaims any warranty, whether express or implied, of fitness
for a particular purpose, other than the warranty contained herein. The
manufacturer specifically disclaims any liability and shall not be liable for
any consequential or incidental loss or damage, including but not limited to
any labor/expense costs involved in the replacement or repair of said product.
Pre-Installation
PLANNING INSTALLATION
Read all instructions before assembly. Before starting installation of this
fixture or removal of a previous fixture, disconnect the power by turning off
the circuit breaker or by removing the fuse from the fuse box. To avoid
damaging this product, assemble it on a soft, non-abrasive surface such as
carpet or cardboard.
NOTE: Keep your receipt and these instructions for proof of purchase.
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Mounting Strap | 1 |
| BB | Mounting Screw (25 mm) | 2 |
| CC | Outlet Box Screw (15 mm) | 2 |
| DD | Ground Screw | 1 |
| EE | Wire Connector | 3 |
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| A | Canopy | 1 |
| B | Socket | 1 |
| C | Lock Nut | 2 |
| D | Globe | 1 |
| E | Socket Ring | 1 |
Installation
Ataching the mounting strap to the outlet box
- Screw the mounting screws (BB) into the outside holes of the mounting strap (AA).
- Mount the mounting strap (AA) to the outlet box (sold separately) using the outlet box screws (CC).
- Make sure the threads of the mounting screws (BB) are facing out when the mounting strap (AA) is attached to the outlet box.
Making the electrical connections
- Wrap the middle of ground wire from the fixture around the ground screw (DD) on the mounting plate (AA). Use a wire connector (EE) to connect the ground wire from the fixture to the ground wire from the outlet box.
- Use a wire connector (EE) to connect the white wire from the fixture to the white wire (neutral) from the outlet box.
- Use a wire connector (EE) to connect the black wire from the fixture to the black wire (live wire) from the outlet box.
- Wrap the three wire connections with electrical tape for a more secure connection.
- Position the wires back inside the outlet box.
Securing the canopy
- Place the canopy (A) over the outlet box.
- Align the mounting screws (BB) so they protrude through the appropriate holes on the canopy (A).
- Screw the lock nuts (C) onto the mounting screws (BB) to secure the canopy (A).
Attaching the globe
- Place the globe (D) over the socket (B) .
- Screw the socket rings (E) onto the sockets (B) to secure the globe (E).
Installing a bulb
- Screw a 60-Watt maximum, incandescent medium-base bulb (sold separately) into the socket (B).
NOTE: You can use a LED equivalent energy-saving bulb that does not exceed 8 Watts (sold separately).
Care and Cleaning
- Clean the fixture with a soft, dry cloth.
- Do not use any cleaners with chemicals, solvents or hash abrasives.
WARNING: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box.
Troubleshooting
Troubleshooting|
---|---
| Problem| Possible Cause| Solution
The fixture will not illuminate.| The power is off.| Ensure the power supply
is On.
The circuit breaker is off.| Ensure the circuit breaker is in the On position.
The fuse blows or circuit breaker trips when the fixture is illuminated.| The
wires are crossed or the power wire is grounding out.| Check the wire
connections.
Questions, problems, missing parts?
Please consult your local Home Depot store or email Customer Service at
BrightCustomerService@gmail.com Retain this
manual for future use.