SunFounder Structural Plates User Manual
- June 7, 2024
- SunFounder
Table of Contents
Preface
About SunFounder
SunFounder is a technology company focused on Raspberry Pi and Arduino open-
source community development. Committed to the promotion of open-source
culture, we strive to bring the fun of electronics making to people all around
the world and enable everyone to be a maker.
Our products include learning kits, development boards, robots, sensor
modules, and development tools. In addition to high-quality products,
SunFounder also offers video tutorials to help you make your own project. If
you have an interest in open source or making something cool, welcome to join
us!
About This Kit
This cute learning kit utilizes blocks and circuit driving connecting rod
structure to command the pig to run. You can learn the knowledge of bricks,
structure, and circuits by applying this kit.
In this book, we will show you how to build the robot via description,
illustrations of physical components in hardware respects.
You may visit our website www.sunfounder.com to
download the related code and view the user manual on LEARN - > Get
Tutorials and watch related videos under VIDEO.
Free Support
If you have any TECHNICAL questions, add a topic under the FORUM
section on our website and we’ll reply as soon as possible.
For NON-TECH questions like order and shipment issues, please send an email to service@sunfounder.com. You’re also welcomed to share your projects on FORUM.
Components
Structural Plates
Prior to assembling the Pig, you need to remove the residues in the holes of the plates and the stickers on the plates.
Mechanical Fasteners
| Parts | Name | Qty. |
|---|---|---|
| M2*4 Self-tapping Screw | 4 | |
| M3*6 Screw | 6 | |
| M3*8 Screw | 6 | |
| M3*12 Screw | 4 | |
 |
M3*16 | |
| Screw | 4 | |
 |
M3*28 | |
| Screw | 3 | |
| M3 self-locking Nut | 12 | |
| M3*6 Bi-pass plastic Standoff | 4 |
| M3*20 Bi-pass plastic Standoff| 2
Electrical Components
| Parts | Name | Qty. |
|---|---|---|
 |
||
| DC motor | 1 | |
| 4 x 1.5v Battery Holder | 1 | |
| Cross Socket Wrench | 1 |
| Phillips Screw Driver| 1
Introduction
This cute learning kit utilizes a bricks element and some circuits to drive
the connecting rod and command the pig to walk. You can learn the knowledge of
brick, structure, and circuit by applying this kit.
It is a new mobile robot called Pig developed by SunFounder. The structure is
to connect the front and behind the leg with two connecting rods. The electric
motor controls the front leg by connecting the rod and drive the behind leg to
move; besides, the left and right connecting rod is assembling symmetrically,
thus the pig can move forward. The circuit is consisting of a battery holder,
four
the battery and an electric motor.
Assembly
The right leg
1 . Face the 11 the board to the arrow side to insert M3*8 screws from the hole of 17 the board and the leg, then fix M3 self-lock nut and M3 screw by the socket. Note: Do as shown in the picture, or else mistakes may occur.
2. Insert the hole of board 9,7,17 and 11 by M312 screw, then fix M3 nut and
M3 screw with the help of socket.
3. Face board 16 to the arrow direction and fix with board 11 by M3 nut and
M38 screws.
The left leg
1 . Face board 11 to the arrow direction and insert M3*8 screw into the hole
of board 11 and 17, then fix M3 self-lock nut and M3 screw with the help of
socket. Note: not to assemble in the reverse direction.
2. Insert board of 9, 7, 17, and 11 by M312 screw and fix M3 nut and M3
screw by the socket.
3. Face the board of 16 to the arrow direction as shown below and fix with
board 11by M3 nut and M38 screws.
The right side
1. Insert the motor into board 2, then insert two M328 screws into motor and
board 2, then fix M36 screws and M3*20 bi-pass plastic standoff at the other
two holes.
2. Put motor shaft on three board 6 and put the motor shaft on the right leg
of board 9. Rotate 17 the board to let it be in the center of the motor, then
fasten M24 screw into the hole by a screwdriver.
3. Insert M316 screws into16 the board and 11 the board, M3*6 bi-pass
plastic standoff and 2 nd board to fasten by M3 nut on the other side.
4. Keep flat of 2 nd board, then insert 12 the, 13 the, and two 10 the board.
The left side
1 . Insert the M316 screw into 16 then, 11 then board on the left leg, and
also M36 bi-pass plastic standoff and 1 st board to fasten with M3 Nut on the
other side.
2. Overlap the other side of the motor with the left inner board, note to
insert all the boards at the last step to insert into the 1 st board, and
insert the M328 screws into the round hole of 1 st board, then fix two M320
bi-pass plastic standoff by M3*6 screws.
3. Put three 6 th boards into the motor shaft and also for 9 th board on the
left leg, then rotate 17 th board until it is aligning with the center of the
motor, then fasten with M2*4 screws into the center of the motor shaft by a
screwdriver.
Note: The 9 th board on the left should be on the reverse side of the right
one.
Assemble Head and Feet
1 ．Insert the 4 the board into 13 the board.
2. Insert two 3 rd boards into the gap of 13 the board.
3. Insert 5 th board into the gap between 3 rd and 4 th , then insert 14 th board into the gap before 4 th board.
4. Insert 15 th board into the gap of 12 th , then insert four 8 th boards into the gap under 16 th and 17 th
Circuit Connection
1. Insert four 5 th batteries (not included) into the battery holder and put back the cover. Insert the battery holder into the two 10 th boards.
2. Connect the red and black lines of the motor with the battery holder.
.
3. Put the pig in a flat place and slide the power switch, then it can walk.
Notes:
- For a better experience, place it on a frictionless surface to walk.
- Screw and self-lock nut should not be too tight, or else, the pig cannot walk smoothly also, unsteady structure and toe out of the four limbs if too loose. Both of them will increase the motor load and lead to battery power faster.
- The front leg can be rotated to the location as shown below. If the legs are in other places, the pig may not stand still, but wouldn’t interrupt the normal work.
Summary
In this manual, having learned the related components for building the robot
kit, you’ve gone through the assembly of the mechanical parts and electrical
modules.
The SunFounder Bio-Robot Kit is adapt for those who had just learned some
knowledge about circuits and structure. After all the study and hands-on
practice of the kit, you can surely have the creative ideas to design the
other kind of bio-robot. Now, get started to make better work!
Copyright Notices
All contents including but not limited to texts, images, and code in this manual are owned by the SunFounder Company. You should only use it for personal study, investigation, enjoyment, or other non-commercial or nonprofit purposes, under the related regulations and copyrights laws, without infringing the legal rights of the author and relevant right holders. For any individual or organization that uses these for commercial profit without permission, the Company reserves the right to take legal action.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>