Shenzhen Junfeng Xinye Electronic JM01 Smart Watch User Guide
- June 6, 2024
- Shenzhen Junfeng Xinye Electronic
Table of Contents
Shenzhen Junfeng Xinye Electronic JM01 Smart Watch
Message push interface
click the screen to view historical information, If there is no history
message, the screen will be blank. 1.69 inch large screen, large font, more
content display, easy to see.
Status interface
Switch to the interface to see the current number of steps, distances and
calories. The distance and calories are calculated and displayed on the basis
of the current walking steps and the height and weight set by the APP
individual.
Heart rate test note:
- During the test, the heart rate LED on the back of the bracelet will light up.
- When testing, the sensor should stick to the skin to avoid the influence of external light on the accuracy of the test.
Sports interface
Switch to the interface, click the screen to enter into the specific sports
interface, including thirteen modes such as rope skipping, swimming, riding,
ping-pong, climbing etc., slide the screen then enter the specific sports
interface.
Heart rate interface
Switch to the heart rate interface, click the screen to enter the heart rate
detection. After the test is completed, press side button to exit the heart
rate detection. You can also connect to the mobile phone App, in the heart
rate interface to test or stop. If the bracelet is not worn correctly or
failed, the final failure interface will be displayed. Under the heart rate
detection mode, the duration of the bracelet will be reduced.
Temperature interface
Switch to the temperature interface, click the screen to enter the temperature
detection. After the test is completed, press side button to exit the
temperature detection. You can also connect to the mobile phone App, in the
temperature menu until test stop. If the bracelet is not worn correctly or
failed, the final failure interface will be displayed.
Blood pressure interface
Switch to the blood pressure interface, click the screen to start testing
blood pressure. Once blood pressure test completed press side button to exit
the blood pressure mode. If test start it will show the results of the last
test or “-/-” when the results are not measured; also you can connect to the
phone App, in the blood pressure interface once the test stop, test result
same as above
Information interface
In the message interface, click the main screen to view the message,slide the
screen to turnover the pages. Press the side button to exit the interface.
Quick instructions for use
Part of introduction
Charging method
For the first time, please take the wristband out and charge the equipment with
the corresponding charger. When charging, the wristband will open
automatically. (charge mode as follows: Joint the USB-charging cable with Band
at match point back side and USB port for charging. Charge voltage 5V.)
To keep the test area clean, sweat or stains will affect the test results.
Wearing method
- Best wear the wristband behind malleolus ulnaris;
- Adjust the size suitable for the size of wrists via Adjustment Hole, fasten wrist strap buttons;
- Sensor shall be close to skin avoiding moving.
Power on/off
- In the state of the wristband shutdown, Charging or long press the side button for about 3 seconds the watch will power on.
- When the wristband is in the boot state, Switch to the shutdown interface, long press the interface or press the side button for about 3 seconds, the wristband vibrates and shuts down.
operation
- When the device starts up, to touch the screen or slide the interface to lighten screen or switch over display;
- The screen shall be screen off without operation for 5 seconds and users can connect the phone to App to modify the screen off time.
- The wristband is default as open status for calling and message reminding,user can connect to App and change the open/off status.
- Press the Return Button at any time to return back to previous menu interface.
Settings interface
You can enter the sub menu by click on the related interface, and then perform and operate more related functions.
Brightness adjustment : Click the main screen to adjust different
brightness, there are the 5 levels that you can click to choose any of them.
Find the phone: In the connection state, click the screen to interfact of
finding the mobile phone, the phone will ring out to remind. Version
information: Under the About interface, you can view the firmware version
number and Bluetooth address of the watch.
Restore settings: Long press on the restore interface, and all the record
data will be erased, and the APP data will be cleared that day (the rest of
the historical data will remain).
Shutdown: The interface can be shut down after you click the interface
menu and the wristband will vibrate.
Return: Press the side button of the breacelet to exit
Install the wristband APP
Scan the following QR codes or enter into various large application markets to download and install “ GloryFit”.
Device requirement: iOS9.0 and above; Android 4.4 and above
Device attachment
When being used for the first time, it is necessary to connect APP for
alignment. After successful connection, wristband will self-synchronize time,
or otherwise, step calculation and sleep data won’t be accurate.
Bluetooth connection: after successfully matching, APP will automatically
save the wristband bluebooth address. When APP is opened or operated in
background, it will automatically search and link with the wristband.
Data Synchronism : manually pull down the synchronization data on the
APP home page; the bracelet can store off-line data for 7 days, the more data,
the longer the synchronization time is, and the longest time is about 2
minutes.
APP functions and setting
Personal information and exercise goals
After entering into APP, please first set up personal information Me → Click
avatar
- Head portrait, gender, age, height and weight can be set up and personal information can enhance accuracy of data.
- Customize personal everyday exercise goals. A reasonable exercise plan is helpful for promoting body quality.
Reminding function
For reminding function, a reminding switch shall be switched on in APP-end
Setting Center, mobile phone and wristband shall be kept to be connected
successfully and there will be vibrating reminders when there are messages.
Call remindin : when the caller calls, the ring will shake and the name
or number of the caller is displayed. (if the caller’s name has been saved in
the phone address book, the name is displayed, otherwise the display number)
Message reminding : when a text message arrives, the wristband will
vibrate and display the SMS icon reminder; the address message of the address
book contact person displays the name, and the short message number of the
stranger.
QQ reminding: when the QQ information arrives, the ring will vibrate and
display the QQ icon.
WeChat reminding : when the WeChat information is received, the hand ring
will shake and the WeChat icon reminds
Alarm clock reminding : it can set up three alarm clocks, and will
synchronize to the bracelet after setting up. The intelligent alarm clock is a
silent alarm clock. When the alar is on, the bracelet will cause moderate
vibration, and support the offline alarm clock reminder.
Other reminding: when receiving email or other information, the wristband
vibrates and displays other reminder icons. Click to see the content.
Charging: When the wristband is connected to the power, the motor
vibrates, and the wristband does not vibrate.
Sleep detection function
When you fall asleep, the wristband will automatically determine the sleep
monitoring mode, automatically detect your deep sleep / shallow sleep /
wakefulness time, calculate your sleep quality, and sleep data temporarily
support APP only.
Note: you can get sleep data when you go to sleep with a hand ring.
Main functional interface
Main interface
The wristband has multiple main interfaces, and the interface can be switched
after click on the main interface. After the first pairing of APP, the
wristband will synchronize the time, date and week of the cell phone.
Matters needing attention
- Please avoid strong impact, extreme heat and exposure to the wristband. Please do not disassemble, repair or transform the device on its own.
- This machine is charged with 5V 500MA, and it is strictly forbidden to use overvoltage load power.
- The use of the environment is 0 degrees ~45 degrees, and it is forbidden to throw it into the fire so as not to cause an explosion.
- Please wipe off the water with a soft cloth and then the wristband can be used for the charging operation , otherwise it will cause corrosion of charging contact point and charging inciddent may occur.
- Do not touch the chemical substances such as gasoline, clean solvent, propanol, alcohol or insect repellent.
- Please do not use this product in high pressure and high magnetic environment.
- If you have sensitive skin or tighten the wristband, you may feel discomfortable
- Please dry the sweat drips on the wrist in time. The strap has long contact with soap, sweat, allergies or pollution ingredients, which may cause skin allergy itching.
- If it is often used, it is recommended to clean the wristband every week. Wipe with wet cloth and remove oil or dust with mild soap.
- It is not appropriate to wear a hot bath with a wristband.
- After swimming, please wipe the wristband in time so as to keep dry.
Common problems
Why is the first test of heart rate too long?
To test your heart rate, you need to take a long time signal to accurately
calculate your heart rate.
What do Bluetooth connections do? (connection / reconnection failure or
connection speed is slow)
Confirm whether your device system is Android 4.4 or its higher versions , and
IOS9.0 or its higher versions, and your device support Bluetooth 4.0.
- Because of the problem of signal interference in Bluetooth wireless connection, there may be no time to connect each other. If the connection is not long enough, please ensure that the operation is carried out without magnetic field or without multi Bluetooth device interference.
- Turn off Bluetooth and open.
- Turn off the mobile phone background application or restart the mobile phone. Mobile phones do not connect to other Bluetooth devices or functions at the
- same time.
- APP is running normally in the background and may not be connected if it is not in the background.
Can’t search the wristband?
Since the wristband is not searched by phone in Bluetooth broadcast, make
sure the wristband is in power and activated and is not connected to anyother
phones. Then, put the wristband close to the phone, if it is still invalid,
turn off the phone, and after about 20 seconds, restart the phone Bluetooth.
Why the wristband should be worn more tightly when measuring heart
rate?
The wristband uses light reflection principle, penetrates the skin through the
light source, and collects the signal reflected to the sensor, to calculate
your heart rate. If you don’t wear it tightly, there will be ambient light
reaching into the sensor, which will affect measurement accuracy.
Why not remind when opening the reminder function?
Android phone: confirm that the phone and the wristband are connected, and open
the corresponding permissions in the phone settings, allowing the ” GloryFit”
APP access calls, messages and address book, and keeping “GloryFit” running in
the background; if the phone is installed with security software, add ”
GloryFit” to “trust”. Iphone: If there is no reminder after the connection, it
is recommended to restart the phone to reconnect, when reconnecting the
wristband again, there will be reminder after popping up “Bluetooth pairing
request” and clicking “Pairing”.
Is the wristband waterproof?
It supports IP68 waterproof and dust-proof level (IP68 standard is 35 degrees
below water, 1 meters below 30 minutes). Usually, wash hands, rain, cold water
shower, wash ca can be worn with heart.
Does the Bluetooth connection need to be open all the time? Is there any
data after disconnection?
Before the data is synchronized, the data is kept on the wristband host (seven
days of data can be retained). When the Bluetooth connection of the wristband
and the wristban is successful, the wristband data will be automatically
uploaded to the mobile terminal. Please synchronize the data to the mobile
terminal in time.
Note: if the caller and SMS alerts are opened, you must keep the
Bluetooth connection, and the alarm is offline.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>