Haier QPFA08 Portable Air Conditioner Owner’s Manual

Haier QPFA08 Portable Air Conditioner

INSTALLATION INSTRUCTIONS

Questions? Call Haier at 866.907 .1566 or visit our Website at: haierappliances.com.

BEFORE YOU BEGIN
Read these instructions completely and carefully.

• I MPORTANT – Save these instructions for local inspector’s use.
•   IMPORTANT – Observe all governing codes and ordinances.
• Note to Installer- Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical skills.
• Completion time -Approximately 1 hour
• We recommend that two people install this product.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner.

ELECTRICAL REQUIREMENTS

• Some models require a 115/120-volt AC, ‘(i.} 60-Hz grounded outlet protected with a 15-amp time-delay fuse or circuit breaker.

• The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.
  CAUTION

  • Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
  • Do not change the plug on the power cord of this air conditioner.
  • Aluminium house wiring may present special problems ­consult a qualified electrician.

• Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button while plugged into the outlet. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.

Location Requirements

• Place the air conditioner on a flat, level surface in a location that is at least 30″ (76.2 cm) from any wall.
  NOTE: A minimum clearance of 30″ (76.2 cm) from the air conditioner to the wall must be maintained to ensure proper airflow.

• Maintain a minimum 30″ (76.2 cm) clearance around the air conditioner to not block airflow.

• Keep the air conditioner free of any obstructions such as drapes, curtains, blinds, etc.

• The exhaust hose should be free of any obstructions.

• Do not place the air conditioner on an unstable or raised surface because it could fall and cause damage or injury.

• Do not place the air conditioner in direct sunlight or near a heat source such as baseboard heaters, stoves, etc.

• The window panel can be installed in a window with a minimum 20″ (55.88 cm) to a maximum 46″ (121.92) opening.

PARTS INCLUDED (Appearance may vary)

1. Handle
2. Air Inlet Grille (Up)
3. Control Panel
4. Casters
5. Louver
6. Air Outlet Grille
7. Drainage Hole
8.  Air Inlet Grille (Down)
9. Exhaust Hose Joint
10. Exhaust Hose
11. Exhaust Hose Adapter
12. Window Sealing Kit
13. Small Screw

UNPACK AIR CONDITIONER

WARNING

• Excessive Weight Hazard

• Use two or more people to move and install air conditioner.

• Failure to do so can result in back or other injury.

• Remove packaging materials. Save the carton and the foam packaging for storing the air conditioner when not in use.
  NOTE: There are NO packing materials inside the air conditioner to remove-Do Not open the cabinet.

• Properly dispose of/recycle all packing material.

• Handle the air conditioner gently.

• Keep the air conditioner upright and level. Do not set the air conditioner on its side, front, back or upside down.

INSTALL EXHAUST HOSE ASSEMBLY TO BACK OF UNIT

• To assembly exhaust assembly. Extend both ends of hose approximately 4 inches. Attach the exhaust hose joint by screwing on in a counterclockwise direction. Then repeat with exhaust hose adapter.

• To attach assembly to unit, position the rectangular exhaust connection above the square exhaust port on the back of unit. Slide the connector down to connect to unit.

INSTALL WINDOW PANELS

• Measure the window opening. For a 20″ opening, use just the middle panel of the Window Kit with the opening for the Exhaust Hose Adapter. For openings from 20″ to 33″, insert one side panel to the middle panel, for openings from 33″ to 46″, insert both side panels.

• Place the Window Kit into the window opening (the Cam Locks should be towards you) and slide the side panels (if being used) outward to fill the opening. Lock the panels in place with the Cam Locks. Apply the foam seals to the top, bottom and ends to provide the best seal. Slide the window shut against the Window Kit.

CONNECT EXHAUST HOSE TO THE WINDOW PANEL

• Place the Air Conditioner close to the window ensuring there is at least 20″ of clearance from the wall and any other obstructions.
• Extend the hose so that it reaches the Window Kit. Insert the Exhaust Hose Adapter  into the opening in the Window Kit and slide it into the locking position. Ensure that the hose runs straight to the window with no excess extension.
  Important: The Air Conditioner must be vented to the outside. Do not use a longer hose or extend the hose included with the Air Conditioner or the unit will not cool properly and will overheat.

COMPLETE INSTALLATION

WARNING

• Electrical Shock Hazard
• Plug into a grounded 3 prong outlet.
• Do not remove the ground prong from the power cord plug.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to do so can result in death, fire or electrical shock .

1. Plug the power cord into a grounded 3 prong outlet.
2. Press the Reset button on the plug to ensure the safety plug is providing power to the Air Conditioner.
3. Allow 20″ of clearance around the Air Conditioner for proper air circulation
4. When removing the Air Conditioner, be sure to remove the Window Kit.

TROUBLESHOOTING TIPS

Error Codes

LIMITED WARRANTY

In Order to Make a Warranty Claim During the First 90 Days from the Date of Original Purchase:

• Properly pack your unit, We recommend using the original carton and packing materials.
• Return the product to the retail location where it was purchased.
• Include in the package a copy of the sales receipt or other evidence of date of original purchase. Also print your name and address and a description of the defect.

In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

• Locate your original sales receipt and make a note of your Please return all requested materials (postage pre-paid) model and serial number.
• Visit haierappliances.com to initiate the product replacement process.
• You will be asked to provide your name, address, date of purchase, model and serial number.
• Haier Appliances will arrange for a carton to be sent to your home to recover the product.

What Will Not Cover:

• Customer instruction. This owner’s manual provides information regarding operating instructions and user controls.
• Replacement of house fuses or resetting of circuit breakers.
• Failure due to corrosion on models not corrosion protected.
• Improper installation. If you have an installation problem, or if the air conditioner is of improper capacity, contact your dealer or installer. You are responsible for providing adequate electrical connecting facilities.
• Failure of the product resulting from modifications to the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.
• Damage to the product caused by improper power supply voltage, accident, fire, floods or acts of God.
• Incidental or consequential damage caused by possible defects with this air conditioner,
• Damage caused after delivery.

EXCLUSION OF IMPLIED WARRANTIES – Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

For US Customers:

• This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a Haier Appliances Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized Haier Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.
• Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

ABOUT COMPANY

• Warrantor US:
  • GE Appliances, a Haier company
  • Louisville, KY 40225
  • For customers in Canada: This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within Canada.
  • Warrantor Canada: MC Commercial Inc., Burlington, Ontario, L7R5B6

References

• Kitchen appliances for small spaces | Haier Appliances
• Ductless Registration | Haier Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>