NEVERLEAK 2518000 Aluminum 200-ft Cart Hose Reel Instruction Manual
- June 8, 2024
- NEVERLEAK
Table of Contents
NEVERLEAK 2518000 Aluminum 200-ft Cart Hose Reel Instruction Manual
Product Overview
| ITEM | DESCRIPTION |
|---|---|
| 1 | Hose Reel Chassis |
| 2 | Grip Handle |
| 3 | Grip Handle Screw x2 |
| 4 | Crank Handle |
| 5 | Crank Handle Screw |
| 6 | Leader Hose |
| 7 | Water System Inlet |
Before you begin…
Please read and follow instructions prior to use.
Phillips head screwdriver required for assembly.
The AMES Companies, Inc.® is not responsible for replacing parts amaged due
to incorrect use.
CAUTION
Turn off water at spigot and relieve pressure inside unit when not in use.
WARNING
This product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm. DO NOT place your hands
in your mouth after handling the product. DO NOT place the product in your
mouth. DO NOT drink water from the hose. WASH HANDS AFTER USE
For Warranty Policy information visit www.ames.com
INSTALLATION
UNPACK
Carefully remove all parts from the box and place on a smooth, flat surface.
Remove leader hose and set aside.
**ATTACH GRIP HANDLE
**
Align handle with the cart handle receptacles, carefully noting the handle bend orientation. Gently slide the handle evenly and horizontally into the cart receptacles until it clicks in to place on both sides. After the grip handle is in place, install the 2 grip handle screws through the frame and into the handle using a Phillips head screwdriver
TIP
The grip handle can be removed as needed for storage or transportation. To
remove the grip handle, remove the screws then gently lift the latches on both
sides and lift the handle out of the frame.
ATTACH CRANK HANDLE
Attach the crank handle to the right side of the cart as viewed from the
front. Attach using the screw provided and a Phillips head screwdriver.
ATTACH WATERING SYSTEM
The water system inlet can be positioned to face forward, backward, or
downward. To install, pull latch upward, insert water system inlet in desired
orientation making sure to push it all the way in, then lock by pushing latch
back down into place.
ATTACH LEADER HOSE
Make sure rubber hose washers are inside leader hose couplings. Attach
leader hose to water system on unit and other end of leader hose to spigot.
ATTACH GARDEN HOSE
Attach garden hose (not included) to water system on hose hub. Make sure
rubber hose washer is inside hose coupling.
HOSE WINDING INSTRUCTIONS
To wind hose, reel it in by turning crank in clockwise direction and
guiding hose evenly onto reel.
Remove foot protectors prior to use.
TIP
For better stability, use foot step at the bottom front of the cart frame
to hold hose reel in place when reeling hose in. DO NOT use tubing crossbar as
a step.
OPERATION
- Turn water on at spigot; remove desired length of hose from unit and use for watering.
- Bring nozzle (not included) end of garden hose back to unit, turn water off at spigot and squeeze nozzle for few seconds to relieve pressure in hose.
- To wind hose, reel it in by turning crank in clockwise direction and guiding hose evenly onto reel
STORAGE
- Turn water OFF at spigot and squeeze nozzle to relieve pressure inside unit when not in use.
- Drain water from unit to prevent damage from freezing
- Store unit in shaded place.
MAINTENANCE
-
Lubricate O-rings annually:
a. Pull water system latch upward.
b. Remove water system inlet.
c. Remove and grease the two O-rings with silicone grease and reassemble. -
Replace rubber washers on garden and leader hoses annually to prevent leaks.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>