Kavomati KM-6T Solar Tire Pressure Monitoring User Manual

Kavomati KM-6T Solar Tire Pressure Monitoring

Product Specifications

• Product Size: W21 x H17 x D21 mm
• Product Weight: 10g
• Sensor Battery Life: Around 1 year (Depending on the use environment)

Product Usage Instructions

Before Using the Product
Please check the following before using the product:

• This product is designed for use on public roads, avoid harsh conditions like track driving.
• Check the receiver screen only when the vehicle is stopped.
• The sensor battery enters power-saving mode after 10 minutes of vehicle stoppage. Data transmission resumes when the speed exceeds 20 km/h
• Tire pressure and temperature vary with weather, time of day, and road conditions.

Installation Method – Sensor Battery Replacement

1. Rotate sensor counterclockwise to remove the cover.
2. If difficult, use the special wrench provided to turn the cover.
3. Insert CR1632 battery with the + side facing up.
4. Ensure the battery is inserted all the way.
5. Securely close the sensor cover by turning it clockwise.
6. Note: Ensure the cover is tightly closed to prevent water damage.

Receiver Installation
Use 3M tape to fix the receiver on the instrument panel in a suitable position in the car. Avoid metal and other electronic devices within 50 cm to prevent interference.

QR Code Installation Video
You can scan the QR code with your mobile phone to watch the installation video.

Frequently Asked Questions (FAQ)

• Q: How do I know when to replace the sensor battery?
  A: The receiver will display a battery replacement icon when the sensor battery needs to be replaced. Follow the provided instructions to replace it.

• Q: Where should I install the receiver in my car?
  A: Use the provided 3M tape to fix the receiver in a suitable position on the instrument panel, ensuring it is within easy view of the driver and away from metal or other electronic devices.

User Manual
ITEM LIST

Solar tire pressure monitoring
After unpacking, please check whether all items are included and the product is not damaged. If there is a shortage or defect, please contact the store where you purchased it.

• Receiver introduction

• Tire sensor (6 pcs)
  CR1632 battery is installed in the sensor

• Special wrench

• Anti-theft nut (6 pcs)
  Nut prevents falling off

• Pieces of 3M glue
  (2 pcs)

Safety instructions

Please check the following items before using this product

• This product is designed for use on public roads, so do not use it in harsh conditions such as track driving.
• If you want to check the receiver screen while driving, be sure to do so while the vehicle is stopped.
• In order to extend the life of the sensor battery , the device will enter power saving mode if the vehicle is stopped for a period of time (approximately 10 minutes). In power saving mode, the sensors will automatically transmits data if the vehicle speed more than 20 km/h.
• Tire pressure and temperature change according to the weather, time of day and road conditions. Especially when driving, And it is normal that the pressure value fluctuate suddenly after receiving the signal when car started.
• Tire pressure will naturally drop over time and this drop has nothing to do with this unit.
• Please make sure the sensors were installed correctly to prevent it from falling off due to vibration or other reasons.
• When installing sensors, tight the sensors correctly. If too tight, it may damage the rubber gasket of the valve and sensor. So be careful when installing..
• After installing the sensor, use soapy water to check if there is air escaping from the sensor.
• This product can monitor, warn and remind abnormal tire pressure, but it cannot prevent the occurrence of tire blowout accidents.

About pressure and temperature

Parts Name/Product Specifications

Display interface description

• Pressure unit: You can choose Bar or Psi as unit, default is Bar. You can switch it in setting mode.
• Tire pressure: If the tire pressure more than the High pressure alarm or less than the low pressure alarm you set, there will be sound alarm meanwhile the alarm icon will flash.
• Air leakage display: Displayed when air leakage occurs.
• Temperature warning display: Displayed If the tire temperature more than the high temperature value you set
• Temperature unit: You can choose in °C or °F, default unit is °F, can switch in setting mode
• Low battery display: Displayed when the sensor battery is low.

Receiver Specifications

• Input power： USB DC5V / 0.5A
• Lithium battery capacity: 500mAh
• Operating temperature： -22°F ~ 176°F
• Operating pressure： 0 ~ 8.0Bar (±0.1Bar)
• Product size： W89 x H29 x D65 mm
• Product weight： 68g

Sensor specifications

• Operating frequency：433.92 MHz ±30KHz
• Power and capacity：CR1632 (140mAh)
• Operating temperature： -22°F ~ 176°F
• International protection code：IP67
• Product size： W21 x H17 x D21 mm
• Product weight： 10g
• Sensor battery life around: 1year Depending on the use environment

Installation method

• Replace sensor battery
• When purchased, sensors already include batteries, You can use directly.
• If the battery used up, battery replacement icon appears on the receiver, we recommend to replace the sensor battery.

1. Rotate sensor counterclockwise cover and remove it
2. Insert the CR1632 battery(with the +  side faced up)
3.  Turn the sensor cover clockwise to close it  securely.

• You can scan it with your mobile phone QR code to watch the installation video
• We are unable to respond by phone\ or email Inquiries about installation work

Receiver installation

• Use 3M tape to fix it at a suitable position on the instrument panel in the car. The recommended location area is as shown below. 

• ( Note: Install the receiver in the driver’ s direct view area or in a position where it is easy to see. You should try to stay away from metal and other electronic products, such as driving recorders, DVDs and other equipment on the car, try to stay away from more than 50 cm.)

• Sensor place
  The position of each sensor on the screen.

• Side view of the car.

Sensor installation
If the sensor is installed when the value is wet, or it may malfunction. Make sure the parts are dry before installation.

1.  Screw the anti-theft nut into the valve
2.  Install the sensor onto the valve and tighten
3. Use the included special wrench to turn the nut counterclockwise to tighten it. If the sensor is not screw tightly, it may drill off during using.
4. After installation is complete, spray soapy water around the valve and gearbox sensor to check for air leaks.

Turn receiver on/off

1. Press and hold the return key    for 3 seconds to turn on the receiver.
2. The display will show the previous value (factory value). When the vehicle speed exceeds 20km/h, the tire pressure and temperature will automatically updated and displayed.

Check transmitter sensor battery voltage

1. Short press the SET button, will show the voltage of the sensor battery.
2. Short press the SET button again, will show the battery level of the sensor battery.
3. If there is no operation for 5 seconds, it will automatically return to the tire pressure interface. In battery level interface, display 30, which means 3.0V.

Function setting method

Set high pressure alarm
If the tire pressure more than the high pressure value you set, it will alarm.

• Initial setting value: 6Bar
• Setting range: 0.3Bar ~ 8.0Bar

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.

2. Press the SET button  several times until it  show P3. Then press OK button.

3. Press the SET button several times until it show H1, then press OK button (different batches the default valves may different)
   Depending on the time of shipment, the initial setting values may differ from the chart (initial setting values).

4. When the pressure value flashes, press the SET button to set the value you want, then press OK button to confirm it

5. Leave it or Press back button to back to main  interface.

Set low pressure alarm
If the tire pressure less than the low pressure value you set, it will alarm.

• Initial setting value: 3Bar
• Setting range: 0.2Bar ~ 7.9Bar

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.
2. Press the SET button several times until it  show P3. Then press OK button.
3. Press the SET button several times until it show LO, then press OK button (different batches the default valves may different) Depending on the time of shipment, the initial setting values may differ from the chart (initial setting values).
4. When the pressure value flashes, press the SET button to set the value you want, then press OK button to confirm it
5. Leave it or Press back button to back to main  interface.

Change display mode
The default setting is to display pressure for all tires, But if you want, you can change it to only display 2, 4, or 6 tires.

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.
2. Press the SET button several times until it  show P5. Then press  OK button.
3. Press the SET button several times go to 4 tires display,  Press SET again go  to 6 tires, then press  OK button to confirm.
4. Leave it or Press back button to back to main  interface.

Display turn off

• You can turn off the display of receiver. At main interface, Press and hold the Back button to turn off the display.

• Even the display is off, the sensor still keep works.

• Set temperature alarm
  If the tire temperature more than the temperature you set, it will alarm.

• Initial setting value : 80°C

• Setting range: 50°C ~ 92°C

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.
2. Press the SET button several times until it  show P3. Then press OK button.
3. Press the SET button several times until it show °C, then press OK button (different batches the default valves may different) Depending on the time of shipment, the initial setting values may differ from the chart (initial setting values).
4. When the temperature value flashes, press the SET button to set the value you want, then press OK button to confirm it
5. Leave it or Press back button to back to main  interface.

Sensor lost

When the sensor is lost or in defective, replace with new sensor, you need do the settings as following.

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.
2. Press the OK button
3. Press the SET button several times until the icon of the tire which you want set is flashing, then press OK button, it will display “-” .
4. Install the sensor into the tire.
5. When you hear a sound of “Du” , means setting new sensor is successfully.
6. Leave it or Press back button to back to main interface.

When you change sensor place
When the sensor is lost or in defective, replace with new sensor, you need do the settings as following.

1. Press and hold the SET button until you hear the sound “Di” , and P1 will be displayed.
2. Press the SET button several times until it show P2, then press OK button.
3. Press the SET button several times to choose the place you want, then press OK button to confirm it.
4. Leave it or Press back button to back to main interface.
   Following picture shows the tire1 and tire 5 sensor did exchange the place.

Air leak alarm

1. According to the measured value of the tire while driving, when the air pressure drops sharply, the alarm icon in the center flashes, the air leakage icon is displayed, and the alarm sounds.

2. Solar charging / USB charging
   When there is enough light for charging, a sun icon is displayed, also the battery icon is scrolling, This meaning the device is on charging. You can judge whether the solar charging function is normal or not by put the device in the sun to see if the sun icon appears or not. If there is no sun, you can use cable to charge the receiver.

About maintenance

When driving in snowy weather, the snow melting agent may stick to the sensor and nut, which will cause the sensor is not installed tightly. Please remove the sensor and nut from the air valve regularly to remove snow melting agent and other dirt.

Troubleshooting

If the problem still cannot be solved after taking the following measures, please stop using the product and contact the store where you purchased it to avoid accidents.

car
Out of battery, and Usb cable is not connected| Connect the receiver with power via usb cable.
Display is turned off| Press back button to turn on the display.
The values on receiver did not update| The car did not move after install sensors| Please drive more than 20 km/h.
The battery icon is displayed on receiver| The sensor battery is used up, please replace with new battery for sensor.
The wires are not tightened| Since the wires are dotted wires, do not bundle the wires when using.
Alarm notice| High pressure alarm| Please check the tire situation, and check with high pressure alarm setting you set.
Low pressure alarm| Please check the tire situation, and check with low pressure alarm setting you set.
Temperature alarm| Please check the tire situation, and check the temperature alarm setting you set.
There is a sound of air leakage from the sensor| The sensor cap is on leaking| Please check the condition of your tires. Retighten the sensor, making sure it is not loose.
After driving for a while, the tire pressure increased| if weather is hot, and temperature is high which caused to drive on a hot road, the tire pressure will also increased| Please check the condition of the tires, this is not a fault.

Kavomati online store will gradually launch 4-wheel tire pressure, 8-wheel or more truck tire pressure, Bluetooth tire pressure, etc. Please continue to pay attention.

• Manufacturer: ShenZhen YiGuo Electronic Technology Co., Ltd
• Address: Zip code 518108, 3F-10 Building, JiaYiDa Industrial Park, LiaoKeng New Village， Langxin community,Shiyan Street,Baoan District,ShenZhen,China
• Website: http://www.kavomati.com
• MADE IN CHINA

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>