swim fun 2778562 Surface Skimmer Pump User Manual

: June 9, 2024
: swim fun

Table of Contents

USER MANUAL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

swim fun 2778562 Surface Skimmer Pump A01

USER MANUAL

SURFACE SKIMMER PUMP

swim fun 2778562 Surface Skimmer Pump A01

1. The package contains

Power supply
Filter cover
Filter cartridge
Casing
Pump housing and base plate with motor and supply cord.
Pump holder with clamp and edge clamp.

1. 2. 3.

4. 5. 6.

Read the instructions carefully before installation

2. Technical specifications

Article no.	1561
Mains voltage	12VAC
Filter volume	2.8 L
Water flow	1,700 litres per hour
Maximum water volume	10,000 litres
Frequency	50 Hz.
Power consumption	20 Watts
Maximum water temperature	35º C
Maximum submersion depth	0.5 metres
Remarks	Low-pressure filter pump with transformer

Transformer model: Type: SG12 20.4 W. Input: 230V 50 Hz. Output 12VAC 1,700 mA 20.4VA

3. Safety instructions

The filter system is of a low-voltage type, and it is protected against water penetration. If the power cord or other components are damaged, the entire filter pump must replaced before the system is safe to use.

Disassembly of the skimmer filter

If there is damage to the filter system, the procedure is as follows:

Disconnect the system from the power source
Remove the filter from the pool
Remove the pump from the filter system

Winter storage

The filter system should be removed and stored in a frost-free place over the winter. The filter system must be also be removed when it is not going to be used for a long period of time. When removing, clean the filter before it dries out. After being stored over the winter the system is put back in the pool as described for the initial operation.

Safety regulations

There must be a minimum distance of 3.5 metres between the transformer and the pool
Electrical installations must be performed by an authorised electrician
The filter system must be turned off when the pool is being used
The filter system must NEVER run without water
Do not touch the system with wet hands while it is running
If the filter needs to be handled, it must always first be disconnected from the power source
If the filter needs to be handled, it should always be done on a dry surface
Never store the filter in a damp place, as it may lead to an electric shock
Children and adults should never sit/lean on the filter
If the power cord becomes damaged, the entire installation must be replaced
Any questions should be directed to the pool distributor or to info@swim-fun.com

4. Initial operation

Warning
Never run the pump without water. It will lead to damage to the pump.

This filter system is designed for use in swimming pools with fresh water. This is an IPX8 safety class electrical device (resistant to penetration by dust, solid particles and moisture).

Connection of the filter

The transformer must be connected to a standard 230V 50 Hz power source that is protected with a residual current device. The instructions in this manual must be carefully followed. The filter system is placed in the pool facing the prevailing wind so that any dirt on the surface reaches the filter more easily.

The skimmer filter and filter holder are mounted on the edge of the pool. The two screws at the top of the filter holder are fastened. Loosen the holder and place the skimmer filter so far down that the top edge is just below the water level. Note that the upper edge should be located approximately halfway on the holder. Tighten the holder again. The filter pump must be completely submerged in the water and be completely filled with water.

In order to avoid air being sucked into the pump during installation, it should be submerged at least 15 cm below the water surface.

The filter system is now ready for use.

The pump should be stored indoors during the winter in order to avoid frost damage.

The pump should always be positioned below the water surface in order to avoid unnecessary power consumption.

Note
The pump is activated as soon as the transformer is connected to the mains.

5. How the filter system works

Filter system uses a 12V surface pump with low voltage to circulate the water through a filter cartridge. There must always be water in the pump when it is running. The pump has an overload switch in order to avoid damage due to overheating. This switch automatically turns on again once the motor has cooled down. The filter cartridge filters the water for dirt, algae, oils, etc. The filter must be cleaned by rinsing it under the tap (see the next section on cleaning and maintenance).

Starting the pump

The pool must be filled with water up to above the edge of the filter. This makes the water flow into the filter making it ready for use. NEVER attempt to start the pump unless there is enough water in the pool!

The filter will capture hair, insects, leaves, and other large impurities in the water. Always keep the filter clean of dirt so as not to overload the pump.

Plug the pump into a power socket.

The filter in operation

The filter now runs in a normal filter routine. Continue to filter the pool water, until it is clear and clean.

The filter must run a minimum of 2 x 4 hours daily so that the water will be filtered twice a day. Between each interval the pump will be idle for a few hours. Connect a timer if necessary. In periods of hot weather and when there is a lot of bathing activity, the filter time must be increased, as does the need for water care products.

When the filter is clean, the pump has a maximum effect. On the other hand, if the filter is clogged with accumulated dirt, the water will not be able to circulate properly. Remember to inspect the filter as soon as the flow decreases, or each time the pump has been running for 5 hours - depending on whichever comes first. If the filter looks dirty - it should always be cleaned!

6. Cleaning and maintenance

Isolate the power source
Remove the filter (lift the filter cover and unscrew the filter cartridge).
Rinse the filter with a garden hose or under the tap. The filter can also be cleaned in a dishwasher. Rinse both the inside and the outside. Additional cleaning can be done by rinsing the filter in hot soapy water. If there are small calcium deposits in the filter layers, it no longer cleans effectively, and must therefore be replaced with a new filter. The filter is clogged with algae and dirt, so use an extra powerful water jet for cleaning. Never let the filter dry out, as it makes the filter difficult to clean and destroys it. Always have a spare filter ready for use.
Put the filter back into the skimmer. Carefully tighten the screws and close the filter.
Turn on the power source and continue the filtering.

YOU MUST KEEP THE FILTER CLEAN AT ALL TIMES IN ORDER TO MAINTAIN THE CORRECT WATER FLOW IN THE POOL!

Only use the filter that fits this pool. The filter must be covered with water at all times, otherwise there is a risk of damage to the pump.

Never add chemicals directly into the skimmer. These should instead be dissolved in a bucket of water, before being added along the edge of the pool. Alternatively use a child-proof floating chlorine dispenser.

See more about water care and pool accessories at your local pool distributor, or click on www.swim-fun.com

7. Replacing the pump

Isolate the power supply and remove the pump housing from the pool.

Undo the black mounting plate by pushing it in and turning it anti clockwise. IMPORTANT: Do not take hold of the motor. It will destroy the spring inside.

Lift the motor and filter out of the pump housing.

Unscrew the filter by taking hold of the bottom plastic edge and turning it anti clockwise until the filter is loose from the black mounting plate.

The mounting plate is now ready for a new filter.

Screw the filter onto the mounting plate, by turning it clockwise.

Locate the filter and the motor in the pump housing so that the notches on the edge of the mounting plate fit the edge of the pump housing.

Fasten the black mounting plate by pushing it in and turning it clockwise. IMPORTANT: Do not take hold of the motor. It will destroy the spring inside.

8. Warranty

The product is covered by a 12-month warranty (plus 12-month right to claim). The warranty period applies from the date of purchase on your purchase receipt. Proof of purchase must be provided when claiming for service under the guarantee. NB: Keep your purchase receipt in a safe place! The warranty does not cover normal wear and tear, scratches, abrasions or cosmetic damage. More specifically, the warranty does not cover damage caused as a result of:

Incorrect use or handling, including frost damage occurring as a result of inappropriate storage.
Fall or shock
Repairs, changes or similar conducted by a party other than a Swim & Fun Service Centre.

In the event of a warranty claim, contact your dealer. When returning a defective item it must be packaged so that the product is protected against transport damage. It is your responsibility that the product arrives safely. Please include your name, address and email – to enable us to return the product to you. Do not forget to tell us what is wrong with the product.

For more user information and tips, visit our website:www.swim- fun.com.

This manual is protected under the provisions of the Danish copyright legislation.

Swim & Fun - hotline:

Denmark +45 7022 6856
Sweden +46 771 188819

9. Responsible Disposal

This symbol indicates that this product should not be disposed of with general household waste. This applies throughout the entire EU. In order to prevent any harm to the environment or health hazards caused by incorrect waste disposal, the product must be handed in for recycling so that the material can be disposed of in a responsible manner. When recycling your product, take it to your local collection facility or contact the place of purchase. They will ensure that the product is disposed of in an environmentally sound manner.