MZOOM MLS061 Motorcycle Universal LCD TFT Digital Speedometer 14000RPM 6 Gear Backlight Instructions

1. Operating Voltage
   9～18VDC

2. Speedometer
   1. Calculate the vehicle speed according to the received pulse signal
   2. Metric and British
   3. No pulse signal, displayed as 0
   4. The number of backstage magnets and tire circumference can be set
   5. Display speed increase 5%
   6. When there is a speed, 1, 2, and 3 lights are displayed on the horse (Light 1 is 3 LEDs in parallel)

3. Engine speed signal
   Liquid crystal display, 166Hz to 10 × 1000r / min.
   The number of cylinders can be set in the background
   Set to 2: 166.6Hz for 10 × 1000RPM
   Set to 4: 333.3Hz corresponds to 10 × 1000RPM
   Over-rotation headlights: the speed is 9-10 × 1000RPM, the yellow light is always on
   Over-rotation light: The yellow light turns off when the speed reaches 10 × 1000RPM or more, and the red light blinks at 2Hz.

4. Fuel
   Liquid crystal display, with fuel sensor connected, fuel block display, no connection without display
   1. When judging whether there is a sensor, there is no sensor, and the fuel related is not displayed. If there is a sensor, it is displayed according to the corresponding resistance range.
   Judge the presence or absence of a sensor, a value is being judged, not just power on, it will judge
   3.No driving damping, the entire segment is 10 seconds, driving damping, 7 seconds per division
   4. The fuel level is as low as 1 block and below, the front oiler flashes
   5. Set 2-wire or 3-wire sensors in the background

Piece| 0 block, E, F, tanker
symbol flashes| 1 flash, oil pot
flash| 1Piece| 2Piece| 3Piece| 4Piece| SPiece
---|---|---|---|---|---|---|---
2 lines| 900 above| 89-81| 80-71| 70-53| 52-34| 33-15| 14 0 below
3 lines| 531 0
above| 530-501| 500-401| 400-284| 283-168| 167-57| 50 0 below
5. **Water temperature

** 1. When judging whether there is a sensor, there is no sensor, and the water temperature is not displayed. If there is a sensor, it is displayed according to the corresponding resistance range.
2. Judge the presence or absence of a sensor, a value is being judged, not just power on, it will judge
3. 2 seconds data average
4. The higher the temperature, the smaller the resistance value. When the resistance value is lower than the number set in the background, the LED lights up, and the LED lights up.
5. When the temperature is too high, the water temperature symbol is red and flashes.

6. Key Function
   A. Press the button briefly to switch between total (ODO) and subtotal (TRIP).
   B. On the subtotal TRIP interface, press and hold the button for 3 seconds to clear the subtotal
   

7. Clock adjustment
   In the total state, long press the button for 3 seconds, the clock hour will always be red, and the second will not flash. Short press the button and add 1, long press the button
   (The second switches to the quantile red and is always displayed, the second does not flash, press the button shortly to increase 1, and then press the button for 3 seconds to save and exit, debug If there is no operation for 5 seconds, save and exit

8. LCD screen
   TFT 4.3 inch screen 480 * 272 1000 1000cd / m²

9. Oil lamp
   Press and hold the button for 3 seconds, the light goes off, and enter the next round of counting at the same time
   

10. DJ621-E2.8*05
    DJ7031A-2.8-21
    1. Black: Keylock (12V positive)
    2. Brown: Backlight +
    3. Blue / White: Fuel signal
    4. Light blue: turn right
    5. Red and black: Engine speed signal
    6. Red: battery (normal power, 12V positive)
    7. Blue: High beam
    8. Green: negative
    9. Orange: turn left

11. DJ621-E2.8*05
    DJ7031A-2.8-21
    1. Pink: 1 file
    2. Blue / Red: 2 levels
    3. Green / Black: 3 levels
    4. Yellow / Red: 4 levels
    5. Green / Red: N files
    6. Yellow / White: 5 levels
    7. Gray: 6 levels
    8. Brown/red: Engine failure
    9. Green / White: water temperature

12. 
    Motor oil

13. 
    Background control buttons

14. DJ621-E2.8*05
    DJ7031A-2.8-21
    1. Red / White: Sensor positive
    2. Green / Blue: sensor negative
    3. Black / White: sensor signal

Background parameter setting

Press and hold the button, ACC power on, enter the background password interface, short press plus 1, long press to shift, enter the correct password 6810, the following interface is displayed. Press briefly to cycle through the items, and press and hold to modify the displayed value. ACC power-down restart takes effect.

SteppingS00
Software version| Software version| MCU+ARM|

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>