CPDEVICE APOLLO 7 Pro Rugged Vehicle Mount Computer User Guide
- June 8, 2024
- CPDEVICE
Table of Contents
CPDEVICE APOLLO 7 Pro Rugged Vehicle Mount Computer
Model Appearances
Packages & Accessories
Please note that when you receive our products, you would receive two
packaging types, a large package and a small package. In addition to the
tablet, there is only a 4G antenna included as part of the standard
configuration (as shown in the picture).
There is one accessory included in the box. In the case of a product with
ordinary positioning accuracy, there will be another GNSS positioning antenna
enclosed in the box (as shown in the picture). All wiring, mounting brackets,
and other accessories are optional and should be purchased separately.
Installation Method
There are standard RAM bracket installation holes in the bottom shell of the
Apollo series products. RAM-101U is the recommended RAM model, and the RAM
bracket is installed as follow
If you wish to select or customize the bracket on your own, please refer to
the following installation dimension diagram:
Definitions of Connector Interface
| PORT1-12P | PIN Definition | PORT2-10P | PIN Definition |
|---|---|---|---|
| 1 | TX2 | 1 | CAN2-H |
| 2 | RX2 | 2 | CAN2-L |
| 3 | B- | 3 | GND |
| 4 | ACC+12V | 4 | CVBS+12V |
| 5 | B- | 5 | GND |
| 6 | TX1 | 6 | CVBS1 |
| 7 | RX1 | 7 | CVBS0 |
| 8 | 12VOUT1 | 8 | 12out |
| 9 | CAN1-H | 9 | RS485-A |
| 10 | CAN1-L | 10 | RS485-B |
| 11 | B+12V | ||
| 12 | B+12V |
Power On Method
All CP products are powered on and start up in the same manner. For taking
power, three signal lines are used: B+, B-, and ACC. During startup, connect
B+ and ACC to the positive stage of the power supply, and B- to the negative
stage. There is a wide-voltage input on the tablet of 9-36V, and a power
supply of at least 2A is recommended. Following is a diagram of the
recommended power supply. Using the above method of taking power is beneficial
in controlling the standby current of the entire machine, reducing the risk of
data loss caused by sudden power failure of the tablet, and reducing the risk
of the machine being burned out due to poor contact of the physical switch
during booting.
Connection of APOLLO to PC
The APOLLO series only support USB2.0, thus a USB2.0 cable will be required to
connect the PC and tablet The USB2.0 male-to-male debugging cable is
recommended
After selecting the correct cable, you should connect both ends to the USB
ports on your PC and tablet. For firmware programming or debugging, please
change the USB port of the tablet from host mode to debug mode first.
Modifications to the APOLLO series are made through the settings
Connectors & Cables
1.Port2
2.Port2
Product Specs
System
| Octa-core, 1.8GHz
2G RAM
16G ROM, Supports 256G TF Extension
Android 9.0
---|---
Communication
| 2.4GHz/5.8GHz WiFi, IEEE 802.11 b/g/n,
Supports WiFi Shared Hotspot
BT2.1 +EDR/3.0/4.l LE/4.2BLE
4G/LTE (Dual SIM Optional)
GNSS (GPS/BDS/GLONASS),
Optional Centi-meter Level GNSS
OEM Board,
Optional lnterial Navigation Module
Built-in MIC (Optional)
Built-in Speaker
Rugged Feature
| IP65
Vibration & Shock: MIL-STD-810
Road Vehicle Standard: 1SO16750
Humidity 95%, Non-condensing
Operation Temperature: -20°C “‘+70°C
Storage Temperature: -40°C “‘+85°C
Display
| 7”. 1024*600p, 7S0cd/m’
5-Points Capacitive Multi-touch Screen
1/0 Interface
| RS-232″‘2
RS-4851
CAN “2 (Supports J1939, CANopen, 1S01S765)
USB 2.01
720p*2 AHO Camera
12V DC OUT2
Ethernet’s (Optional)
Power Management
| 9-36V DC Input
Ignition Control
Mechanical Spec
| Dimension (WHD): 19412729 mm
Weight: 0.7 kg
Button
| Power Key l, Function Key*2
Connector Type
| Standard Industry Waterproof Connector
SMA Female Connector2 (GNSS&4G)
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.