TechniSat

Shutter

SKU: TECE9496

Quickstart

This is a
secure
Window Covering – Endpoint Aware
for
Europe.

To run this device please connect it to your mains power supply.

SmartStart enabled products can be added into a Z-Wave network” by scanning the Z-Wave QR Code present on the product with a” controller providing SmartStart inclusion. No further action is required” and the SmartStart product will be added automatically within 10″ minutes of being switched on in the network vicinity.

1. The Z-Wave QR-Code is located on the back of the product.

2. Please follow your SmartStart enabled Z-Wave gateway”‘s” manual, on how to use SmartStart inclusion.

3. Install the TechniSat Shutter.

4. After checking the correct installation, re-enable electrical” power at the main fuse or circuit breaker”
5. The TechniSat Shutter will be added to your Z-Wave network” within 10 minutes after re-enabling electrical power.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Designed as a drop-in replacement for your shutter wall switch from leading brand manufacturers, TechniSat”‘s Shutter-Switch integrates your wall switch into the Smart Home future. Featuring Z-Wave SmartStart and S2 security for easy installation and secure operation, your shutter switch can now be controlled from your Smart Home as well. Full manual operation can trigger central scenes via multiple button clicks. Short circuit and overload protection monitoring.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

1. When the roller shutter is in the lowermost position, press” and hold T2 for more than 20 seconds.

2. The LED will alternately flash red and green for 5 seconds” after a successful reset.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Installation

L Live lead

1 Switched output to shutter motor – up direction

2 Switched output to shutter motor – down direction

N Neutral lead

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

1. Install the TechniSat Shutter.

2. After checking the correct installation, re-enable electrical” power at the main fuse or circuit breaker.

3. Start the Z-Wave device add mode on your Z-Wave gateway,” according to the gateway”‘s manual.

4. Press T1 3x within 1 second.

5. The red status LED is on while the device is added to the” Z-Wave network.

6. The green LED is on for 5 seconds after successfully adding” the device.

Exclusion

1. Start the Z-Wave device remove mode on your Z-Wave” gateway, according to the gateway”‘s manual.

2. When the roller shutter is in the uppermost position, press” and hold T1 for more than 10 seconds.

3. The red status LED is on while the device is removed from the” Z-Wave network.

4. The green LED is on for 5 seconds after successfully removing” the device.

Product Usage

T1 – T4… Buttons

Central Scene

The TechniSat Shutter can send central scene activation notifications to” a Z-Wave gateway.

Pressing the respective button multiple times, will send the” corresponding scene number:

Button / Scene number
T1 / 1
T2 / 2″  ”  ”  “

T3 / 3
T4 / 4

The following Z-Wave key attributes are available for all scenes:

Button pressed Z-Wave key attribute

two times Key Pressed 2 times

three times Key Pressed 3 times

four times Key Pressed 4 times

five times Key Pressed 5 times

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Firmware-Update over the Air

This device is capable of receiving a new firmware ‘over the air’. The update function
needs to be supported by the central controller. Once the controller starts the update
process, perform the following action to confirm the firmware update:

1. Follow your Z-Wave gateway”‘s manual, on how to update the” firmware of a Z-Wave device.

2. From your gateway issue a Z-Wave request to get the current” firmware version of the device to be updated.

3. When the request has been received, your device”‘s LED will” glow red for 10 seconds.

4. While the LED glows red, press T1, T2, T3 or T4 to allow” a firmware update – the LED will now glow green for 10″ seconds.

5. While the LED glows green, start the device”‘s firmware update” from your gateway.

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

current state of the device.

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Central Scene

Enable/disable central scene notifications for 2x-5x button presses.
Size: 1 Byte, Default Value: 1

SettingDescription

0| Setting this parameter to 0 will disable central scene notifications for multiple (2x-5x) button presses.
---|---
1| Setting this parameter to 1 will enable central scene notifications for multiple (2x-5x) button presses.

Parameter 2: Wattage Time Report

Interval of current wattage meter reports in 10 seconds increments.
Size: 2 Byte, Default Value: 3

SettingDescription

3 – 8640| Interval of current wattage meter unsolicited reports in 10s increments (30 seconds – 1 day)
---|---
0| Disable unsolicited meter reports of current wattage.

Parameter 3: Energy Meter Report

Interval of active energy meter reports in minutes.
Size: 2 Byte, Default Value: 60

SettingDescription

10 – 30240| Interval of active energy meter unsolicited reports in minutes (10 minutes – 3 weeks)
---|---
0| Disable unsolicited meter reports of active energy.

Parameter 4: Calibration

Manual shutter calibration – shutter will move up, down and up again
Size: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic V2
• Central Scene V3
• Configuration
• Device Reset Locally
• Firmware Update Md V4
• Manufacturer Specific V2
• Meter V4
• Notification V8
• Powerlevel
• Security
• Security 2
• Supervision
• Switch Multilevel V4
• Transport Service V2
• Version V3
• Zwaveplus Info V2

Controlled Command Classes

• Basic V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>