Seek thermal Attack Pro Truck Charger User Manual

Seek thermal Attack Pro Truck Charger

READ ENTIRE MANUAL BEFORE USE

AttackPRO Series truck charger

Important safety information. Read entire manual before use.

Safety and usage information

FCC Statement:
This device has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Statement:
CAN ICES-003 (B) / NMB-003 (B)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
European Union:

• RFI Emissions: EN 55032
• Immunity: EN 55035
• Electrical Safety: EN/IEC 62368-1
• ROHS: This RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Seek Thermal ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.
• WEEE: This symbol on the product(s) and / or accompanying documents means that used electrical and electronic equipment should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. Alternatively, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Important safety information
WARNING
INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY

CAUTION
INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN MINOR OR MODERATE INJURY

NOTICE
INDICATES INFORMATION CONSIDERED IMPORTANT, BUT NOT HAZARD-RELATED

WARNING

1. Never recharge in a potentially explosive environment.
2. A lithium battery with a damaged enclosure should not be exposed to water.

CAUTION

1. This truck charger is intended to be mounted on a flat and stable surface in a suitable location where there is no risk of physical impact or acceleration forces.
2. Alternatively, this truck charger may be securely mounted to a vertical or horizontal surface in a location deemed safe and appropriate by the party rforming the installation
3. Remove any water or moisture from the battery before you install it. Do not apply solvents or equivalent liquids to the enclosure, cables, or other items. Damage to the components can occur.
4. Disconnect the AttackPRO truck charger from the AC power source before cleaning.

NOTICE

1. Use only an approved power supply provided by Seek Thermal.
2. If choosing to mount and hardwire the truck charger in any apparatus, make sure installation is done by professional installers.
3.  As with most electronic products, this equipment must be disposed of in an environmentally friendly way and in accordance with existing regulations for electronic waste.
4. Do not alter or cover over any labels on the truck charger.
5. This truck charger should be placed in a location that is average room temperature (73˚F/ 23˚C), protected from weather, water, chemicals, and direct long term sunlight exposure.
6. The charger is suitable only for indoor use.
7. Only for use with Seek Thermal AttackPRO Cameras (model FQ-PPAX, FQ-PPNX and model FA-BAA Battery Pack).
8. Contact your distributor for servicing by authorized personnel. This component contains no user-serviceable components.
9. Clean the battery contacts and also those of the camera prior to component installation.

What’s included in the box

• Truck charger unit
• Power supply (for AC power)
• AC plugs for US, EU, and UK (for Power Supply)
• Accessory Kit : Fuse holder/fuse, Self-tapping mounting fasteners x 3, 12/24VDC Terminal connector, Feet for desktop/table use x 4.
•  Quick start guide

Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product specifications at any time without prior notice.

Illustrations

• Mounting hole locations
• Internal 3A fuse
• 12/24VDC terminal connector
• 12/24VDC input
• DC input jack
• Charger power LED indicator
• Battery charger well
• Battery charger cover plate
• Battery retention slot
• Battery strap
• Battery charging LED indicator
• Camera charger well
• Camera retention slot
• Camera strap

Technical Specifications

Equipment ratings

Please contact your local authority for further details of your nearest designated collection point.  The back surface of the truck charger allows connection to apparatus 12/24VDC systems using the terminal connector instead of the included AC/DC switching power supply. Please consult the appropriate installation services to safely and properly connect this to apparatus using the included terminal, fuse, and fuse holder.

Hardwiring and Mounting Instructions

1. Select a suitable mounting location inside the apparatus and refer to the hardwiring diagram in Section 6.

2. Use the AttackPRO truck charger itself (WITHOUT POWER CONNECTED) or use a template available from thermal.com to mark the mounting hole locations on the preferred mounting surface; these correspond to the 3 thru hole locations in the charger housing for mounting (a).

3. Install secured and permanent cables (not provided) running from the apparatus 12/24VDC supply to the rear of the AttackPRO truck charger at the selected mounting location, BUT DO NOT CONNECT THIS CABLE TO THE 12/24VDC SOURCE AT THIS TIME.

4.  This cable routing must contain an in line fuse installed close to the battery (a fuse and fuse holder
   is provided). Cables, crimps, and battery connectors are not provided.

5.  Connect the positive and negative wires that will terminate at the AttackPRO truck charger to the included terminal connector (c) (green). Plug the terminal connector into the rear of AttackPRO truck charger (d), routing any cables thru the appropriate channels for clearance.
   Note
   Check the polarity when you connect the cable to the terminal connector

6. Attach the truck charger to the selected surface using the included self tapping screws or other hardware necessary to ensure the unit is secure and safely mounted.

7. Permanently connect the positive and negative cables (not provided) to the apparatus 12/24VDC supply.

Hardwiring Diagram and System Overview

• Mounting hole locations
•  Fuse holder and fuse
•  Included terminal connector
• Terminal connector plug location

Quick start guide

1. 2. Place the truck charger on a suitable stable surface or securely mount to a horizontal or vertical surface, as above.

2. Plug the barrel end connector of the power supply into the back of truck charger (e), note power supply will need to be connected before step 1 if securely mounting the charger.

3. Determine the appropriate AC plug interface (US/EU/UK) for your region and attach
   to the power supply face.

4. Plug the power supply into a safe AC power source. The blue light on the charger (f) should indicate power received.
   Place the battery in the battery charger well (g) with the label facing inward and the charging contacts pointed upward, and under the top contact cover plate (h). Make sure the bottom of the battery is properly seated in the retention slot (i). Secure the battery with the attached strap (j).

5. The LED on the charger should light as follows:

  * Solid RED = battery is charging.
  * Solid GREEN = battery is fully charged.
  * Blinking RED = there is an error with charging.

7. Place the AttackPRO thermal imaging camera in the camera charger well (l), with the display facing outward, and the upper surface near the label fitting under the upper retention lip (m) of the well. Make sure the bottom of the camera is properly seated in the retention slot (n). Secure with the attached strap (o).
8. The display on the AttackPRO should light and indicate charging status. The display will go dark after approx. 3 seconds. To wake the display and check charge status, press any button on the camera.

Cleaning and care

The AttackPRO truck charger requires little maintenance. For best care, please follow the guidelines below:

• Unplug or disconnect the power supply from the power source before any cleaning
• Gently use a cotton swab damped with isopropyl alcohol to wipe the contacts if they appear dirty or covered with debris
• To clean the charger housing, use a soft cloth with warm water only and a mild detergent. Do not use solvents to clean the charger
• Do not allow any liquids or debris to enter the charger
• Damaged or broken retention straps may be field replaceable by removing either the battery or camera retention slots and inserting a new retention strap

Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product specifications at any time without prior notice.

Customer and product support

For any questions or issues with the use of this product, do not hesitate to contact our customer support group at www.thermal.com/support.

Troubleshooting

If you are experiencing problems with your product, please refer to this checklist. If the problem persists, please contact Seek Thermal Customer Services or your local distributor.

Power and charging

Power LED does not light when power source is connected to charger

| Ensure either the switching AC power supply is properly inserted into a working AC receptacle OR
Ensure the 12/24VDC hardwire source is properly providing power, check for blown fuse and replace if necessary.

Battery LED does not light when battery is inserted.

| Ensure battery is inserted correctly.
Ensure AC power source is adequate and safe.
Ensure battery contacts are clean.

RED flashing indicator when battery inserted.

| Try reinserting the battery.
Replace/charge battery.
Try an alternate battery.
Battery will not charge.| Clean battery charging contacts.

AttackPRO does not indicate charging when inserted.

| Make sure AttackPRO is properly seated in the charging well and making contact with the retention strap securely fastened.
Make sure a battery is installed in the AttackPRO and the battery door is secured.
Try inserting the battery only into the battery charge slot of the charger to note behavior.

Seek Thermal Inc.
6300 Hollister Avenue
Santa Barbara, CA 93117
www.thermal.com
www.thermal.com/support

Disclaimer
Specifications subject to change without further notice. Models and accessories subject to regional market considerations. License procedures may apply. Products described herein may be subject to US Export Regulations. Please refer to thermal.com/support with any questions.

www.thermal.com | PN 4307 REV3

References

• Seek Thermal | Affordable Infrared Thermal Imaging Cameras - Affordable Infrared Thermal Cameras
• Seek Thermal | Affordable Infrared Thermal Imaging Cameras - Affordable Infrared Thermal Cameras

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>