LUMBERJACK WB1520D2 Solid Wooden Bench User Manual

June 3, 2024
LUMBERJACK

LUMBERJACK WB1520D2 Solid Wooden Bench

Specifications

  • Vice Capacity: 7″ Inch
  • Top Shelf Weight Capacity: 113kg
  • Drawer Weight Capacity: 11kg
  • Bottom Shelf Capacity: 90kg
  • Dimensions (Including Vice):
  • L) 1520mm x W) 620mm x H) 820mm
  • Drawer Inside Dimensions (x4):
  • L) 365mm x W) 420mm x H) 70mm

Parts

Assembly instruction

Stage 1 Assembly of work bench frame.
Parts required for this section: A) x1, B) x4, C) x4, C1) x4, 1) x2, 2) x2 & 3) x1
Place the washer (C1) over bolt (C) and insert through the side leg (1) to attach the lower support bracket (2). Place the dowel nut into the pre cut hole on the support bracket (2) and tighten using the allen key (A)

Repeat this process again for the second side leg (1) for the bench to then look like the below image.

Insert bottom shelf (3) by sliding into the recess of the support bracket (2). Then attach the second support bracket (2) to the side legs (1) using bolt (C), washer (C1) & dowel nut (B)

Congratulations stage one is now complete.
Your bench should now look like the image below.

Stage 2 Attaching the drawer runners, upper support brackets & table top.
Parts required for this section: D) x8, E) x4, C1) x4, 4) x2, 5) x1 & 6) x1. (You will also require a cross headed screwdriver & a 13mm spanner) Attach upper support bracket (4) to the side leg (1) using screw (D)

Repeat this process for both support brackets (4) as per the image below.

To attach the middle drawer runner (6) use screw (D) ensuring the screw locates into the pilot hole on the middle drawer runner (6) as shown in below image.

Please ensure the middle drawer (6) match the side legs (1). Gap to the rear of the bench and flush to the front of the bench. As seen in image below.

Attach the table top (5), using screws (E) & washers (C1). Insert the screws from underneath the table top (5) to secure the bench frame.

Once you have secured the table top (5) with all four screws (E) & washers (C1) Your bench should then look like the image below.

Finally, attach the vice (7) to the front of the table top (5) into the pre drilled holes on the right.

Congratulations stage two is now complete. Your bench should now look like the image below.

Stage 3 Assembly of the drawers.
Parts required for this section: 8) x4, 9) x4, 10) x4, 11) x4, 12) x4, 13) x4, F) x32 & G) x8
(You will also require a cross headed screwdriver)
To assemble the drawer take both sides & back (8), (9) & (10). Place on the table top (5). Ensure the rails for the drawer are facing outwards and the recess to the bottom. Using screw (F) secure all three pieces together as shown in the images below.

Next slide the drawer bottom (11) into the recess of the drawer sides and back (8), (9) & (10).

Attach the drawer handle (13) using screw (G) from the rear of the drawer front (12)

Attach the front of the drawer (12) to the sides of the drawer (8) & (9) using screws (F) Repeat this process for all four drawers.

When inserting the drawers please ensure the runner clip is facing forwards as seen in the image below.

Congratulations stage three is now complete. Your bench is now ready to use.

Certificate of Registration

This is to certify that HATYSRL “the certified site” has been certified in accordance with the requirements of the Forest Stewardship Council® A.C. using the FSC® Chain of Custody standards* and that HATY SRL of Calea lui Traian, Nr. 201, Babeni, Valcea, 24S100, ROMANIA
is hereby licensed to use the FSC Logo on and sell as FSC certified all products listed on the attached FSC product schedule as FSC 100%

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LUMBERJACK User Manuals

Related Manuals