GAINSBOROUGH Suits 35mm to 45mm Door Thickness Lock Instruction Manual

GAINSBOROUGH Suits 35mm to 45mm Door Thickness Lock

Overview

External View

Exploded View

Installation Instructions

Step 1: Prepare the Door
Fold template where indicated.

• Position the template on the door edge at desired lock/latch height.
• Firmly hold the template and mark the latch height and hole positions at desired backset.
• Reverse the template fold and mark the other side of the door.
• Measure the door thickness and mark the center on the “latch height” marking.
• Drill Ø25mm latch hole. Note: it is important to drill this hole squarely.
• Drill pilot holes. (suggested size Ø3 mm) Then enlarge the holes following the installation template instructions.
• Drill Ø10 mm and Ø54 mm holes from both sides of the door.
• Mark and chisel the latch faceplate to a recess of 4.0 mm. Use the latch as a template.

Step 2: Install the Latch
Install the latch with the tapered (beveled), side of the bolt facing towards the door jamb when the door is open.

Step 3: Prepare the Internal Furniture
Using the supplied battery cover release tool, push through the hole to release the battery cover to expose the mounting screw holes.

Step 4: Handing of the Internal Lever

• Rehand the lever (if necessary), by pushing the retaining plate inside the furniture as shown. (Push through the hole on the same side as the lever.)
• Then swing the lever up and over to the other direction.

NOTES:

• Carefully follow these instructions when installing.
• Do not overtighten screws.
• The use of a power driver is not recommended for screw installation.
• Fully remove the Gainsborough Freestyle prior to painting the door to avoid damaging the product’s finish
• Suitable door thickness is between 35 and 45mm

Step 5: Handing of the External Furniture

• Rehand the lever (if necessary), by pushing the retaining plate inside the furniture as shown. Push through the hole on the same side as the lever.
• Then swing the lever up and over to the other direction.

Step 6: Assemble the External Furniture to the Door
Install the External furniture onto the door as shown.

Step 7: Install the Spindle
Fit the Spindle Spring to the Spindle, and then assemble through the latch into the External Handle.

Step 8: Connect the Internal Furniture
Connect the main loom to the Internal furniture.

Step 9: Connect the Internal Furniture
Ensure the internal and external drive “D” shaft and socket are aligned

Step 10: Secure the Internal Furniture

Install the Internal furniture, taking care:

1. to align the “D” shaft/socket and the latch spindle
2. to ensure the loom is not pinched during assembly. This is very important.

Fasten the Internal Furniture to the External Furniture using the 4 screws supplied with the Allen Key

Step 11: Installation of Batterie s
Install the batteries and fit the battery cover.

Use only good quality AA ALKALINE batteries.

• Note the orientation of the batteries.
• Do not mix old and new batteries.

Step 12: Installation of the Strike
All door seals must be fitted prior to fitting the strike plate.

• Position the door so that the center point of the strike plate can be marked on the door frame.
• Mark and drill a Ø25mm hole to a depth of 25mm, at a corresponding height to the bolt.
• Mark and chisel recesses for the strike plate
• Fit the strike plate using the 2 screws supplied.

Door Position Sensor Installation Connected Gainsborough Freestyle only

Step 1b: Prepare Door
Using the template provided, drill a Ø10mm hole in the side of the door as shown.

Step 2b: Install Door Position Sensor in Door

• Insert the Door Position Sensor cable through the Ø10mm hole.
• Extend it through the Ø54mm hole.
• Firmly press the magnet housing into the door edge until the front face is flush with the door edge.

Step 3b: Connect Door Position Sensor
Connect the Door Position Sensor cable to plug in the Main cable

Step 4b: Install Door Position Magnet
Drill a Ø10mm hole for the Door Position Magnet and fit the magnet as shown .

Setting First User Admin Code

• Step 1:
  Facing the Internal lockset, locate the Program button above the batteries. Press and hold for 10 sec. After approx. 10 sec., the confirmation light will blink.

• Step 2:
  On the External side, slide cover up to energize Keypad.

• Step 3:
  Press ‘ , choose ‘ 1 ‘ then ‘’.

• Step 4:
  Enter desired 4-digit PIN code then press *‘’.**

• Step 5:
  The PIN code will repeat. Press *‘’** again to accept PIN Press ‘ ’ to reject the PIN.

Gainsborough Freestyle Function with Keypad

• Step 1:
  Slide cover up to energise Keypad.
  Refer to User Guide for full Gainsborough Freestyle functionality.

• Step 2:
  To UNLOCK – Enter 4 digit PIN code and press ‘ ‘.
  Note: The lockset must be in a LOCKED state.

• Step 3:
  To PRIVACY LOCK – Press ‘ ‘ when leaving.
  Note: The lockset must be in an UNLOCKED state.

• Step 4:
  To DEADLOCK – Enter 4 digit PIN code and press ‘ ‘ when leaving.
  Note: The lockset must be in an UNLOCKED state.

Gainsborough Freestyle Manual Function

PASSAGE MODE

• Outside UNLOCKED
• Inside UNLOCKED

PRIVACY MODE

• Outside LOCKED
• Inside UNLOCKED
• Press the Button to engage in Privacy mode.
• Unlock by external key, keypad, or internal by operating lever.

DEADLOCK MODE

• Outside LOCKED
• Inside LOCKED
• Note: DEADLOCK can only be set via the Keypad (see above).
• Unlock by external key, keypad or internal key.

Contact Information

Al legion Australia
Freephone 1800 098 094
Freefax 1800 098 095
Email auinfo@allegion.com.
www.allegion.com.au.

Allegion New Zealand
Freephone 0800 477 869
Freefax 0800 477 868
Email nzinfo@allegion.com.
www.allegion.co.nz.

gainsboroughhardware.com.au.

References

• Gainsborough Hardware Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>