TRUPER 14436 Positioning Cable Polyester Rope Instructions

TRUPER 14436 Positioning Cable Polyester Rope

USE AND SAFETY INSTRUCTIONS

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE USING THE EQUIPMENT AND MAINTAIN A SAFE WORK ENVIRONMENT.

Proper use of fall arrest systems can save lives and reduce the potential of serious injuries from a falling. Please read and follow all instructions. Failure to follow precautions could result in serious injury or death. Pregnant women, children and people with back or neck problems, should NOT perform work at heights.

WARNINGS AND PRECAUTIONS TO PROTECT AGAINST FALLS

• ’s fall and protection systems are designed to work in any working environment where height conditions are of at least six feet (6’) above the ground.
• Maximum working load is 308 lbs. including clothing and tools.
• People involved in this type of work should provide the skills, proper training, and the ability to evaluate risk situations, using the correct equipment in excellent condition and under continuous inspection to be protected against present or potential hazards.

COMPONENTS OF THE PERSONAL FALL PROTECTION SYSTEMS

Fall protection systems are designed to be used by a single person; if the job requires more than one person, each person should count with it’s own fall protection system, independent from the rest of the work team. The Fall protection system is composed of:

• Body Harnesses: Main component of the fall protection system, consisting of a system of straps which may be secured around the worker in such a way that it will distribute the fall arrest forces over thighs, pelvis, waist, chest and shoulders. These straps attach to other components of the personal fall arrest system. Body belts and positioning belts do not stop falls and do not work as body harnesses. They are used to allow an adequate positioning only.
• Connecting Devices: Secondary component in a fall protection system. On one end it attaches to the body harness and at the other end it attaches to an anchor point. Shock-absorbing lanyards and retractable lifelines are the most commonly used, as well as standard lanyards or other deceleration devices. Their function is to significantly reduce fall arresting forces.
• Anchor Points: The final component of a fall protection system is the anchor or tie-off point. Anchor points provide a secure location for the attachment for lifelines, lanyards or deceleration devices. Anchorage connectors may be necessary between the connecting device and the anchor point. The anchor point must be able to support 5 000 lbs. per worker.

FALL PROTECTION FUNCTIONAL CATEGORIES

• Fall Arrest: A fall arrest system is required whenever a working height of six feet (6’) or more is reached. It is a passive means to protect the user in the event a fall should occur.
  Positioning: A personal positioning system is one that enables the user to maintain their position in a hands-free environment, allowing them complete use of their hands while working. This system is used together with a fall arrest system as a backup. Working in places with more than six feet (6´) high.

• Rescue: A rescue system is primarily used in confined places where a worker may be lowered into a space (manhole, etc.) and possibly require a fast retrieval due to an emergency situation.

GENERAL PRECAUTIONS AND INSTRUCTIONS

• Users should read and understand all warnings and instructions before using the equipment, and be aware of the risks involved in working at heights.
• It is the employer’s responsibility to educate and train workers in heights about properly use of fall protection equipment, procedures to reduce work risks and have a rescue plan and the means to implement it in case of accident.
• Only trained personnel using PPE (personal protective equipment) may perform work at heights.
• The fall protection equipment must be used only for the purpose for which it was designed. NOT to be used for towing or lifting.
• NEVER abuse or misuse the fall protection equipment.
• ALWAYS use compatible components. equipment is designed to be compatible. Use of non-approved components or subsystems may alter the correct functioning of the personal fall system and can put the user at serious risk.
• Cotton ropes, natural fiber ropes or ropes of any other material that do not meet the standards should not be used to replace or supplement personal fall arrest systems.
• The equipment must be protected from slag, sparks, flames or other heat sources, as well as chemicals that can damage the material, reducing its effectiveness against falls. Use heat-resistant equipment to perform welding work or where exposed to heat.
• Consider environmental factors to select the suitable fall protection equipment.
• DO NOT perform work at heights near power lines and other sources of energy.
• Use extreme caution when using this equipment around moving machinery, electrical sources, sharp edges or abrasive surfaces.
• NEVER use positioning equipment without the support of fall arrest equipment when justifying the use of the latter (heights of six feet or more).
• Anchor points for personal fall arrest systems must be independent to the anchors used to support platforms, and must be capable of supporting at least 5000 lbs. per worker
• Inspect all fall protection equipment before each use.
• Always make sure all hooks and buckles around the fall protection system are fully closed and secured.
• NEVER use stairs as an anchor point.
• NEVER use multiple pressure hooks to attach the D-rings.
• NEVER use snap hooks that do not have a closing system and that are completely held. Check that entrenched systems ensure the hook perfectly in place before starting the job and that the same entrenched system is not the same as the one that supports and prevents a possible fall.
• NEVER alter, restrict or disable the hook’s mechanism.
• NEVER fix a connection onto itself. NEVER use two or more fixed connections onto each other. Never set more than one connection to a single anchor point.
• Never tie knots to the connections, otherwise they will loose nominal strength.
• Never attach or surround a connection to a sharp beam or structure.
• Always pay attention to the connection cable to prevent entanglement and avoid stepping on it.
• Any equipment that has stopped a freefall, is NOT certified to stop a second fall. Should be discarded immediately and not be used again for work at heights.
• Due to the diverse nature of anchorage connectors, please contact for any specific product information and usage.
• This equipment must be stored in a cool and dry place, free from contact with dust, chemicals, corrosive substances or hazardous gases, as well as staying away from direct contact of sunlight.
• All users of fall protection equipment should be free of a medical history with conditions that can aggravate with a fall, they should be mentally healthy and not be under the influence of alcohol or drugs. Not paying attention to these factors can result in serious injury or even death.
• The free fall distance should never exceed six feet (6’). (A).
• Make sure there are no obstructions below the work area in order that the worker is not beaten by any obstacle in case of a fall (B).
• ALWAYS keep the connected anchor point above the back D-ring.
• ALWAYS keep the work area just below the anchor point to prevent a pendulum effect in case of a fall (C).

ALWAYS CALCULATE THE SAFE FALL DISTANCE

Please consider the total length on cable to be used (shock absorbing lanyard or positioning rope) at the height to work.

PLACEMENT OF CONNECTIONS

• One of the ends of the connection should be attached to the back D-ring of the harness located on the back of the harness; the other end should be attached to an anchor point (D). The side, front and chest D-rings are for positioning only (Model ARN-5436 y ARN-5438). Shoulder D-rings are for rescue only (Model ARN-5437 y ARN-5438) (E).
• The two-line connections are used to be connected at all times to the lifeline during position changes or changes of anchor points while working at heights. Use the free line connection when changing position or changing to another anchor point, while always maintaining the other line fixed in an anchor point. The free line can be fixed to a positioning or rescue D-ring only during the change of position.
• Inspect all fasteners to ensure they are properly closed and secured before each use.
• We recommend the use of latches either spring or brooch. NEVER use snap hooks to connect a D-ring.
• All shock absorbing or retractable lifelines must be connected to the anchor point using a snap hook closure. This hook is usually fixed to the rotating component via a hole in the top of the retractable roof.

PLACEMENT AND LOCATION OF ANCHOR POINTS

• Prior to installing all fall protection system anchorage, carefully inspect the location in which the device will be secured.
• The site must be stable and not cause damage to the equipment due to sharp or jagged edges. ALWAYS make sure that any snap hooks or carabiners within the entire fall protection system are completely closed and locked.
• An anchor point must be kept above and to the rear of the D-ring to avoid swing-fall injuries (pendulum effect).
• Always use an anchor point, which is compatible with the snap hook or carabiner.
• Never use an anchor point which will not allow the snap hook keeper to close.
• Make sure the anchorage point is strong enough to withstand the forces generated by a fall. For it, to be legal, it must support 5,000 lbs per worker.
• Never attach multiple connecting devices to a single anchor point.

INSPECTION OF FALL PROTECTION EQUIPMENT

• All fall protection equipment must be regularly inspected by a person responsible for their safety, as well as by the respective user before each use to ensure they are in perfect condition and meet safety standards. Should be inspected carefully:
  Webbing Straps: After grasping the webbing with your hands about 6-8 inches apart, bend the strap in an inverted “U” shape. This enables damages to be more visible. Continue this procedure until all the webbing has been inspected. Make sure that there is no evidence of frayed edges, broken fibers, pulled stitches, cuts, burns or chemical damage.
  D-Rings: All D-rings should be checked for distortion, cracks, breaks and rough or sharp edges.
  Snap Hooks & Carabiners: Snap hooks should not be cracked or distorted. Snap hook keepers must be free of burrs, clean and not bent. Visually check all snap hook and carabiner connections. Make sure that all snap hooks and/or carabiners are able to close and lock properly.
  Buckles: Make sure that all buckles are free of any distortion. The outer and center bars must be straight. Corners and attachment points should be given additional attention. Note any unusual wear, as well as any frayed or cut materials.

• The entire unit is to be free from burns, cuts, cracks, sharp edges, chemical deformation, corrosion, heat damage, abrasions, kinks, knots, broken strands, fraying, broken or pulled stitching, alteration and excessive wear or aging. Any equipment exhibiting deformities, unusual wear or deterioration must be immediately discarded.

• If the equipment does not pass inspection, it should be marked unusable and destroyed and must be immediately substituted with other equipment.

MAINTENANCE

• fall protection equipment is made with strong and durable materials and designed to function well in a variety of applications.
• In order that your equipment has a longer service life and continued high performance, it is necessary to maintain and inspect your equipment before each use.
• Equipment which is in need of or scheduled for maintenance shall be tagged as “unusable” and removed from service until proper maintenance has been concluded.
• Equipment must be destroyed if subjected to an impact.
• Never alter or attempt to repair this equipment. Repairs must be performed only by the equipment manufacturer or persons/companies authorized in writing by the manufacturer.
• Wash polyester webbing with warm water and a mild detergent. Avoid harsh chemicals.
• Lubricate the snap hooks with light lubricating oil.
• Store away from direct sunlight in a dry, cool area free from oil, degrading elements, chemicals and their fumes.

Do not remove the label .

CUSTOMER SUPPORT

Importado por: Truper, S.A. de C.V. Parque Industrial #1, Jilotepec, Estado de México, Méx.,
C.P. 54240,
Hecho en China / Made in China, Tel.: 76 1 782 9100 03-2020.
www.truper.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>