PixLinkCam WI-FI Smart Camera App Installation Guide
- August 30, 2024
- PixLinkCam
Table of Contents
PixLinkCam WI-FI Smart Camera App
Download and install
Scan the QR code below to download and install the “PixLinkCam” APP. IOS is available on the Apple Store and Android is available on GooglePlay.
Note:
It is recommended to use the browser or a third-party scanning software to
scan and download the APP. The scanning function of wechat does not support
downloading apps directly.
Add a device
Click “+” to add the activated camera, or click the “+” button in the upper right corner of the App. The connection modes include direct connection to the Device AP, network distribution for the device AP, and Online Device Addition. Add 4G Device Select a connection mode.
Tap Device AP Direct Connection to connect the device. Go to WIFI configuration and select the appropriate hotspotConnect (for example, “DGOF” format). If the connection is successful, return to APP and the device is addedSuccess. (If the APP does not automatically add devices, click search to add devices)
Once the camera is online, click on the camera you just added to watch the live video. You can control the device in the video interface and click the page icon to set it as required.
Click You can connect to WIFI. The network configuration is successful. Procedure (Note: Connection required 2.4G WIFI network)
Click on the top right corner “ ” Icon to view multiple video screens at the same time.
Product setting interface functions:
Motion detection function:
When the motion detection function is enabled, the device will be
automatically displayed in front of the camera Take pictures when the dynamic
picture is abnormal.
Note:
If the application always fails, try checking the following:
- A. The mobile phone is not connected to the AP of the camera, The configuration is to connect the mobile phone to the AP hotspot to the camera.
- B. Common routers are supported. Public routes that require login page authentication are not supported for the time being.
- C. Pay attention to the network name, network password, and UID when configuring.
- D. Currently, Chinese Wifi name passwords and special symbols are not supported.
- E. The Wi-Fi signal of 5G is not supported.
Common Problem
-
Why can’t the APP search detect the camera/can’t configure the network?
A: Please confirm that the device is connected normally, and check whether the APP usage permission is restricted. -
Why does the camera always ask for a username and password, or rather, the incorrect user?
A: The default password of the camera is admin. If you forget the username or password, you can restore the camera to the factory settings to obtain the default username and password. -
How can I restore the camera to factory settings?
A: Please press the reset button of the camera for about 5 seconds until the camera restarts.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for
uncontrolled enviroment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>