iDP SMART-81 Laminator Installation Guide
- June 8, 2024
- idp
Table of Contents
SMART-81 Laminator
Installation Guide
Features
| 1. Air Vent | 5. IR Comm. Port |
|---|---|
| 2. Physical Lock | 6. Card Exit Slot |
| 3. Front Cover | 7. Power Switch |
| 4. Card Insert Slot | 8. AC Power Connetor |
Included
Laminator Installation
-
Open the front side of the Laminator cover.
-
Hold the Laminator film cartridge handle and pull it out.
-
Insert the Laminator film SUPPLY core on the mounting place of the cartridge core until it “clicks”. Wind the film around four shafts following the diagram arrow, and insert TAKE UP core into the core mounting until it “clicks”.
-
Adjust the tension of loaded Laminator film in the direction of the arrow using the TENSION KNOB on the front side of the film cartridge.
-
Mount the Laminator film cartridge. The cartridge should be firmly combined with the Laminator.
-
Close the front side of Laminator cover.
-
Connect the Printer and Laminator with binding clamps.
-
Connect the AC Power cable and USB cable.
-
Turn on the Printer by pressing the On/Off button at first and then, turn on the Laminator.
-
Install the Card stacker.
※ The Card stacker is included with the SMART-81 printer.
-
Check the model name displayed on the SMART-81 Printer LCD has been changed to SMART-81SL or SMART-81DL.
FCC Instructions
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Specifications
Model| | SMART-81 L
Deed Heating Lamination
---|---|---
Laminating| Laminating Type
Film| Film Type| pear. Holographic
Film Thickness| 0.6mi1, 1.0mil
Speed| Single sided Lamination| 20 secjcard (180 cards/hour)
System| Interface| 1 LED Indicator
Communication| –
Power Supply/ Consumption| Free Voltage (AC 100-240V. 50-60Hn/ 2.0A
Temperature/Humidity| 15-35t I35-70%
Dimensions| math (Millimeter / Inch)| 240 x 224 x260/ 9.5s 8.8 x 102
Hg/abs| 5.8/ 12.8
Option| Security| Physical Lock
IDP Corp., Ltd.
601, 50, Digital-ro 33-gil,
Guro-gu, Seoul, Korea,
08377
T+82-2-6099-3700
F +82-2-6099-3717
E sales@idp-corp.com| IDP Americas, Inc.
1485 S County Trail, Unit 306
East Greenwich, RI 02818
USA
T +1-401-400-7111
F +1-401-667-7445
E sales@idpamericas.com| IDP Middle East
13F, Jafza View 18, Downtown
Jebel Ali P.O.Box 17588,
Dubai U.A.E.
T +971-4-889-5900
E mea@idp-corp.com
---|---|---
© 2022 IDP Corp., Ltd. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>