Huizhou Hezhongxiang Keji Youxian Gongsi KD-2008LB Turntable Record Player Instruction Manual

Huizhou Hezhongxiang Keji Youxian Gongsi KD-2008LB Turntable Record Player

Made In China
www.codi-tech.net

Thanks for purchasing this player

Feel free to enjoy our Turntable Player

Known our player highlight function

• LP music:3 speed LP with 7’’ ,10’’,12’’ size record
• Bluetooth: Freely listening our player music from external Bluetooth speaker by our Bluetoothreceiving device Out function or RCA function
• LP&BLUETOOTH MODE SWITCHED AUTOMATICALLY
• Voice prompts for Bluetooth status:The Bluetooth device is ready to pair.
• Voice prompts for LP:Di dong
• Voice prompts for AUX in: Aux in put mode

Let us start to enjoy now

General of Instruction

Please read this manual carefully before using the product to ensure proper use.Keep thismanualin a safe place for future reference.

• What is included in the package
• Know our product structure and component
• Know our playing function
• How to play LP，Bluetooth ,Aux in and RCA out
• Turntable specification
• Know replacing the turntable stylus
• Warranty Card

Safety Instruction

This product has been well-tested and adjusted，and strict examination of its qualitybeforeallowed to leave the factory.Please check and follow the manual instructions carefully.Anyneglect,misuse,abuse,accident,failures caused by software problem,modify without WOCKODERauthorized,power surges,and any loss or damage arising out of circumstances beyond WOCKODER’ Scontrol,we will not be responsible for the result.

What is included in the package

After you open the package,Please check the items as below carefully before being used.

1. Turntable player KD-2008LB: 1pcs
2. Operation Manual: 1pcs
3. DC adaptor 5V 1.5A: 1pcs

Know our product structure and component

1. Dust cover
2. Turntable player
3. 45RPM fixator
4. Tone Arm
5. Tone Arm Raise Lever
6. Tone Arm Clip
7. Stylus
8. Auto Stop Switch
9. LP Speed Switch
10. Power on/off and volume control
    -Short time knob press to power on
    -Long time knob press to power off
    -Rotate L/R to turn up/down the volume
11. Headphone jack
12. Light indicator
13. Power adaptor jack
14. .RCA output jack(for active speaker)RCA
15. Aux in jack Aux in

Know our playing function

After connect the power adaptor,press the Power button（）,the player starts to workwhilevoice reminding and LED blue light. Please refer to below description to better operate

How to play Bluetooth:

Bluetooth play mode: Bluetooth mode as default .Press the Power button(),the playerstarts to work while voice reminding and LED blue light flash() quickly. You can hearthevoice:”The Bluetooth device is ready to pair.’’Once paired,the Blue light flash slowly.Thelovely songs on your Bluetooth device will be transferred to turntable to sound and control.

How to play LP:

LP disk play mode: It shows enter to LP mode successfully once you can hear the voice”Didong”.Then place a LP disk on the turntable platter and select the desired speed(33/45/78)bysliding the speed selection switch() according to the LP disk specification.Open the tonearm clip() to release the arm upon the LP disk, and push the Arm Raise Lever() backwardsto raise the arm.Gently move the tone arm() to the desired slowly,then close the arm clip().

Note: When the auto stop switch is turned on,the turntable will continue to spin no matterLP playing or not.

Warning: Do not manual lower the tone arm onto the LP disk,to avoid LP disk and stylus() damage!

How to use Aux in:

Audio JACK /Aux in play mode: Using a right Aux in line to connect between your playingdevice without Bluetooth and our player Aux in jack() on the back panel.Then the soundwill be transferred from another playing device to our player.

How to use RCA out:

RCA output Jack/Connect to speaker: Using a right audio date line to connect betweenyour external speakers(active speakers only)and our player RCA out jack on the backpanel.Then the sound will be transferred from turntable to your lovely external activespeakers.Warmly note,our player sound still be spoke out.

Turntable specification

How to replace the turntable stylus()

Removing the stylus from the Tone Arm Clip()
Place a screwdriver at the tip of the stylus and push downward as shown in direction”A”

1. WARNING: When applying force to stylus too much may damage or break the stylus.
2. Remove the stylus by pulling the stylus forward and pushing downward.

Installing the stylus

1. Hold the tip of the stylus and insert the stylus by pressing as shown in direction“B”
2. Push the stylus upwards as in direction “C”until the stylus locks into

WOCKODER

Light indicator instruction

Operation Details & Quick instruction

When there is no play from Bluetooth or Aux in,the player will automatically shut down after 10 mins.Pleasekindly rotate the Power Button(12)back to the initial position,and restart the player after 5 sec.

While the turntable player has no work in Bluetooth mode or Aux in mode for ten minutes,it will beenteredinto Automatic shutdown state.
If you want to enjoy your music again,You should Restart the turntable after 5 seconds.

1. LP disk play mode: The player will automatically switch to LP disk play mode once rise the Tone Arm(5), andvoice prompts as “Di Dong” to indicate that it entered into LP play mode successfully. Please kindly follow below instruction to play /stop to play the LP disk:
2. Place a LP on the turntable platter and select the desired speed (33 1/3 /45/78) by sliding the speed selection switch according to the LP disk spec.
3. Play the LP disk: Open the tone arm clip to release the tone arm. Push the lift lever backwards to raise the arm. Gently move the tone arm to the desired slowly onto the desired poiton on the LP disk to begin playing.
4. Stop the LP disk: Push the lift lever backwards toi raise the arm, gently move the tone arm to the tone arm clip. Push the lift lever forward and lover the arm slowly, then close the tone arm clip.
   Note: When the auto stop switcj is tuned on, the turntable will continue to spin no matter LP palying or not.

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>