swim fun 1924 2 in 1 Drain Pump User Manual

: June 9, 2024
: swim fun

Table of Contents

Your appliance at a glance
Description
General safety instructions
Installation and commissioning
Cleaning and maintenance
Malfunctions and troubleshooting
Technical data
Guarantee
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

1924 2 in 1 Drain Pump
User Manual

swim fun 1924 2 in 1 Drain Pump -

Your appliance at a glance

Art. 1924

Carrying handle
Mains cable and plug
Sensor switch
Hose adapter
Pump casing
Sensor switch socket
6-1 Sensor position for constant running
6-2 Sensor position for having different pump starting water level
6-3 Sensor position for having the lowest pump starting water level at 10mm.
Baseplate

Description

Your new appliance was designed and manufactured to the current state of the art. Read these instructions for use carefully before using the appliance for the first time! hese
instructions contain all information necessary to safely use this appliance and provide for its extended lifespan. Please make sure to observe all safety information included in hese instructions!
The appliance is intended for pumping rainwater, fresh water, mains water and chlorina ted swimming pool water. It must not be used for the drinking water supply or for the de livery of foodstuffs. Explosive, flammable, aggressive or health-hazardous substances and faecal matter must not be pumped. Any use considered improper or npredictable damage can occur as a result of improper use, modifications to the appliance or due to the use oparts which have not been tested and approved by the manufacturer!

General safety instructions

To operate this appliance safely, the user must have read and understood these in structions for use before using the appliance for the first time.
Always keep the operating instructions within reach.
If you sell or pass the appliance on, you must also hand over these operating instructi ons.
Observe all safety instructions! Failure to do so may cause harm to you and others.
Do not use the appliance in potentially explosive areas or in the vicinity of flammable liquids or gases!
Do not touch the mains plug with wet hands! Always disconnect the mains plug by pulling the plug and not the cable.
The connection must be made to earthed sockets which have been properly installed, earthed and tested. Mains voltage and fuse must comply with the technical data.
During operation for swimming pools, garden ponds and similar places, the appliance must be equipped with a residual current circuit breaker (RCCB) with a design fault current no more than 30 mA.
Do not kink, crush, drag or drive over the mains cable; protect against sharp edges, oil and heat.
Extension cables must not be used.
Disconnect the mains plug before all work on the appliance.
Do not install and switch on the appliance if there are people or animals in the medium being pumped (e. g. a swimming pool), or they are in contact with it.
Children and young people under the age of 16 years must not use this appliance, and must be kept away from it when it is in operation.
Repairs must be carried out only by a qualified electrician. If repairs are carried out incorrectly, there is a danger of liquid penetrating into the electrical components of the appliance..

Installation and commissioning

Attach a sufficiently long and strong rope to the specially designed bottom plate position before first use when the pump is placed onto the pool cover or attach a sufficient long and strong rope to the handle before first use when the pump needs to be submerged into the water container as submersible pump.
Connect pressure pipe
For occasional use, use a suitable water hose.
The use of rigid pipes with a non-return valve is recommended for use at a fixed location.
This prevents return flow of the liquid when switching off.

Screw the pressure hose onto the hose adapte.
All threaded connections must be sealed with thread sealing tape (e. g. Teflon® tape).
When using a hose, screw a suitable hose adapter onto the hose adapte.
Push the hose firmly onto the hose adapter and secure with a hose clamp.

Operation
By adjusting the position of sensor switch in support to have different pump starting water level. This product provides several vertical adjustment positions.
OBS
Do not lift the pump with the cable or pressure hose as these are not designed for the tensile stress from the weight of the pump.
Installation
The appliance can be put on the pool cover when the base plate is fitted or in the water container when the base plate is taken off.
The appliance can be submerged under water up to the submerged operating depth mentioned in the technical data.
When using as submersible pump, Install the appliance so that the suction openings cannot be blocked by foreign bodies (place the appliance on a firm, even base if necessary). Ensure that the appliance is stable.
Submerge the pump at an angle into the liquid to be delivered so that no air pocket forms on the underside of the appliance. Suction would be prevented by this. When using as a submersible pump, Leave the pump on the bottom of the liquid container. Use a strong rope attached to the carrying handle of the pump for lowering. Tighten the end of the rope firmly after lowering.
By adjusting the position of sensor switch in support to have different pump starting water level. This product provides several vertical adjustment positions.

swim fun 1924 2 in 1 Drain Pump - Fig1

Notice
For operation with rope: Do not operate the pump without pressure hose. Avoid the pump twisting around its longitudinal axis. fore every use

Cleaning and maintenance

Before every use
Check casing and cables for damage and check sensor switch if damage or not.
After every use
Clean the appliance.
Cleaning the appliance externally
Rinse with clean water. Remove stubborn contamination with a brush and detergent.
Submerge the pump in a container with clean water and switch on for a short time to rinse the inside of the pump.
Cleaning the suction area
Take off the base plate and filter sponge, rinse the bottom of the pump with clean water thoroughly. Remove stubborn contamination with a brush and detergent.

Storing
If there is a risk of frost, dismantle the appliance and accessories, clean them and store in a place protected from frost.
The appliance can be put on the pool cover when the base plate is fitted or in the water container when the base plate is taken off.
The appliance can be submerged under water up to the submerged operating depth mentioned in the technical data.
When using as submersible pump, Install the appliance so that the suction openings cannot be blocked by foreign bodies (place the appliance on a firm, even base if necessary). Ensure that the appliance is stable.

Malfunctions and troubleshooting

Minor faults are often sufficient to cause a malfunction. In most cases, you will be able to correct these faults easily yourself. Please start by referring to the following table before contacting our technical support. This will help you save much effort and possibly expense.

Fault/malfunction	Cause	Remedy
Pump does not run.	No mains voltage?	Check cables, plug, socket and fuse.

Motor overheats due to:
• liquid temperature too high?
• blocking by foreign bodies?| Eliminate the cause of the overheating
Residual current circuit breaker (RCCB) triggered?| Activate RCCB. Contact qualified electrician if RCCB triggers again.
Motor defective?| Contact service partner.
Pump runs but does not pump.| Suction openings blocked?|
Pump draws in air?| Keep the pump at an angle while submerging.
Switch the pump on and off several times in order to expel air.
Pump blocked by foreign bodies?| Clean the pump
Delivery rate too low.| Pressure hose diameter too small?| Use pressure hose with larger diameter
Pressure hose blocked?| Rectify blockage.
Suction openings blocked?| Clean suction opening.
Pressure hose kinked?| Straighten pressure hose.
Pressure hose leaks?| Seal pressure hose, tighten threaded connections.
Pump runs very loudly.| Pump draws in air?| Ensure there is sufficient liquid present.
Keep the pump at an angle while submerging.

Technical data

Model	SMPC-200
Rated voltage / Frequency	230 V ~ / 50 Hz
Rated power	200 W
Protection class	IPX8
Max. supply height	8

Service
We have specialist knowledge of our products and the field in general, so you can get help quickly and easily. If you have any questions or need more information, please feel free to call.
Customer service on +45 70 22 68 56.
If you need service or to make a warranty claim, you must create a case directly in our support system. Go to the home page under SUPPORT.

Guarantee

The product is covered by a 12-month guarantee (plus 12-month right to claim). The warranty period applies from the date of purchase on your purchase receipt. Proof of purchase must be provided when claiming for service under the guarantee. NB: Keep your purchase receipt in a safe place!
The guarantee does not cover normal wear and tear, scratches, wear and tear or cosmetic damage. Specifically, the guarantee does not cover damage caused as a result of:

Improper use or handling including frost damage by improper storage.
a fall or shock
Repairs, modifications or etc. performed by anyone other than Swim & Fun Scandinavia servicecenter.

Complaints
If you have a claim, you must contact Swim & Fun Scandinavia at swim- fun.com/Support. By submission of a defective item it must be packaged so that the product is protected against transport damage. It is your responsibility that the product arrives safely. Please notify us on your name, address and e-mail – to enable us to return the product to you. Remember to let us know what is wrong with the product.

Responsible Disposal
If you have a claim, you must contact Swim & Fun Scandinavia at swim- fun.com/Support. By submission of a defective item it must be packaged so that the product is protected against transport damage. It is your responsibility that the product arrives safely. Please notify us on your name, address and e-mail – to enable us to return the product to you. Remember to let us know what is wrong with the product.

Customer service:
swim-fun.com/support
Danmark +45 7022 6856
Sverige +46 771 188819
© All rights reserved Swim & Fun A/S 2022
Swim & Fun A/S
Ledreborg Allé 128 K, DK-4000 Roskilde
info@swim-fun.com . www.swim-fun.com