Jimi loT JM-VL04 LTE Gnss Tracker User Manual
- June 6, 2024
- Jimi loT
Table of Contents
Jimi loT JM-VL04 LTE Gnss Tracker
Introduction
Features
- Inertial navigation
- Audio broadcast of alerts
- Remote Listen-in
- Location data re-upload
- Anomaly alerts (speeding, fatigue driving, geofence, plug-in and -out, collision, etc.)
- Driving behavior analysis
- Multi-GNSS
- ACC detection
- Smart power saving
Operating Environment
- Operating voltage: 9‒36VDC
- Internal backup battery: 3.7V/50mAH LiCoO2 battery
- Operating current: <300mA @12V
- Standby current: <10mA @12V
- Operating temperature: ‒20℃ to 70℃
- Bluetooth 4.0: 2402-2480 (-11±2 dBm)
- Storage temperature: ‒40℃ to 85℃
- Positioning accuracy: <10m
- Location modes: GPS, GLONASS, BDS, Galileo, AGPS, and LBS
Frequency Bands
Overview
Appearance
Connotations of Indicators
Power Indicators (Red)
Network Indicators (Green)
Installation
Inserting the SIM Card
-
Step 1 Prepare a proper SIM card;
-
Step 2 Insert the SIM.
Flip the slot cover open and insert the SIM in correctly
NOTE
- After the SIM card is inserted, the device powers on using the backup battery. If the device fails to power on due to low battery, you can connect the device to the OBD port of the vehicle to obtain power.
- Note: The SIM card must be inserted correctly, has GPRS services activated, and is not in arrears. If the SIM is identified and requires a PIN, please disable the PIN request.
Installing the Device
Connect the device to the OBD port when the vehicle is ignition off.
Observe the indicators against 2.2 to ensure that the device enters work mode
correctly.
- A: Most car models of General Motors, Volkswagen, Ford, Toyota, Hyundai, Citroën, BMW, etc.
- B. Honda, Volkswagen Touran, Lexus, etc.
- C. Dongfeng Citroën, Dongfeng Peugeot, etc.
- D. Dongfeng Citroën, etc.
- E. Others
Description
The following functions can be configured via the platform or app provided by your dealer. If the configuration via the platform or app fails, you can configure via SMS. You will receive reply messages indicating whether a function is configured successfully.
Plug-out Alert
If the device is unplugged from the vehicle, it will send an alert
notification to the platform or app, or send an SMS carrying the alert reason
and location to the SOS number.
Power Cut Alert
If the power to the device is cut, the device will send an alert notification
to the platform or app, or send an SMS carrying the alert reason and location
to the SOS number.
Installation Alert
If the device detects the charger is connected or powers on using an external
power source, it will determine that it has been connected with the OBD port
of the vehicle and send an installation alert notification if no plug-out
action is detected for 10s.
Low External Power Alert
If the voltage of the external power is under the preset threshold, the device
will send a low external power alert notification to the platform or app.
Low Backup Battery Alert
If the state of charge (SoC) of the backup battery of the device is lower than
10%, the device will send a low battery alert notification to the platform or
app.
Geofence Alert
You can draw a circular or rectangular area via the platform or app and set it
as a geofence. If your vehicle is detected to enter or leave a preset
geofence, the device with the related alert feature enabled will send an alert
notification to the platform or app. The device will also give out an audio
reminder indicating that your vehicle has entered or left the monitored range.
Speed Alert
After a speed threshold is set, the device will send an alert notification to
the platform or app and give out an audio reminder of slowing down if it
detects that your vehicle keeps moving at speeds above the threshold for a
preset duration.
Fatigue Driving Alert
If the device detects the vehicle has been moving for more than the preset
duration (4 hours by default) continually with rest intervals less than the
minimum rest time required (20 minutes by default), it will send a fatigue
driving alert notification to the platform or app and give out an audio
reminder of taking a proper rest 30 minutes before the fatigue driving alert
is generated.
UBI-related Event Alert
If the device detects that the driver has stepped on the brake or gas pedal
hard, cornered rapidly, or changed lanes suddenly or that the vehicle has
collided, rolled over, become unstable, or has an abnormal Euler angle, it
will send an alert notification to the platform or app and give out an audio
reminder as well.
Vibrating alert
When the device in manual defense mode has its defense on and has enabled with
the vibrating alert feature, if the device detects the vehicle vibrates for 5
times in 10s (the trigger condition is configurable), it will send an alert
notification to the platform or app.
When the device in auto defense mode has its defense on and has enabled with
the vibrating alert feature, if the device detects the vehicle vibrates for 5
times in 10s (the trigger condition is configurable) and the vehicle is not
ACC on in 30s, it will send an alert notification to the platform or app . If
the vehicle has its ACC on in 30s, no vibrating alert will be triggered.
Defense On and Off Alerts
If the device is in manual defense mode, you can enable or disable the defense
with the following methods:
Enable and disable defense via SMS
Send the SMS “111” via an SOS number to the device, the device will enable
defense after receiving the command and reply with a message indicating the
execution result.
To disable the defense, send the SMS “000” via any preset SOS number to the
device, the device will disable the defense after receiving the command and
reply with a message indicating the execution result.
Enable and disable defense via the platform or app. Whether the command is
executed successfully or not, the device will reply with a message indicating
the result.
Note: This feature is disabled by default. You can enable it via the
platform or app.
Platform Operations
By logging in to the mobile app or location services platform designated by your dealer and correctly binding your device, you can query and set related parameters.
Logging In to Service Platform
Log in to the location services platform designated by your dealer and
configure accordingly.
Downloading Mobile App
Log in to the URL designated by your dealer to download the mobile app.
Troubleshooting
When any of the following faults occurs, please troubleshoot it by the solution. If the fault persists, please contact your dealer or service provider.
Warranty Instructions and Service
Disclaimer
- No prior notice will be given if the product is upgraded due to technological reasons.
- The appearance or color of the product is subject to the actual.
- The warranty card applies to the services of repair, replacement, and refund of the product with the following IMEI.
- Please keep this warranty card and the original purchase receipt
- together in a safe place, as these will be needed at time of services.
Warranty Terms
- For damages not caused by human factors, this warranty lasts for 2 (two) years (including one year replacement service) from the date of purchase.
- You can choose to pay for the repair services in any of the following cases:
Warranty Instructions and Service
The warranty card expires;
- No warranty card or valid proof of purchase;
- The product, including its accessories, is not in the warranty period;
- Damage caused by unauthorized repairs, crash, liquid spillage, accident, modifications, or incorrect voltage input; or the label, IMEI, or counterfeit mark of the device is broken or scribbled;
- Damages caused by installation or use not in accordance with the user manual;
- Damage caused by force majeure such as fire, flood, or lightening;
- The product model is inconsistent with the warranty card or the warranty card is altered;
- Other damages caused by force majeure.
Reminder
As of January 1, 2016, the warranty lasts for 2 (two) years for repair from
the date of purchase, including one year for replacement.
The specific terms are:
- A full replacement, including accessories, if the product is found defective during unpacking check;
- If a defect occurs within one year after installation, then:
- Replace only the mainboard if the housing is intact and doesn’t affect normal use;
- Replace the housing and the mainboard if the housing is defective and affects normal use. Please be noted that man-made damages will void the replacement service for the housing.
- Free repair services will be given to the device if a defect is found during the second year under proper use.
RF Exposure Information and Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE: Unauthorized modifications could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:(1) this device may not cause harmful
interference,and (2) this device must accept any interference received,
including interference that may cause undesired operation.
EU regulatory conformance：
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of 20cm between the device and the human body.
To maintain compliance with RF exposure requirement, use product that maintain
a 20cm distance between the device and human body.
CE DOC
Hereby, [Shenzhen Jimi IoT Co., Ltd.] declares that the radio equipment type
[JM-VL04] is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
www.jimiiot.com
Manufacturer information:
Company name: Shenzhen Jimi IOT Co.,Ltd
Address：3-4/F, Block A, Building #7, Shenzhen International Innovation
Valley, Dashi 1st Road, Nanshan District, Shenzhen, Guangdong, China