Radio Thermostat Company of America

CT100 Plus

SKU: CT100

Quickstart

This is a ****

HVAC-Thermostat
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
From the CT100s Menu screen, touch MATE under the radio icon. The Network Include screen displays a large r1.Touch MATE again. This initiates the network inclusion process. The MATE icon and the status indicator LEDs will blink.When the CT100 has successfully included into a Z-Wave network, theMATE icon is replaced by the LINK icon under the radio tower.

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

The CT100 Plus is a sleek, modern thermostat design for home automation systems.Its clean user interface compliments app-enabled systems.It features adjustable real-time alerts to enable cloud triggers, a robust data stream of HVAC information for cloud monitoring, and configurable comfort response settings to customize home control scenes.The CT100 Plus is compatible with all popular HVAC systems and is battery-operated without the need for a C-wire.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Switch the thermostat to Off Mode.Press and hold the lower left corner of touch screen for five (5) seconds. The thermostat then resets itself, displays its current firmware version, and restarts in Off Mode.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

From the CT100s Menu screen, touch MATE under the radio icon. The Network Include screen displays a large r1.Touch MATE again. This initiates the network inclusion process. The MATE icon and the status indicator LEDs will blink.When the CT100 has successfully included into a Z-Wave network, theMATE icon is replaced by the LINK icon under the radio tower.

Exclusion

Same process as inclusion. Similarly, when you are trying to exclude from a network, the LINK icon disappears when the node has successfully excluded the network.

Communication to a Sleeping device (Wakeup)

This device is battery operated and turned into deep sleep state most of the time
to save battery life time. Communication with the device is limited. In order to
communicate with the device, a static controller C is needed in the network.
This controller will maintain a mailbox for the battery operated devices and store
commands that can not be received during deep sleep state. Without such a controller,
communication may become impossible and/or the battery life time is significantly
decreased.

This device will wakeup regularly and announce the wakeup
state by sending out a so called Wakeup Notification. The controller can then
empty the mailbox. Therefore, the device needs to be configured with the desired
wakeup interval and the node ID of the controller. If the device was included by
a static controller this controller will usually perform all necessary
configurations. The wakeup interval is a tradeoff between maximal battery
life time and the desired responses of the device. To wakeup the device please perform
the following action:

When included into a Z-Wave network on battery power, this device is a FLiRS device.The Thermostat will wake up for communication when it receives a valid Z-Wave beam.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Temperature Reporting Threshold

The Temperature Reporting Threshold Con!guration Set Command sets the reporting threshold for Reporting Threshold changes in the ambient temperature as detected by the thermostat.
Size: 1 Byte, Default Value: 2

SettingDescription

Parameter 10: Temperature Reporting Filter

The Temperature Reporting Filter configuration command sets upper and lower bounds of the ambient temperature reporting.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 12: Multicast

This parameter controls how the thermostat sends unsolicited reports.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 14: Save Energy Mode Type

This configuration value is used to read/white what behavior Save Energy Mode causes in the thermostat when the thermostat enters Save Energy Mode.
Size: 1 Byte, Default Value: 3

SettingDescription

1 – 255| 1=Adjust by target delta, 2=Least consuming point in the running program, 3=Save energy absolute setpoint, 255=Save Energy not supported (read- only value)
---|---

Parameter 2: HVAC Settings

The HVAC Settings Configuration Report Command returns the current HVAC con!guration. The HVAC settings must be !xed before the thermostat is joined to the Z-Wave network.
Size: 4 Byte, Default Value: 0

SettingDescription

0 – 2147483647| Byte 1: normal (1) or heat pump (2). Byte 2, Bits 7-4: Gas (1) or Electric (2). Byte 2, Bits 3-0: # of Auxiliary Stages. Byte 3: # of Heat Pump Stages. Byte 4: # of Cool Stages.
---|---

Parameter 3: Utility Lock

The Utility Lock Con!guration Set command enables or disables the utility lock. If the utility lock is enabled, the setpoint cannot be modi!ed directly via the thermostat screen.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 4: C-Wire/Battery

The C-Wire / Battery Status Con!guration Report Command returns the status of the thermostat power source. The power state is fixed when the thermostat joins the network.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 5: Humidity Reporting Threshold

The Humidity Threshold Con!guration Set Command sets the reporting threshold for changes in the relative humidity as detected by the thermostat.
Size: 1 Byte, Default Value: 5

SettingDescription

Parameter 6: Auxiliary/Emergency Mode

The Auxiliary/Emergency con!guration command enables or disables auxiliary / emergency heating in the thermostat.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 7: Thermostat Swing Temperature

The Thermostat Swing Temperature configuration command sets swing temperature on the Temperature thermostat.
Size: 1 Byte, Default Value: 2

SettingDescription

Parameter 8: Thermostat Differential Temperature

The Thermostat Differential Temperature configuration command sets the differential temperature for multi-stage HVAC systems.
Size: 2 Byte, Default Value: 4

SettingDescription

2 – 6| The thermostat differential temperature is in units of 0.5 degrees Fahrenheit.
---|---
0 – 1| 0x00 (Heat) or Cool (0x01)

Parameter 9: Thermostat Recovery Mode

The Thermostat Recovery Mode configuration command sets the HVAC recovery mode type. The recovery mode determines when additional HVAC stages are turned of as the ambient temperature returns to the target temperature.
Size: 1 Byte, Default Value: 2

SettingDescription

Technical Data

CoolEnergy Save HeatFan OnlyFurnaceHeat
Thermostat HVAC Systems Supported| Universal
Frequency| XXfrequency
Maximum transmission power| XXantenna

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>