Shenzhen Lizi Technology V002 Car Wireless Charger Phone Holder Instructions
- June 6, 2024
- Shenzhen Lizi Technology
Table of Contents
Car Wireless Charger Phone Holder
User Instructions
Notice
- Before using this product, please read the instruction manual first. And the use of this product in accordance with the instructions of this use.
- When the mobile phone is used to charge the mobile phone, the air conditioning of the car can not open the hot air. Must be closed using a single air outlet,
- In the use of the mobile phone wireless charging support mobile phone charging, ln order to ensure the best effect of mobile phone charging must use a lighter head quality brand charger.
- Please use the manufacturer-approved and this type of equipment USB charging cable for charging,
- We do not take any responsibility for failure to use the product instructions in accordance with the requirements of the product instructions.
- Please keep this manual for future use.
Product specification :
Product size : 100x9MM
Input : 12V/L5A;9V/1.67A5V/2A
Output : 15W;10W;7.5W5W
Packing list :
The car air outlet wireless mobile phone holder x1
USB Data charging line xl
Packing box x1
Use instructions x1
Product appearance
Installation instructions
-
Press the adjustment button by button 1 to move left and right 2 cell phone clips are expanded)Suitable for mobile phone size.
-
The outlet clamp button can be adjusted to different automobile
outlets according to rotation different car models rotate 360 ° (4) presses the button open clamp clip clip in and out the otherTuyere. to 360 ° 4presses the button open clamp clip clip in and out the otherTuyere. -
5 Place one end of the USB charging cable on the automobile cigarette lighter and one end on the product jack
-
Mobile phone tilt placement center lock (6 charging center)
Note: the blue light of the charging indicator 7 is in standby mode, and the red light is in charge state.
Support models
Ps: and other wireless charging models; Does not support wireless charging
model can be used with a wireless charging receiver.
Apple: iPhone XS iPhone XR iPhone XS MaxiPhone 8, iPhone 8P, iPhone X Samsung:
S9 NOTE9 GALAXY note8, GALAXY note7, GALAXYnote5, GALAXY s6, GALAXY s6 edge,
GALAXY s6 edge+, GALAXY s7, GALAXY s7 edge, GALAXY s8, GALAXY s8+
Nokia: Lumia 820, Lumia 830, Lumia 920, Lumia 930, Lumia 1020, Lumia 1050,
LUMIA 1520
Google: Nexus 4, Nexus 5, Nexus 6
LG: G2, G3, G10
Xiaomi: Mix 3 Mix 2S
Huawei: Mate 20, Mate 20 Pro, Mate 20 , RS P20
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. NOTE: This equipment
has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
RF warning for WPT device:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. During the operation of the device, a distance of
15cm surrounding the device and 20 cm above the top surface of the device must
be respected.