CARSON 500907125 Rundumlicht Orange Mit Elektronik Instruction Manual
- June 6, 2024
- Carson
Table of Contents
CARSON 500907125 Rundumlicht Orange Mit Elektronik Instruction Manual
Before using your product for the first time or ordering any spare parts, check that your manual is fully up-to-date. This manual contains the technical appendices, important instructions for correct start-up and use and product information, all fully up-todate before going to press. The contents of this manual and the technical data of the product can change without prior notice.
For the latest version of your manual, see: www.carson- modelsport.com
Dear Customer
We congratulate you for buying this CARSON product, which is designed and
manufactured using state of the art technology.
According to our policy of continued development and product improvement we reserve the right to make changes in specifications regarding equipment, material and design at any time without notice.
Specifications or designs of the actual product may vary from those shown in this manual or on the box.
The manual forms part of this product. Should you ignore the operating and safety instructions, the warranty will be void.
Keep this guide for future reference.
Limited Warranty
This product is warranted by CARSON against manufacturing defects in materials and workmanship under normal use for 24 months from the date of purchase from authorised franchisees and dealers. In the event of a product defect during the warranty period, return the product along with your receipt as proof of purchase to any CARSON store.
CARSON will, at its option, unless otherwise provided by law:
- (Correct the defect by repairing the product without charging for parts and labour;
- Replace the product with one of the same or similar design.
All replacement parts and products, and products on which a refund is made, become the property of CARSON. New or reconditioned parts and products may be used in the performance of warranty services.
Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period.
The Warranty does not cover:
- Damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current;
- Damage caused by losing control of your model;
- Any repairs other than those provided by a CARSON authorised service facility;
- Consumables such as fuses or batteries;
- Cosmetic damage;
- Transportation, shipping or insurance costs; or
- Costs of product removal, installation, set-up service adjustment or reinstallation;
- Any changes to plugs and cables, open the housing and damage the sticker.
This warranty gives you specific legal rights, and you may also have other rights which may vary according to the country of purchase.
The explanation of the symbol on the product, packaging or instructions: Electronic devices are valuable products and should not be disposed of with the household waste when they reach the end of their service life! Help us to protect the environment and respect our resources by delivering this appliance to the relevant recycling point.
We wish you a lots of fun using your CARSON product!
Before use, read this manual carefully!
This product is not a toy. Its control must be learned step by step. Children under 14 years of age should operate the product only under adult supervision.
TECHNICAL DATA
- Input voltage: BEC 4.8 – 5 V / external supply 7.2 V
- Output voltage: corresponds to the input voltage
- Current per output: max. 100mA
ASSEMBLING THE ROTATING BEACON
LIGHTING MODULE
The lighting module has 4 outputs (each with a max. 100mA) and there is a choice of 6 different settings. With a 3-way tumbler switch or 2/3-way momentary switch (on-off-on), two settings can be programmed and activated via the remote control.
CONNECTING THE ROTATING BEACON
Connect the module directly to a free channel on the receiver. Pay attention to the polarity.
If the module and outputs are powered by the receiver (BEC), the jumper must be inserted on the left. In this case, do NOT connect the cable for the external power supply. The output voltage for this setup scenario is 5 V (BEC voltage from the receiver). The outputs can also be powered by an external power supply with a maximum voltage of 7.2 V. In this case, the jumper must be inserted in the right-hand position. Ensure that the connections are made with the correct polarity.
WARNING!
Connecting the cable with reverse polarity will result in damage or a defect!
FUNCTIONS OF THE CONTROL BOARD
The board is activated when the power supply to the RC receiver (BEC) is switched on and it re-learns the zero position of the switch at every switch- on. In the course of this, the miniature lamps at the output light up at half brightness. During this time, the button/ switch should be in the “Off” position. Otherwise, malfunctions can occur. Once the miniature lamps have gone off, the module is ready for operation.
The programmes can be activated by pressing the button/switch once and deactivated by pressing the button/switch again.
Upon delivery the module is configured as follows:
Programme1: Rotating beacon function A clockwise 40ms
Programme2: Rotating beacon function B anti-clockwise 40ms
Programme 1: Sets the “clockwise” rotary direction via the switch,
Programme 2, ” anti-clockwise” rotary direction. If the programme is changed
from programme 1 to programme 2, for example, the previously activated
programme is ended automatically. And vice-versa.
PROGRAMMING THE MODULE
The assignment of the settings A … F can be freely chosen for both programmes.
Assignment of the setting (A – F) … for programme 1:
- Step 1: Activate programme 1 by pressing the button/switch upwards
- Step 2: After this, again press the button/switch upwards and hold for at least 7sec. When two miniature lamps flash, the next setting has been selected.
- Step 3: Repeat step 2 until the desired setting is obtained.
- Step 4: Once the desired setting has been selected, press/hold the switch/button downwards for >10sec. to save the Programme- Setting assignment. Successful saving is confirmed by two miniature lamps flashing.
Assignment of the setting (A – F) … for programme 2:
- Step 1: Activate programme 2 by pressing the button/switch downwards
- Step 2: After this, again press the button/switch downwards and hold for at least 7sec. When two miniature lamps flash, the next setting has been selected.
- Step 3: Please repeat step 2 until the desired setting is obtained.
- Step 4: Once the desired setting has been selected, press/hold the switch/button downwards for at least 10sec. to save the Programme-Setting assignment. Successful saving is confirmed by two miniature lamps flashing.
Overview of the possible settings:
A: Anti-clockwise (medium speed)
B: Clockwise (medium speed)
C: Anti-clockwise (high speed)
D: Clockwise (high speed)
E: Anti-clockwise (slow speed)
F: Clockwise (slow speed)
Please refer to the table below for the precise sequence of signals of the separate settings:
TAMIYA-CARSON
Modellbau GmbH & Co. KG
Werkstraße 1 // D-90765 Fürth // www.carson-modelsport.com
+49 3675 7333 343
Service-Hotline for Germany: Mo – Do 8 -12 Uhr & 12.30 -16 Uhr // Fr 8 -12.30
Uhr
CARSON-Model Sport // Abt. Service // Mittlere Motsch 9 // 96515 Sonneberg
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>