SeeK thermal AttackPRO Desktop Charger User Guide

: June 3, 2024
: Seek thermal

Table of Contents

Safety and usage information
What’s included in the box
Illustrations
Cleaning and care
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AttackPRO desktop charger quick
start guide

Important safety information. Read entire manual before use.

Safety and usage information

FCC Statement:
This device has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Operation is subjected to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Note: Modification to this product will void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-3 (A)/NMB-3(A)

IC Statement:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
European Union:
RFI Emissions: EN 61000-6-3
Immunity: EN 61000-6-2
Electrical Safety: EN/IEC 61010-1
ROHS: This RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Seek Thermal ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.

WEEE: This symbol on the product(s) and / or accompanying documents means that used electrical and electronic equipment should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. Alternatively, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Important safety information
WARNING – INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY
CAUTION – INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN MINOR OR MODERATE INJURY
NOTICE – INDICATES INFORMATION CONSIDERED IMPORTANT, BUT NOT HAZARD- RELATED

WARNING

Never recharge in a potentially explosive environment.
A lithium battery with a damaged enclosure should not be exposed to water.

CAUTION

This desktop charger is intended to be mounted on a flat and stable surface in a suitable location where there is no risk of physical impact or acceleration forces.
Remove any water or moisture from the battery before you install it. Do not apply solvents or equivalent liquids to the enclosure, cables, or other items. Damage to the components can occur.
Disconnect the AttackPRO desktop charger from the AC power source before cleaning.

NOTICE

Use only an approved power supply provided by Seek Thermal.
As with most electronic products, this equipment must be disposed of in an environmentally friendly way and in accordance with existing regulations for electronic waste.
Do not alter or cover over any labels on the desktop charger.
This desktop charger should be placed in a location that is average room temperature (73˚F/ 23˚C), protected from weather, water, chemicals, and direct long term sunlight exposure.
The charger is suitable only for indoor use.
Always purchase the battery recommended by the device manufacturer for the equipment.
Contact your distributor for servicing by authorized personnel. This component contains no user-serviceable components.
Clean the battery contacts and also those of the equipment prior to battery installation.

What’s included in the box

Desktop charger cradle
Power supply (for battery charger)
AC plugs for US, EU, and UK (for Power Supply)
Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product specifications at any time without prior notice.

Illustrations

SeeK thermal AttackPRO Desktop Charger

Equipment rating s

Supply Voltage	10W
Power Rating	5VDC
Environmental	Intended for indoor use

Quick start guide

Please refer to the following to start using the product right away:

Place the desktop charger on a suitable stable surface.
Plug the barrel end connector of the power supply into the back of desktop charger.
Determine the appropriate AC plug interface (US/EU/UK) for your region and attach to the power supply face.
Plug the power supply into a safe AC power source.
Place the battery with the label facing outward and the charging contacts pointed downward, aligning the rib on the back of the battery pack with the well in the charger.
The LED on the charger should light as follows:
a. Solid RED = battery is charging.
b. Solid GREEN = battery is fully charged.
c. Blinking RED = there is an error with charging.

Cleaning and care

The AttackPRO battery charger requires little maintenance. For best care, please follow the guidelines below:

Unplug the AC power supply from the AC power source before any cleaning
Gently use a cotton swap damped with isopropyl alcohol to wipe the contacts if they appear dirty or covered with debris
To clean the charger housing, use a soft cloth with warm water only and a mild detergent. Do not use solvents to clean the charger
Do not allow any liquids or debris to enter the charger
Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product specifications at any time without prior notice.

Customer and product support
For any questions or issues with the use of this product, do not hesitate to contact our customer support group at www.thermal.com/support.

Troubleshooting

If you are experiencing problems with your product, please refer to this checklist. If the problem persists, please contact Seek Thermal Customer Services or your local distributor.
Power and charging

Issues:	Solutions:
LED does not light when battery is inserted.	Ensure battery is inserted

correctly.
Ensure AC power source is adequate and safe.
Ensure battery contacts are clean.
Battery will not charge.| Ensure battery is inserted correctly.
Ensure AC power source is adequate and safe.
Ensure battery contacts are clean.
RED flashing indicator when battery inserted.| Clean battery charging contacts.

Seek Thermal Inc.
6300 Hollister Avenue
Santa Barbara, CA 93117
www.thermal.com
www.thermal.com/support

Disclaimer
Specifications subject to change without further notice. Models and accessories subject to regional market considerations. License procedures may apply. Products described herein may be subject to US Export Regulations. Please refer to thermal.com/support with any questions.

www.thermal.com